On the Control of the Secondary Cooling in the Continuous Casting Process

1987 ◽  
pp. 161-177 ◽  
Author(s):  
Pekka Neittaanmäki
Keyword(s):  
Continuous Casting ◽  
Casting Process ◽  
Secondary Cooling ◽  
Continuous Casting Process

Numerical Simulation on Optimization of Center Segregation for 50CrMo Structural Alloy Steel

2016 ◽  
Vol 35 (6) ◽  
pp. 583-589 ◽  
Author(s):  
Xiangzhou Gao ◽  
Shufeng Yang ◽  
Jingshe Li ◽  
Hang Liao
Keyword(s):  
Continuous Casting ◽  
Alloy Steel ◽  
Process Parameters ◽  
Casting Process ◽  
Heat Transfer Process ◽  
Equiaxed Crystal ◽  
Secondary Cooling ◽  
Structural Alloy ◽  
Continuous Casting Process ◽  
Cooling Intensity

AbstractTo improve the center segregation of billet for 50CrMo structural alloy steel, a 3D numerical model of solidification and heat transfer process for continuous casting had been established. The influence law of continuous casting process parameters on the secondary dendrite arm spacing (SDAS) and equiaxed crystal ratio had been obtained. It was shown that reducing superheat and casting speed and increasing the secondary cooling intensity could decrease SDAS. Reducing any one of the three parameters could increase the equiaxed crystal ratio. Adjusting only secondary cooling intensity could not make the SDAS and equiaxed crystal ratio change in the desired direction, but regulating the other two parameters could supply this gap. After optimizing the continuous casting process parameters of 50CrMo billet, the defect of center segregation was solved basically.

Secondary Cooling Control of Continuous Casting Process with Model Strategy

2014 ◽  
Vol 998-999 ◽  
pp. 650-653
Author(s):  
Jin Hong Zhang ◽  
Jun Li Jia ◽  
Guo Zhen Wang
Keyword(s):  
Continuous Casting ◽  
Water Distribution ◽  
Control Method ◽  
Casting Process ◽  
Slab Surface ◽  
Secondary Cooling ◽  
Continuous Casting Process ◽  
Slab Continuous Casting ◽  
Cooling Control ◽  
Casting Production

In the continuous casting production casting speed and casting temperature fluctuates frequently, the secondary cooling control of slab surface temperature fluctuation is too big problem, proposes a radical.The utility of the pulling speed cascade water distribution control method, a kind of development.secondary cooling control model for slab continuous casting.

Secondary Cooling Water Distribution Strategy for Beam Blank Continuous Casting

2013 ◽  
Vol 706-708 ◽  
pp. 1553-1557
Author(s):  
Qiang Liu ◽  
Wei Feng Xue ◽  
Bing Mei Zou ◽  
Jian Wu Yan ◽  
Xiao Hua Peng ◽  
...  
Keyword(s):  
Continuous Casting ◽  
Water Distribution ◽  
Cooling System ◽  
Process Analysis ◽  
Cooling Water ◽  
Casting Process ◽  
Heat Transfer Process ◽  
Secondary Cooling ◽  
Continuous Casting Process ◽  
Distribution Strategy

This paper focus on the water distribution of secondary cooling for beam blank continuous casting process. Analysis of the influencing factors and initial determination method for important parameters of secondary cooling water, including specific water, water ratio in each secondary cooling zoon and the amount of water in outer arc, inner arc and sider at one secondary cooling zoon. After that, according to the simulation heat transfer process of the secondary cooling, to improve the secondary cooling system is given. This work provides a reference to the development of secondary cooling system.

Sign in / Sign up

Export Citation Format

Share Document