Dependence of Dynamic Tensile Strength of Longyou Sandstone on Heat-Treatment Temperature and Loading Rate

2015 ◽  
Vol 49 (10) ◽  
pp. 3899-3915 ◽  
Author(s):  
Wei Yao ◽  
Ying Xu ◽  
Wei Wang ◽  
Patrick Kanopolous
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Heat Treatment Temperature ◽  
Loading Rate ◽  
Treatment Temperature ◽  
Dynamic Tensile Strength ◽  
Longyou Sandstone

The effect of heat treatment temperature on the mechanical properties of copper M1.

2015 ◽  
Vol 2015 (3) ◽  
pp. 94-97
Author(s):  
Юлия Гусева ◽  
Yuliya Guseva ◽  
Владимир Сакало ◽  
Vladimir Sakalo ◽  
Татьяна Иншакова ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Heat Treatment Temperature ◽  
Tensile Tests ◽  
Treatment Temperature ◽  
Condi Tions ◽  
Solid Copper

Tensile tests of specimens made from solid copper M1 had been conducted. Samples were subjected to heat treatment by heating to temperatures of 200 to 900°C and were cooled in water or air. Values of tensile strength and relative residual elongation were defined. The condi-tions under which solid copper acquires the properties of soft copper installed.

scholarly journals Research on the influence of heat treatment temperature on bearing capacity of high steel grade pipeline during in-service welding

2021 ◽  
Vol 353 ◽  
pp. 01020
Author(s):  
Yan Xu ◽  
Yinglai Liu ◽  
Xianghui Nie ◽  
Zhenjun Feng ◽  
Liang Li ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
High Temperature ◽  
Yield Strength ◽  
Bearing Capacity ◽  
Tensile Properties ◽  
Heat Treatment Temperature ◽  
Heating Temperature ◽  
Treatment Temperature ◽  
Steel Grade

During the welding of in-service pipeline, natural gas is continuously transported in the pipeline, which maintains a high gas pressure. Therefore, the welding process is completed under strong cooling conditions, and welding delay crack is easy to occur. Preheating before welding and heat treatment after welding can effectively control the hardened microstructure, reduce the residual stress and ensure the welding quality. In this study, the influence of heating temperature on the bearing capacity of high steel grade pipe during in-service welding repair was studied. The high temperature tensile test was used to simulate the bearing capacity of the pipe under heating and high temperature environment. It is found that when the heating temperature is below 400°C, the pipe strength remains at the original level. With the increase of heating temperature, when the test temperature is higher than 400°C, the yield strength and tensile strength of the pipe decrease significantly. When the test temperature is 450°C, the yield strength and tensile strength of the material decrease by 15.8% and 11.1%, respectively, compared with the normal temperature, which are lower than the pipe standard requirements. Therefore, it is suggested that when the heat treatment temperature is higher than 400°C during in-service welding repair, it is necessary to consider reducing the pipeline pressure. At the same time, the box furnace heat treatment method was adopted to heat treat the pipe, and the tensile properties of the pipe after heat treatment were tested to analyze the bearing capacity of the pipe after heat treatment. It is found that when the heating temperature is higher than 700°C, the tensile properties of high grade pipeline steel pipe decrease sharply. It is suggested that when the heat treatment temperature is higher than 700°C, the risk assessment of the service safety of the heat treated pipeline should be carried out.

Tensile Strength of Carbon–Carbon Composites: II – Effect of Heat Treatment Temperature

2004 ◽  
Vol 38 (19) ◽  
pp. 1685-1699 ◽  
Author(s):  
Hiroshi Hatta ◽  
Tatsuji Aoi ◽  
Itaru Kawahara ◽  
Yasuo Kogo
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Carbon Composites

Effects of Heat Treatment Temperature on Photocatalytic Activity of TiO2/SiO2 Composite Aerogels

2013 ◽  
Vol 27 (10) ◽  
pp. 1079-1083
Author(s):  
Zhao-Hui LIU ◽  
Gen-Liang HOU ◽  
Xun-Jia SU ◽  
Feng GUO ◽  
Zhou XIAO ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Photocatalytic Activity ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Composite Aerogels

Spin-dependent-magnetoresistance control by regulation of heat treatment temperature for magnetite nano-particle sinter

2009 ◽  
Vol 18 (12) ◽  
pp. 935-938
Author(s):  
H. Kobori ◽  
T. Asahi ◽  
Y. Yamasaki ◽  
A. Sugimura ◽  
T. Taniguchi ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Nano Particle

scholarly journals Water Resistance and Creep Behavior of Heat-Treated Moso Bamboo Determined by the Stepped Isostress Method

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1264
Author(s):  
Teng-Chun Yang ◽  
Tung-Lin Wu ◽  
Chin-Hao Yeh
Keyword(s):  
Heat Treatment ◽  
Water Absorption ◽  
Creep Behavior ◽  
Heat Treatment Temperature ◽  
Water Resistance ◽  
Absorption Efficiency ◽  
Treatment Temperature ◽  
Moso Bamboo ◽  
Phyllostachys Pubescens ◽  
Heat Treated

The influence of heat treatment on the physico-mechanical properties, water resistance, and creep behavior of moso bamboo (Phyllostachys pubescens) was determined in this study. The results revealed that the density, moisture content, and flexural properties showed negative relationships with the heat treatment temperature, while an improvement in the dimensional stability (anti-swelling efficiency and anti-water absorption efficiency) of heat-treated samples was observed during water absorption tests. Additionally, the creep master curves of the untreated and heat-treated samples were successfully constructed using the stepped isostress method (SSM) at a series of elevated stresses. Furthermore, the SSM-predicted creep compliance curves fit well with the 90-day full-scale experimental data. When the heat treatment temperature increased to 180 °C, the degradation ratio of the creep resistance (rd) significantly increased over all periods. However, the rd of the tested bamboo decreased as the heat treatment temperature increased up to 220 °C.

Accelerating the formation of high-quality optical surface layer in ZnO thin films by the increase of heat-treatment temperature

Optik ◽  
2021 ◽  
Vol 232 ◽  
pp. 166527
Author(s):  
Haisu Qian ◽  
Linhua Xu ◽  
Fenglin Xian ◽  
Jing Su ◽  
Xiaoqiang Luo
Keyword(s):  
Thin Films ◽  
Heat Treatment ◽  
Surface Layer ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Zno Thin Films ◽  
Optical Surface ◽  
High Quality
Sign in / Sign up

Export Citation Format

Share Document