Evaluation of residual stresses in thin tool coatings

N. V. Novikov; M. A. Voronkin; A. B. Bessonov; F. P. Smaglenko

doi:10.1007/bf01524359

Influence of residual stresses in hard tool coatings on the cutting performance

Journal of Manufacturing Processes ◽

10.1016/j.jmapro.2021.08.011 ◽

2021 ◽

Vol 69 ◽

pp. 340-350

Author(s):

K. Bobzin ◽

T. Brögelmann ◽

H.J. Maier ◽

T. Heidenblut ◽

C. Kahra ◽

...

Keyword(s):

Residual Stresses ◽

Cutting Performance ◽

Tool Coatings

Download Full-text

Method to evaluate residual stresses in the laser cutting process

Lasers in Engineering ◽

10.1080/08981500290022752 ◽

2002 ◽

Vol 12 (1) ◽

pp. 27-41 ◽

Cited By ~ 7

Author(s):

Y. Zamachtchikov ◽

F. Breaban ◽

P. Vantomme ◽

A. Deffontaine

Keyword(s):

Residual Stresses ◽

Laser Cutting ◽

Cutting Process

Download Full-text

Prediction of residual stresses and springback after bending of a textured aluminium plate

Journal de Physique IV (Proceedings) ◽

10.1051/jp4:20030185 ◽

2003 ◽

Vol 105 ◽

pp. 175-182 ◽

Cited By ~ 2

Author(s):

L. Delannay ◽

R. E. Logé ◽

Y. Chastel ◽

P. Van Houtte

Keyword(s):

Residual Stresses

Download Full-text

Theoretical study of the prestressing strand's stress by computer modeling methods

Ferrous Metallurgy Bulletin of Scientific Technical and Economic Information ◽

10.32339/0135-5910-2020-111-1139-1148 ◽

2020 ◽

Vol 76 (11) ◽

pp. 1139-1148

Author(s):

A. G. Korchunov ◽

E. M. Medvedeva ◽

E. M. Golubchik

Keyword(s):

Residual Stresses ◽

High Strength ◽

Pearlitic Steel ◽

Internal Stresses ◽

Steel Microstructure ◽

Compressive Stresses ◽

Wide Range ◽

Prestressing Strands ◽

Increasing Temperature ◽

Wire Strand

The modern construction industry widely uses reinforced concrete structures, where high-strength prestressing strands are used. Key parameters determining strength and relaxation resistance are a steel microstructure and internal stresses. The aim of the work was a computer research of a stage-by-stage formation of internal stresses during production of prestressing strands of structure 1х7(1+6), 12.5 mm diameter, 1770 MPa strength grade, made of pearlitic steel, as well as study of various modes of mechanical and thermal treatment (MTT) influence on their distribution. To study the effect of every strand manufacturing operation on internal stresses of its wires, the authors developed three models: stranding and reducing a 7-wire strand; straightening of a laid strand, stranding and MTT of a 7-wire strand. It was shown that absolute values of residual stresses and their distribution in a wire used for strands of a specified structure significantly influence performance properties of strands. The use of MTT makes it possible to control in a wide range a redistribution of residual stresses in steel resulting from drawing and strand laying processes. It was established that during drawing of up to 80% degree, compressive stresses of 1100-1200 MPa degree are generated in the central layers of wire. The residual stresses on the wire surface accounted for 450-500 MPa and were tension in nature. The tension within a range of 70 kN to 82 kN combined with a temperature range of 360-380°С contributes to a two-fold decrease in residual stresses both in the central and surface layers of wire. When increasing temperature up to 400°С and maintaining the tension, it is possible to achieve maximum balance of residual stresses. Stranding stresses, whose high values entail failure of lay length and geometry of the studied strand may be fully eliminated only at tension of 82 kN and temperature of 400°С. Otherwise, stranding stresses result in opening of strands.

Download Full-text