Towards a novel holistic design of organic Rankine cycle (ORC) systems operating under heat source fluctuations and intermittency

2021 ◽  
Vol 147 ◽  
pp. 111207
Author(s):  
Xiaoya Li ◽  
Bin Xu ◽  
Hua Tian ◽  
Gequn Shu
Keyword(s):  
Heat Source ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Holistic Design

Theoretical and experimental investigation of an organic Rankine cycle for a waste heat recovery system

2009 ◽  
Vol 223 (5) ◽  
pp. 523-533 ◽  
Author(s):  
W Gu ◽  
Y Weng ◽  
Y Wang ◽  
B Zheng
Keyword(s):  
Heat Source ◽  
Entropy Generation ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Entropy Generation Rate ◽  
Working Fluid ◽  
Total Entropy ◽  
Waste Heat Recovery System ◽  
Cycle Efficiency

This article describes and evaluates an organic Rankine cycle (ORC) for a waste heat recovery system by both theoretical and experimental studies. Theoretical analysis of several working fluids shows that cycle efficiency is very sensitive to evaporating pressure, but insensitive to expander inlet temperature. Second law analysis was carried out using R600a as a working fluid and a flow of hot air as a heat source, which is not isothermal, along the evaporator. The result discloses that the evaporator's internal and external entropy generation is the main source of total entropy generation. The effect of the heat source temperature, evaporating pressure, and evaporator size on the entropy generation rate is also presented. The obtained useful power is directly linked to the total entropy generation rate according to the Gouy—Stodola theorem. The ORC testing system was established and operated using R600a as a working fluid and hot water as a heat source. The maximum cycle efficiency of the testing system is 5.2 per cent, and the testing result also proves that cycle efficiency is insensitive to heat source temperature, but sensitive to evaporating pressure. The entropy result also shows that internal and external entropy of the evaporator is the main source of total entropy generation.

Calculation and Optimization of Heat Transfer between the Low Exergy Heat Source and Organic Rankine Cycle Applied to Heat Recovery Systems

2013 ◽  
Vol 597 ◽  
pp. 45-50
Author(s):  
Sławomir Smoleń ◽  
Hendrik Boertz
Keyword(s):  
Heat Transfer ◽  
Heat Source ◽  
Heat Recovery ◽  
Power Plants ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Optimization Procedure ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Total System

One of the key challenges on the area of energy engineering is the system development for increasing the efficiency of primary energy conversion and use. An effective and important measure suitable for improving efficiencies of existing applications and allowing the extraction of energy from previously unsuitable sources is the Organic Rankine Cycle. Applications based on this cycle allow the use of low temperature energy sources such as waste heat from industrial applications, geothermal sources, biomass, fired power plants and micro combined heat and power systems.Working fluid selection is a major step in designing heat recovery systems based on the Organic Rankine Cycle. Within the framework of the previous original study a special tool has been elaborated in order to compare the influence of different working fluids on performance of an ORC heat recovery power plant installation. A database of a number of organic fluids has been developed. The elaborated tool should create a support by choosing an optimal working fluid for special applications and become a part of a bigger optimization procedure by different frame conditions. The main sorting criterion for the fluids is the system efficiency (resulting from the thermo-physical characteristics) and beyond that the date base contains additional information and criteria, which have to be taken into account, like environmental characteristics for safety and practical considerations.The presented work focuses on the calculation and optimization procedure related to the coupling heat source – ORC cycle. This interface is (or can be) a big source of energy but especially exergy losses. That is why the optimization of the heat transfer between the heat source and the process is (besides the ORC efficiency) of essential importance for the total system efficiency.Within the presented work the general calculation approach and some representative calculation results have been given. This procedure is a part of a complex procedure and program for Working Fluid Selection for Organic Rankine Cycle Applied to Heat Recovery Systems.

scholarly journals Performance Investigation of Solar ORC Using Different Nanofluids

2019 ◽  
Vol 9 (15) ◽  
pp. 3048
Author(s):  
Reyhaneh Loni ◽  
Gholamhassan Najafi ◽  
Ezzatollah Askari Asli-Ardeh ◽  
Barat Ghobadian ◽  
Willem G. Le Roux ◽  
...  
Keyword(s):  
Heat Source ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Heat Transfer Fluid ◽  
Working Fluid ◽  
Fluid Flow Rate ◽  
Different Types ◽  
Condenser Temperature ◽  
Cubical Cavity ◽  
Al2o3 Nanofluid

A parabolic solar dish concentrator, as the heat source of an organic Rankine cycle (ORC), can be used for power generation. Different types of tubular cavity receivers with different nanofluids can be considered for use in the solar dish collector to improve its efficiency. In the current research, an ORC with three different cavity receivers including hemispherical, cubical, and cylindrical are investigated using three nanofluids: Al2O3/oil, CuO/oil, and SiO2/oil. A numerical model is validated using experimental data. The ORC analysis is done for a constant evaporator pressure of 2.5 MPa, and condenser temperature of 38 °C. Methanol is employed as the ORC’s working fluid and a non-regenerative, ideal ORC system with different turbine inlet temperatures is considered. Furthermore, a fixed solar heat transfer fluid flow rate of 60 mL/s and dish diameter of 1.9 m is investigated. Results show that, compared to pure oil, the thermal efficiency of the cavity receivers increases slightly, and the pressure drop increases with the application of nanofluids. Furthermore, results show that the cubical cavity receiver, using oil/Al2O3 nanofluid, is the most efficient choice for application as the investigated solar ORC’s heat source.

