Characterization of Cured Epoxy Powder Coatings by Solvent Absorption

1982 ◽  
pp. 199-212 ◽  
Author(s):  
W. A. ROMANCHICK ◽  
J. F. GEIBEL
Keyword(s):  
Powder Coatings ◽  
Solvent Absorption

On the combined use of scratch tests and CLA profilometry for the characterization of polyester powder coatings: Influence of scratch load and speed

2008 ◽  
Vol 254 (22) ◽  
pp. 7198-7214 ◽  
Author(s):  
M. Barletta ◽  
A. Gisario ◽  
L. Lusvarghi ◽  
G. Bolelli ◽  
G. Rubino
Keyword(s):  
Powder Coatings ◽  
Combined Use ◽  
Scratch Tests

On the synthesis and characterization of new low temperature curing powder coatings cured with radiation

1998 ◽  
Vol 70 (9) ◽  
pp. 57-62 ◽  
Author(s):  
Mats Johansson ◽  
Henrik Falkén ◽  
Axel Irestedt ◽  
Anders Hult
Keyword(s):  
Low Temperature ◽  
Synthesis And Characterization ◽  
Powder Coatings

scholarly journals Promising Potential of Eugenol (Clove) Based Organic Membrane for Polymer Electrolyte Membrane Fuel Cell

2021 ◽  
Vol 2117 (1) ◽  
pp. 012037
Author(s):  
E C Muliawati ◽  
A Budianto ◽  
A Hamid
Keyword(s):  
Fuel Cell ◽  
Polymer Electrolyte ◽  
Polymer Electrolyte Membrane ◽  
Proton Conductor ◽  
Exchange Capacity ◽  
Methanol Permeability ◽  
Ion Exchange Capacity ◽  
Electrolyte Membrane ◽  
Solvent Absorption

Abstract Fuel cell is one of alternative method to replace fossil fuel energy. The important component of fuel cell is a membrane that used for separating cathode and anode also as a proton conductor. The purpose of this research is to produce polymer electrolyte membrane from poly (eugenol sulfonate) (PES) as polymer matrix, characterize the resulting membrane analysis using ionic properties analysis by calculating ionic conductivity using impedance spectroscopy, ion exchange capacity (IEC), solvent absorption analysis by calculating water uptake and methanol permeability, and studying mechanism Proton transport that occurs on the membrane. This research was initiated by making polymer of PES, and then fabrication and characterization of electrolytic polymer membrane. The formed membrane has an optimal proton conductivity of 0.00095 S.cm-1 with PES composition of 22% (wt).

scholarly journals Characterization of Flow Properties of Powder Coatings Used in the Automotive Industry

2004 ◽  
Vol 22 (0) ◽  
pp. 94-106 ◽  
Author(s):  
Cyril Conesa ◽  
Khashayar Saleh ◽  
Aline Thomas ◽  
Pierre Guigon ◽  
Nicolas Guillot
Keyword(s):  
Automotive Industry ◽  
Powder Coatings ◽  
Flow Properties

Synthesis and characterization of carboxyl group-containing acrylic resin for powder coatings

2008 ◽  
Vol 62 (2) ◽  
pp. 179-182 ◽  
Author(s):  
Zhengfa Zhou ◽  
Weibing Xu ◽  
Jixian Fan ◽  
Fengmei Ren ◽  
Chunlei Xu
Keyword(s):  
Acrylic Resin ◽  
Synthesis And Characterization ◽  
Carboxyl Group ◽  
Powder Coatings

Characterization of infrared absorption by powder coatings on steel panels

1999 ◽  
Vol 71 (2) ◽  
pp. 71-84
Author(s):  
A. L. Stewart ◽  
W. W. Carr ◽  
V. A. Williamson ◽  
E. G. McFarland ◽  
M. R. Johnson ◽  
...  
Keyword(s):  
Infrared Absorption ◽  
Powder Coatings ◽  
Steel Panels

Deposition and Characterization of CoCrAlY Coatings by Multi-Chamber Detonation Sprayer

2015 ◽  
Vol 752-753 ◽  
pp. 11-16
Author(s):  
M.G. Kovaleva ◽  
Yu.N. Tyurin ◽  
N.J. Vasilik ◽  
O.V. Kolisnichenko ◽  
M.S. Prozorova ◽  
...  
Keyword(s):  
Nickel Base Superalloy ◽  
Dense Layer ◽  
Micro Hardness ◽  
Powder Coatings ◽  
Hardness Tester ◽  
Nickel Base ◽  
Xrd Techniques ◽  
Base Superalloy

In this study, a multi-chamber detonation sprayer (MCDS) was applied for deposition of Co-Cr-Al-Y powder coatings (200-250 mm thick) on nickel base superalloy JS6U (Russia). Powder Co-25Cr-11Al-1Y (d(0.1): 6.6 μm, d(0.5): 62.7 μm, d(0.9): 123,4 μm) was used to deposit of a coatings. The coatings microstructures and phase compositions were characterized using SEM, OM and XRD techniques. Measurement of the microhardness of samples was done with a micro-hardness tester DM – 8B using a Vickers’s indenter with load on of 0.1 N. It was established that MCDS has provided the conditions for formation of a dense layer with porosity 0.05% and microhardness 600±50 HV0.1.

Sign in / Sign up

Export Citation Format

Share Document