Three-dimensional seismic refraction tomography: A comparison of two methods applied to data from the Faeroe Basin

1998 ◽  
Vol 103 (B4) ◽  
pp. 7187-7210 ◽  
Author(s):  
Colin A. Zelt ◽  
Penny J. Barton
Keyword(s):  
Seismic Refraction ◽  
Three Dimensional ◽  
Refraction Tomography

scholarly journals Electric resistivity and seismic refraction tomography, a challenging joint underwater survey at Äspö Hard Rock Laboratory

2016 ◽  
Author(s):  
Mathias Ronczka ◽  
Kristofer Hellman ◽  
Thomas Günther ◽  
Roger Wisen ◽  
Torleif Dahlin
Keyword(s):  
Nuclear Power ◽  
Hard Rock ◽  
Seismic Refraction ◽  
Three Dimensional ◽  
Test Site ◽  
Fracture Zones ◽  
Rock Laboratory ◽  
Refraction Tomography ◽  
Local Point ◽  
General Test

Abstract. Tunnelling below water passages is a challenging task in terms of planning, pre-investigation and construction. Fracture zones in the underlying bedrock lead to low rock quality and thus reduced stability. For natural reasons they tend to be more frequent at water passages. Ground investigations that provide information of the subsurface are necessary prior to the construction phase, but can be logistically difficult. Geophysics can help close the gaps between local point information and produce subsurface images. An approach that combines seismic refraction tomography and electrical resistivity tomography has been tested at the Äspö Hard Rock Laboratory (HRL). The aim was to detect fracture zones in a well-known but logistically and, from a measuring perspective, challenging area. The presented surveys cover a water passage along a part of a tunnel that connects surface facilities with an underground test laboratory. The tunnel is approximately 100 m below and 20 m east of the survey line and gives evidence for one major and several minor fracture zones. The geological and general test site conditions, e.g. with strong powerline noise from the nearby nuclear power plant, are challenging for geophysical measurements. Co-located positions for seismic and ERT sensors and source positions are used on the 450 m long underwater section of the 700 m long profile. Because of a large transition zone that appeared in the ERT result and the missing coverage of the seismic data, fracture zones at the southern and northern part of the underwater passage cannot be detected by separated inversion. A simple synthetic study shows significant three dimensional artefacts corrupting the ERT model that have to be taken into account while interpreting the results. A structural coupling cooperative inversion approach is able to image the northern fracture zone successfully. In addition, previously unknown sedimentary deposits with a significant large thickness are detected in the otherwise unusually well documented geological environment. The results significantly improve imaging of some geologic features, which would have been not detected or misinterpreted otherwise, and combines the images by means of cluster analysis to a conceptual subsurface model.

scholarly journals Electric resistivity and seismic refraction tomography: a challenging joint underwater survey at Äspö Hard Rock Laboratory

Solid Earth ◽  
2017 ◽  
Vol 8 (3) ◽  
pp. 671-682 ◽  
Author(s):  
Mathias Ronczka ◽  
Kristofer Hellman ◽  
Thomas Günther ◽  
Roger Wisén ◽  
Torleif Dahlin
Keyword(s):  
Nuclear Power ◽  
Hard Rock ◽  
Seismic Refraction ◽  
Three Dimensional ◽  
Test Site ◽  
Fracture Zones ◽  
Rock Laboratory ◽  
Refraction Tomography ◽  
Local Point ◽  
General Test

Abstract. Tunnelling below water passages is a challenging task in terms of planning, pre-investigation and construction. Fracture zones in the underlying bedrock lead to low rock quality and thus reduced stability. For natural reasons, they tend to be more frequent at water passages. Ground investigations that provide information on the subsurface are necessary prior to the construction phase, but these can be logistically difficult. Geophysics can help close the gaps between local point information by producing subsurface images. An approach that combines seismic refraction tomography and electrical resistivity tomography has been tested at the Äspö Hard Rock Laboratory (HRL). The aim was to detect fracture zones in a well-known but logistically challenging area from a measuring perspective. The presented surveys cover a water passage along part of a tunnel that connects surface facilities with an underground test laboratory. The tunnel is approximately 100 m below and 20 m east of the survey line and gives evidence for one major and several minor fracture zones. The geological and general test site conditions, e.g. with strong power line noise from the nearby nuclear power plant, are challenging for geophysical measurements. Co-located positions for seismic and ERT sensors and source positions are used on the 450 m underwater section of the 700 m profile. Because of a large transition zone that appeared in the ERT result and the missing coverage of the seismic data, fracture zones at the southern and northern parts of the underwater passage cannot be detected by separated inversion. Synthetic studies show that significant three-dimensional (3-D) artefacts occur in the ERT model that even exceed the positioning errors of underwater electrodes. The model coverage is closely connected to the resolution and can be used to display the model uncertainty by introducing thresholds to fade-out regions of medium and low resolution. A structural coupling cooperative inversion approach is able to image the northern fracture zone successfully. In addition, previously unknown sedimentary deposits with a significantly large thickness are detected in the otherwise unusually well-documented geological environment. The results significantly improve the imaging of some geologic features, which would have been undetected or misinterpreted otherwise, and combines the images by means of cluster analysis into a conceptual subsurface model.