Investigations on experimental performance and system behavior of 10 kW organic Rankine cycle using scroll-type expander for low-grade heat source

Energy ◽  
2019 ◽  
Vol 177 ◽  
pp. 94-105 ◽  
Author(s):  
Chih-Hung Lin ◽  
Pei-Pei Hsu ◽  
Ya-Ling He ◽  
Yong Shuai ◽  
Tzu-Chen Hung ◽  
...  
Keyword(s):  
Heat Source ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Low Grade ◽  
System Behavior ◽  
Experimental Performance ◽  
Low Grade Heat

Exergoeconomic comparison and optimization of organic Rankine cycle, trilateral Rankine cycle and transcritical carbon dioxide cycle for heat recovery of low-temperature geothermal water

2019 ◽  
Vol 233 (8) ◽  
pp. 1068-1084 ◽  
Author(s):  
Afsaneh Noroozian ◽  
Abbas Naeimi ◽  
Mokhtar Bidi ◽  
Mohammad Hossein Ahmadi
Keyword(s):  
Sensitivity Analysis ◽  
Low Temperature ◽  
Heat Source ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Cost Ratio ◽  
Exergetic Efficiency ◽  
Geothermal Heat ◽  
Product Cost

Depleting fossil fuel resources and the horrible environmental impacts due to burning fossil fuels emphasize the importance of using renewable energy resources such as geothermal and solar energies. This paper compares performance of CO2 transcritical cycle, organic Rankine cycle, and trilateral Rankine cycle using a low-temperature geothermal heat source. Thermodynamic analysis, exergetic analysis, economic analysis, and exergoeconomic analysis are applied for each of the aforementioned cycles. In addition, a sensitivity analysis is performed on the system, and the effects of geothermal heat source temperature, evaporator pinch point temperature, and turbine inlet pressure on the cycle's performance are evaluated. Finally, the systems are optimized in order to minimize product cost ratio and maximize exergetic efficiency by using the genetic algorithm. Results indicate that the maximum thermal efficiency is approximately 13.03% which belongs to organic Rankine cycle with R123 as working fluid. CO2 cycle has the maximum exergetic efficiency, equals to 46.13%. The minimum product cost ratio refers to the organic Rankine cycle with R245fa as working fluid. Moreover, sensitivity analysis shows that increasing geothermal heat source temperature results in higher output power, product cost ratio, and exergy destruction ratio in all cycles.

Performance Investigation of Solar Organic Rankine Cycle Systems With and Without Regeneration and With Zeotropic Working Fluid Mixtures for Use in Micro-Cogeneration

2020 ◽  
Author(s):  
Wahiba Yaïci ◽  
Evgueniy Entchev ◽  
Pouyan Talebizadeh Sardari
Keyword(s):  
Low Temperature ◽  
Heat Source ◽  
High Efficiency ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Industrial Wastes ◽  
Working Fluid ◽  
Condensation Temperature ◽  
Thermodynamic Performance ◽  
Cycle Efficiency

Abstract Globally there are several viable sources of renewable, low-temperature heat (below 130°C) particularly solar energy, geothermal energy, and energy generated from industrial wastes. Increased exploitation of these low-temperature options has the definite potential of reducing fossil fuel consumption with its attendant very harmful greenhouse gas emissions. Researchers have universally identified the organic Rankine cycle (ORC) as a practicable and promising system to generate electrical power from renewable sources based on its beneficial use of volatile organic fluids as working fluids (WFs). In recent times, researchers have also shown a preference for/an inclination towards deployment of zeotropic mixtures as ORC WFs because of their capacity to improve thermodynamic performance of ORC systems, a feat enabled by better matches of the temperature profiles of the WF and the heat source/sink. This paper demonstrates both the technical feasibility and the notable advantages of using zeotropic mixtures as WFs through a simulation study of an ORC system. The study examines the thermodynamic performance of ORC systems using zeotropic WF mixtures to generate electricity driven by low-temperature solar heat source for building applications. A thermodynamic model is developed with an ORC system both with and excluding a regenerator. Five zeotropic mixtures with varying compositions of R245fa/propane, R245fa/hexane, R245fa/heptane, pentane/hexane and isopentane/hexane are evaluated and compared to identify the best combinations of WF mixtures that can yield high efficiency in their system cycles. The study also investigates the effects of the volumetric flow ratio, and evaporation and condensation temperature glides on the ORC’s thermodynamic performance. Following a detailed analysis of each mixture, R245fa/propane is selected for parametric study to examine the effects of operating parameters on the system’s efficiency and sustainability index. For zeotropic mixtures, results showed that there is an optimal composition range within which binary mixtures are inclined to perform more efficiently than the component pure fluids. In addition, a significant increase in cycle efficiency can be achieved with a regenerative ORC, with cycle efficiency ranging between 3.1–9.8% and 8.6–17.4% for ORC both without and with regeneration, respectively. Results also showed that exploiting zeotropic mixtures could enlarge the limitation experienced in selecting WFs for low-temperature solar organic Rankine cycles.

Sign in / Sign up

Export Citation Format

Share Document