Axial stress-strain behavior of high-strength concrete confined by circular thin-walled steel tubes

2018 ◽  
Vol 177 ◽  
pp. 366-377 ◽  
Author(s):  
Jiepeng Liu ◽  
Yue Teng ◽  
Yusong Zhang ◽  
Xuanding Wang ◽  
Y. Frank Chen
Keyword(s):  
High Strength Concrete ◽  
Axial Stress ◽  
High Strength ◽  
Stress Strain ◽  
Steel Tubes ◽  
Strength Concrete ◽  
Strain Behavior ◽  
Thin Walled

Comparison of Stress-Strain Relationships of FRP and Actively Confined High-Strength Concrete: Experimental Observations

2014 ◽  
Vol 919-921 ◽  
pp. 29-34 ◽  
Author(s):  
Jian Chin Lim ◽  
Togay Ozbakkloglu
Keyword(s):  
High Strength Concrete ◽  
Axial Stress ◽  
Axial Strain ◽  
High Strength ◽  
Confining Pressure ◽  
Confined Concrete ◽  
Lateral Strain ◽  
Stress Strain ◽  
Strength Concrete ◽  
Actively Confined Concrete

It is well established that lateral confinement of concrete enhances its axial strength and deformability. It is often assumed that, at a same level of confining pressure, the axial compressive stress and strain of fiber reinforced polymer (FRP)-confined concrete at a given lateral strain are the same as those in concrete actively confined concrete. To assess the validity of this assumption, an experimental program relating both types of confinement systems was conducted. 25 FRP-confined and actively confined high-strength concrete (HSC) specimens cast from a same batch of concrete were tested under axial compression. The axial stress-strain and lateral strain-axial strain curves obtained from the two different confinement systems were assessed. The results indicate that, at a given axial strain, lateral strains of actively confined and FRP-confined concretes correspond, when they are subjected to the same lateral confining pressure. However, it is observed that, at these points of intersections on axial strain-lateral strain curves, FRP-confined concrete exhibits a lower axial stress than the actively confined concrete, indicating that the aforementioned assumption is not accurate. The test results indicate that the difference in the axial stresses of FRP-confined and actively confined HSC becomes more significant with an increase in the level of confining pressure.

An Experimental Study on the Compressive Behavior of CFRP-Confined High- and Ultra High-Strength Concrete

2013 ◽  
Vol 671-674 ◽  
pp. 1860-1864 ◽  
Author(s):  
Thomas Vincent ◽  
Togay Ozbakkloglu
Keyword(s):  
Experimental Study ◽  
High Strength Concrete ◽  
Axial Stress ◽  
Concrete Strength ◽  
Experimental Studies ◽  
High Strength ◽  
Compressive Behavior ◽  
Stress Strain ◽  
Strength Concrete ◽  
Ductile Behavior

It is well established that external confinement of concrete with fiber reinforced polymer (FRP) sheets results in significant improvements on the axial compressive behavior of concrete. This understanding has led to a large number of experimental studies being conducted over the last two decades. However, the majority of these studies have focused on normal strength concretes (NSC) with compressive strengths lower than 55 MPa, and studies on higher strength concretes have been very limited. This paper presents the results of an experimental study on the compressive behavior of FRP confined high- and ultra high-strength concrete (HSC and UHSC) with average compressive strengths of 65 and 100 MPa. A total of 29 specimens were tested under axial compression to investigate the influence of key parameters such as concrete strength and method of confinement. All specimens were cylindrical, confined with carbon FRP and were 305 mm in height and 152 mm in diameter. Results obtained from the laboratory testing were graphically presented in the form of axial stress-strain relationships and key experimental outcomes are discussed. The results of this experimental study indicate that above a certain confinement threshold, FRP-confined HSC and UHSC exhibit highly ductile behavior. The results also indicate that FRP-wrapped specimens perform similar to concrete-filled FRP tube (CFFT) specimens at ultimate condition, however notable differences are evident at the transition region when comparing stress-strain curves.

Predictive Stress-Strain Models for High Strength Concrete Subjected to Uniaxial Compression

2014 ◽  
Vol 567 ◽  
pp. 476-481
Author(s):  
Nasir Shafiq ◽  
Tehmina Ayub ◽  
Muhd Fadhil Nuruddin
Keyword(s):  
Predictive Models ◽  
High Strength Concrete ◽  
Cement Content ◽  
Strain Curve ◽  
High Strength ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Strength Concrete ◽  
Strain Behavior ◽  
Four Cylinders

To date, various predictive models for high strength concrete (HSC) have been proposed that are capable of generating complete stress-strain curves. These models were validated for HSC prepared with and without silica fume. In this paper, an investigation on these predictive models has been presented by applying them on two different series of HSC. The first series of HSC was prepared by utilizing 100% cement content, while second series was prepared by utilizing 90% cement and 10% Metakaolin. The compressive strength of the concrete was ranged from 71-87 MPa. For each series of HSC, total four cylinders of the size 100×200mm were cast to obtain the stress-strain curves at 28 days.It has been found that the pattern of the stress-strain curve of each cylinder among four cylinders of each series was different from other, in spite of preparing from the similar batch. When predictive models were applied to these cylinders using their test data then it was found that all models more or less deficient to accurately predict the stress-strain behavior.

Sign in / Sign up

Export Citation Format

Share Document