Cardanol as a dispersant plasticizer for an alumina/toluene tape casting slip

2001 ◽  
Vol 21 (16) ◽  
pp. 2873-2878 ◽  
Author(s):  
K Prabhakaran ◽  
Asha Narayanan ◽  
C Pavithran
Keyword(s):  
Tape Casting ◽  
Casting Slip

scholarly journals Synthesis and Colloidal Processing of Nanocrystalline (Y2O3-Stabilized) ZrO2 Powders by a Surface Free Energy Controlled Process

1996 ◽  
Vol 432 ◽  
Author(s):  
Detlef Burgard ◽  
Rüdiger Nass ◽  
Helmut Schmidt
Keyword(s):  
Free Energy ◽  
Tape Casting ◽  
Slip Casting ◽  
Particle Sizes ◽  
Colloidal Processing ◽  
Average Pore ◽  
Growth Technique ◽  
Casting Slip ◽  
Temperature And Pressure ◽  
Processing Techniques

AbstractUsing the controlled growth technique, nanocrystalline ZrO2 powders have een prepared from solution. By variation of the Y-content (0-8 mol %), redispersable monoclinic, tetragonal or cubic ZrO2 powders with particle sizes between 5 and 10 mn were obtained after crystallization at elevated temperature and pressure. Nanodisperse suspensions of the powders have been used for colloidal processing techniques such as tape casting, slip casting or extrusion. The resulting green bodies with densities of 55 % and average pore sizes of 5 nm could be sintered at temperatures below 1100 °C leading to monoclinic, tetragonal or cubic ZrO2 ceramics.

Phase Inversion Tape Casting and Electrochemical Performance of Solid Oxide Fuel Cell Anode

2015 ◽  
Vol 30 (12) ◽  
pp. 1291
Author(s):  
ZHANG Yu-Yue ◽  
LIN Jie ◽  
MIAO Guo-Shuan ◽  
GAO Jian-Feng ◽  
CHEN Chu-Sheng ◽  
...  
Keyword(s):  
Fuel Cell ◽  
Electrochemical Performance ◽  
Solid Oxide Fuel Cell ◽  
Phase Inversion ◽  
Tape Casting ◽  
Solid Oxide ◽  
Oxide Fuel ◽  
Cell Anode ◽  
Fuel Cell Anode

scholarly journals Microstructure and Thermoelectric Properties of (Bi0.48Sb1.52)Te3 Thick Films Prepared with Tape Casting Method

Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 140
Author(s):  
Lichen Liu ◽  
Ziping Cao ◽  
Min Chen ◽  
Jun Jiang
Keyword(s):  
Thermoelectric Properties ◽  
Low Cost ◽  
Thick Films ◽  
Tape Casting ◽  
Casting Process ◽  
Casting Method ◽  
Glass Substrates ◽  
Conductive Films ◽  
Casting Technology

This paper reports the fabrication and characterization of (Bi0.48Sb1.52)Te3 thick films using a tape casting process on glass substrates. A slurry of thermoelectric (Bi0.48Sb1.52)Te3 was developed and cured thick films were annealed in a vacuum chamber at 500–600 °C. The microstructure of these films was analyzed, and the Seebeck coefficient and electric conductivity were tested. It was found that the subsequent annealing process must be carefully designed to achieve good thermoelectric properties of these samples. Conductive films were obtained after annealing and led to acceptable thermoelectric performance. While the properties of these initial materials are not at the level of bulk materials, this work demonstrates that the low-cost tape casting technology is promising for fabricating thermoelectric modules for energy conversion.

Fabrication of PVDF–HFP-based microporous membranes by the tape casting method as a separator for flexible Li-ion batteries

2021 ◽  
Vol 44 (2) ◽  
Author(s):  
Prerna Chaturvedi ◽  
Amarsingh Bhabu Kanagaraj ◽  
Amani Alhammadi ◽  
Hamda Al Shibli ◽  
Daniel S Choi
Keyword(s):  
Tape Casting ◽  
Microporous Membranes ◽  
Li Ion Batteries ◽  
Casting Method ◽  
Li Ion

Manufacturing Processes of Solid Oxide Fuel Cell Components

2007 ◽  
Vol 336-338 ◽  
pp. 498-501
Author(s):  
Xian Feng Jiang ◽  
Min Fang Han ◽  
Su Ping Peng
Keyword(s):  
Fuel Cell ◽  
Solid Oxide Fuel Cell ◽  
Screen Printing ◽  
Sol Gel ◽  
Tape Casting ◽  
Solid Oxide ◽  
Oxide Fuel ◽  
Cell Components ◽  
One Step ◽  
Made In

The all processes for manufacturing materials parts of solid oxide fuel cell (SOFC) are discussed in the paper. The films are made in one step by the ways of APS, VPS, EVD, which are usually used to produce the electrolyte and interconnect. The films are thin and good gas-resistance, but with relatively high cost. All parts of SOFC are made by the following ways, such as sol-gel, tape casting, tape calendaring and screen printing, which are suitable for manufacturing samples in industry with the cheapest process by co-sintered together ways.

Fabrication and rheological behavior of tape‐casting slurry for ultra‐thin multilayer transparent ceramics

2019 ◽  
Vol 17 (3) ◽  
pp. 1255-1263 ◽  
Author(s):  
Han Zhao ◽  
Fei Tang ◽  
Yongzhen Xie ◽  
Zicheng Wen ◽  
Kangzhen Tian ◽  
...  
Keyword(s):  
Rheological Behavior ◽  
Tape Casting ◽  
Transparent Ceramics
Sign in / Sign up

Export Citation Format

Share Document