Phase field modelling of microstructural evolution during the quenching and partitioning treatment in low-alloy steels

2016 ◽  
Vol 112 ◽  
pp. 245-256 ◽  
Author(s):  
M.G. Mecozzi ◽  
J. Eiken ◽  
M.J. Santofimia ◽  
J. Sietsma
Keyword(s):  
Microstructural Evolution ◽  
Phase Field ◽  
Low Alloy Steels ◽  
Quenching And Partitioning ◽  
Field Modelling ◽  
Alloy Steels

scholarly journals Phase-field modelling of transformation pathways and microstructural evolution in multi-principal element alloys

2021 ◽  
Vol 119 (17) ◽  
pp. 171905
Author(s):  
Kamalnath Kadirvel ◽  
Zachary Kloenne ◽  
Jacob K. Jensen ◽  
Hamish Fraser ◽  
Yunzhi Wang
Keyword(s):  
Microstructural Evolution ◽  
Phase Field ◽  
Principal Element ◽  
Field Modelling ◽  
Transformation Pathways

scholarly journals Phase-field modelling of microstructural evolution in primary crystallization

2009 ◽  
Vol 483 (1-2) ◽  
pp. 645-649 ◽  
Author(s):  
Pere Bruna ◽  
Eloi Pineda ◽  
Jose I. Rojas ◽  
Daniel Crespo
Keyword(s):  
Microstructural Evolution ◽  
Phase Field ◽  
Primary Crystallization ◽  
Field Modelling

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Materials for bullet core

2020 ◽  
Vol 2020 (10) ◽  
pp. 8-21
Author(s):  
A. G. Kolmakov ◽  
◽  
I. O. Bannykh ◽  
V. I. Antipov ◽  
L. V. Vinogradov ◽  
...  
Keyword(s):  
High Speed ◽  
Bending Strength ◽  
Low Alloy Steels ◽  
Hard Alloys ◽  
Small Arms ◽  
Alloy Steels ◽  
Materials Used ◽  
Basic Ideas ◽  
New Generation ◽  
Natural Composite

he basic ideas about the process of introducing cores into protective barriers and the most common core patterns and their location in conventional and sub-caliber small arms bullets are discussed. The materials used for manufacture of cores are analyzed. It is concluded that for mass bullets of increased armor penetration the most rational choice can be considered the use of high-carbon low-alloy steels of a new generation with a natural composite structure and hardness of up to 70 HRC. For specialized armor-piercing bullets, cores made from promising economically-alloyed high-speed steels characterized by a high complex of «hardness—bending strength» are better alternative than ones made of hard alloys or tungsten alloys.

UNIFLUX VCM 125

Alloy Digest ◽  
1978 ◽  
Vol 27 (1) ◽  
Keyword(s):  
Carbon Dioxide ◽  
Fracture Toughness ◽  
Weld Metal ◽  
Heat Treating ◽  
Carbon Steels ◽  
Low Alloy Steels ◽  
Electrode Wire ◽  
Molybdenum Steel ◽  
Alloy Steels ◽  
Welding Electrode

Abstract UNIFLUX VCM 125 is a continuous flux-cored welding electrode (wire) that is used to deposit 1 1/4% chromium-1/2% molybdenum steel for which it was developed. Welding is protected by a shielding atmosphere of 100% carbon dioxide. This electrode also may be used to weld other low-alloy steels and carbon steels; however, the weld metal may differ somewhat from 1 1/4% chromium-1/2% molybdenum because of weld-metal dilution. When Uniflux VCM 125 is used to weld 1 1/4% chromium-1/2% molybdenum steel, it provides 95,000 psi tensile strength at 70 F and 24 foot-pounds Charpy V-notch impact at 40 F. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SA-340. Producer or source: Unicore Inc., United Nuclear Corporation.

Sign in / Sign up

Export Citation Format

Share Document