Finite element analysis of prestressed concrete pressure vessel. 12F, 10R

1975 ◽  
Vol 12 (8) ◽  
pp. 120
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Prestressed Concrete ◽  
Pressure Vessel ◽  
Element Analysis

FINITE ELEMENT ANALYSIS OF PRESTRESSED CONCRETE VOIDED BRIDGE DECKS

PCI Journal ◽  
1973 ◽  
Vol 18 (3) ◽  
pp. 51-66 ◽  
Author(s):  
J. C. Jofriet ◽  
G. M. McNeice ◽  
P. Csagoly
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Prestressed Concrete ◽  
Bridge Decks ◽  
Element Analysis

scholarly journals Finite Element Analysis of Skirt to Shell Junction in a Pressure Vessel

2017 ◽  
Vol 10 (25) ◽  
pp. 1-10
Author(s):  
Deepali Mathur ◽  
Mandar Sapre ◽  
Chintan Hingoo ◽  
◽  
◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Pressure Vessel ◽  
Element Analysis

Failure analysis of pressure vessel with sight ports using finite element analysis

2020 ◽  
Vol 117 ◽  
pp. 104791
Author(s):  
Nitikorn Noraphaiphipaksa ◽  
Piyamon Poapongsakorn ◽  
Anat Hasap ◽  
Chaosuan Kanchanomai
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Failure Analysis ◽  
Pressure Vessel ◽  
Element Analysis

Establishing Recommended Guidance for Local Post Weld Heat Treatment Configurations Based on Thermal-Mechanical Finite Element Analysis

2016 ◽  
Author(s):  
Phillip E. Prueter ◽  
Brian Macejko
Keyword(s):  
Heat Treatment ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Crack Initiation ◽  
Residual Stresses ◽  
Pressure Vessel ◽  
Post Weld Heat Treatment ◽  
Element Analysis ◽  
Non Linear ◽  
Weld Heat

Post weld heat treatment (PWHT) is an effective way to minimize weld residual stresses in pressure vessels and piping equipment. PWHT is required for carbon steels above a Code-defined thickness threshold and other low-alloy steels to mitigate the propensity for crack initiation and ultimately, brittle fracture. Additionally, PWHT is often employed to mitigate stress corrosion cracking due to environmental conditions. Performing local PWHT following component repairs or alterations is often more practical and cost effective than heat treating an entire vessel or a large portion of the pressure boundary. In particular, spot or bulls eye configurations are often employed in industry to perform PWHT following local weld repairs to regions of the pressure boundary. Both the ASME Boiler and Pressure Vessel (B&PV) Code and the National Board Inspection Code (NBIC) permit the use of local PWHT around nozzles or other pressure boundary repairs or alterations. Additionally, Welding Research Council (WRC) Bulletin 452 [1] offers detailed guidance relating to local PWHT and compares some of the Code-based methodologies for implementing local PWHT on pressure retaining equipment. Specifically, local PWHT methodologies provided in design Codes: ASME Section VIII Division 1 [2] and Division 2 [3], ASME Section III Subsection NB [4], British Standard 5500 [5], Australian Standard 1210 [6], and repair Codes: American Petroleum Institute (API) 510 [7] and NBIC [8] are discussed and compared in this study. While spot PWHT may be appropriate in certain cases, if the soak, heating, and gradient control bands are not properly sized and positioned, it can lead to permanent vessel distortion or detrimental residual stresses that can increase the likelihood of in-service crack initiation and possible catastrophic failure due to unstable flaw propagation. It is essential to properly engineer local or spot PWHT configurations to ensure that distortion, cracking of adjacent welds, and severe residual stresses are avoided. In some cases, this may require advanced thermal-mechanical finite element analysis (FEA) to simulate the local PWHT process and to predict the ensuing residual stress state of the repaired area. This paper investigates several case studies of local PWHT configurations where advanced, three-dimensional FEA is used to simulate the thermal-mechanical response of the repaired region on a pressure vessel and to optimize the most ideal PWHT arrangement. Local plasticity and distortion are quantified using advanced non-linear elastic-plastic analysis. Commentary on the ASME and NBIC Code-specified local PWHT requirements is rendered based on the detailed non-linear FEA results, and recommended good practice for typical local PWHT configurations is provided. Advanced computational simulation techniques such as the ones employed in this investigation offer a means for analysts to ensure that local PWHT configurations implemented following equipment repairs will not lead to costly additional damage, such as distortion or cracking that can ultimately prolong equipment downtime.

Study on the Stress Concentration at the Round Corners of Flat Heads in Pressure Vessels Subjected to Internal Pressure

1996 ◽  
Vol 118 (4) ◽  
pp. 429-433
Author(s):  
H. Chen ◽  
J. Jin ◽  
J. Yu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Intensity ◽  
Stress Concentration ◽  
Internal Pressure ◽  
Pressure Vessel ◽  
Pressure Vessels ◽  
Stress Index ◽  
Element Analysis ◽  
Approximate Formulas

Results from finite element analysis were used to show that the stress index kσ and the nondimensionalized highly stressed hub length kh of a flat head with a round corner in a pressure vessel subjected to internal pressure are functions of three dimensionless parameters: λ ≡ h/dt, η ≡ t/d, and ρ ≡ r/t. Approximate formulas for estimating kσ and kh from λ, η, and ρ p are given. The formulas can be used for determining a suitable fillet radius for a flat head in order to reduce the fabricating cost and to keep the stress intensity at the fillet under an acceptable limit.

Sign in / Sign up

Export Citation Format

Share Document