Flexural Performance of Strengthened Glued Laminated (GLULAM) Timber Beam Using Glass Fibre-Reinforced Polymer (GFRP)

2021 ◽  
pp. 75-92
Author(s):  
A. O. A. Zamli ◽  
R. Hassan ◽  
M. N. M. Sidek ◽  
A. Awaludin ◽  
B. Anshari ◽  
...  
Keyword(s):  
Glass Fibre ◽  
Timber Beam ◽  
Flexural Performance ◽  
Reinforced Polymer ◽  
Glass Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Glass Fibre Reinforced

scholarly journals The Effect of Layers and Bullet Type on Impact Properties of Glass Fibre Reinforced Polymer (GFRP) Using a Single Stage Gas Gun (SSGG)

2014 ◽  
Vol 564 ◽  
pp. 428-433 ◽  
Author(s):  
S.N.A. Safri ◽  
Mohamed Thariq Hameed Sultan ◽  
N. Razali ◽  
Shahnor Basri ◽  
Noorfaizal Yidris ◽  
...  
Keyword(s):  
Impact Energy ◽  
Glass Fibre ◽  
Impact Test ◽  
Single Stage ◽  
Gas Gun ◽  
Reinforced Polymer ◽  
Glass Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Glass Fibre Reinforced ◽  
The Impact

The purpose of this work is to study the best number of layer with the higher impact energy using Glass Fibre Reinforced Polymer (GFRP). The number of layers used in this study was 25, 33, 41, and 49. The impact test was performed using Single Stage Gas Gun (SSGG) for each layers given above with different bullets such as blunt, hemispherical and conical bullets. The gas gun pressure was set to 5, 10, 15 and 20 bar. All of the signals captured from the impact test were recorded using a ballistic data acquisition system. The correlation between the impact energy in terms of number of layer and type of bullet from this test are presented and discussed. It can be summarise that as the number of layer increases, impact energy also increases. In addition, from the results, it was observed that by using different types of bullets (blunt, hemispherical, conical), there is only a slight difference in values of energy absorbed by the specimen.

Quasi-Static Indentation Behaviour of Glass Fibre Reinforced Polymer

2014 ◽  
Vol 970 ◽  
pp. 317-319 ◽  
Author(s):  
Syed Mohd Saiful Azwan ◽  
Yahya Mohd Yazid ◽  
Ayob Amran ◽  
Behzad Abdi
Keyword(s):  
Glass Fibre ◽  
Polyester Resin ◽  
Loading Rates ◽  
Reinforced Polymer ◽  
Glass Fibre Reinforced Polymer ◽  
Static Indentation ◽  
Indentation Tests ◽  
Fibre Reinforced Polymer ◽  
Glass Fibre Reinforced ◽  
Chopped Strand Mat

Fibre reinforced polymer (FRP) plates subject to quasi-static indentation loading were studied. The plates were fabricated from three layers of chopped strand mat glass fibre and polyester resin using vacuum infusion process. Indentation tests were conducted on the plates with loading rates of 1 mm/min, 10 mm/min, 100 mm/min and 500 mm/min using a hemispherical tip indenter with diameter 12.5 mm. The plates were clamped in a square fixture with an unsupported space of 100 mm × 100 mm. The loads and deflections at the indented location were measured to give energy absorption-deflection curves. The results showed that the loading rate has a large effect on the indentation behaviour and energy absorbed.

Bond Properties of Glass Fibre-Reinforced Polymer Dowel Bars in Jointed Concrete

2008 ◽  
Vol 16 (3) ◽  
pp. 187-192 ◽  
Author(s):  
Chan-Gi Park ◽  
Chang-Il Jang ◽  
Sang-Woo Lee ◽  
Jong-Pil Won
Keyword(s):  
Glass Fibre ◽  
Bond Properties ◽  
Reinforced Polymer ◽  
Glass Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Glass Fibre Reinforced

Optimization of microwire/glass-fibre reinforced polymer composites for wind turbine application

2013 ◽  
Vol 113 (3) ◽  
pp. 537-542 ◽  
Author(s):  
F. X. Qin ◽  
H. X. Peng ◽  
Z. Chen ◽  
H. Wang ◽  
J. W. Zhang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Polymer Composites ◽  
Glass Fibre ◽  
Reinforced Polymer ◽  
Glass Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Glass Fibre Reinforced
Sign in / Sign up

Export Citation Format

Share Document