Integration of Multi-geophysical Approaches to Identify Potential Pathways of Heavy Metals Contamination - A Case Study in Zeida, Morocco

2020 ◽  
Vol 25 (3) ◽  
pp. 415-423
Author(s):  
Ahmed Lachhab ◽  
El Mehdi Benyassine ◽  
Mohamed Rouai ◽  
Abdelilah Dekayir ◽  
Jean C. Parisot ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Seismic Velocity ◽  
Seismic Refraction ◽  
Geophysical Methods ◽  
Low Frequency ◽  
Electrical Current ◽  
P Wave ◽  
Low Resistivity ◽  
Refraction Tomography ◽  
Geophysical Surveys

The tailings of Zeida's abandoned mine are found near the city of Midelt, in the middle of the high Moulouya watershed between the Middle and the High Atlas of Morocco. The tailings occupy an area of about 100 ha and are stored either in large mining pit lakes with clay-marl substratum or directly on a heavily fractured granite bedrock. The high contents of lead and arsenic in these tailings have transformed them into sources of pollution that disperse by wind, runoff, and seepage to the aquifer through faults and fractures. In this work, the main goal is to identify the pathways of contaminated water with heavy metals and arsenic to the local aquifers, water ponds, and Moulouya River. For this reason, geophysical surveys including electrical resistivity tomography (ERT), seismic refraction tomography (SRT) and very low-frequency electromagnetic (VLF-EM) methods were carried out over the tailings, and directly on the substratum outside the tailings. The result obtained from combining these methods has shown that pollutants were funneled through fractures, faults, and subsurface paleochannels and contaminated the hydrological system connecting groundwater, ponds, and the river. The ERT profiles have successfully shown the location of fractures, some of which extend throughout the upper formation to depths reaching the granite. The ERT was not successful in identifying fractures directly beneath the tailings due to their low resistivity which inhibits electrical current from propagating deeper. The seismic refraction surveys have provided valuable details on the local geology, and clearly identified the thickness of the tailings and explicitly marked the boundary between the Triassic formation and the granite. It also aided in the identification of paleochannels. The tailings materials were easily identified by both their low resistivity and low P-wave velocity values. Also, both resistivity and seismic velocity values rapidly increased beneath the tailings due to the compaction of the material and lack of moisture and have proven to be effective in identifying the upper limit of the granite. Faults were found to lie along the bottom of paleochannels, which suggest that the locations of these channels were caused by these same faults. The VLF-EM surveys have shown tilt angle anomalies over fractured areas which were also evinced by low resistivity area in ERT profiles. Finally, this study showed that the three geophysical methods were complementary and in good agreement in revealing the pathways of contamination from the tailings to the local aquifer, nearby ponds and Moulouya River.

scholarly journals Geophysical investigations for stability and safety mitigation of regional crude-oil pipeline near abandoned coal mines

2021 ◽  
Vol 18 (1) ◽  
pp. 145-162
Author(s):  
B Butchibabu ◽  
Prosanta Kumar Khan ◽  
P C Jha
Keyword(s):  
High Resolution ◽  
Crude Oil ◽  
Seismic Refraction ◽  
High Resolution Imaging ◽  
Weak Zone ◽  
Near Surface ◽  
Oil Pipeline ◽  
Refraction Tomography ◽  
Geophysical Investigations ◽  
Resolution Imaging

Abstract This study aims for the protection of a crude-oil pipeline, buried at a shallow depth, against a probable environmental hazard and pilferage. Both surface and borehole geophysical techniques such as electrical resistivity tomography (ERT), ground penetrating radar (GPR), surface seismic refraction tomography (SRT), cross-hole seismic tomography (CST) and cross-hole seismic profiling (CSP) were used to map the vulnerable zones. Data were acquired using ERT, GPR and SRT along the pipeline for a length of 750 m, and across the pipeline for a length of 4096 m (over 16 profiles of ERT and SRT with a separation of 50 m) for high-resolution imaging of the near-surface features. Borehole techniques, based on six CSP and three CST, were carried out at potentially vulnerable locations up to a depth of 30 m to complement the surface mapping with high-resolution imaging of deeper features. The ERT results revealed the presence of voids or cavities below the pipeline. A major weak zone was identified at the central part of the study area extending significantly deep into the subsurface. CSP and CST results also confirmed the presence of weak zones below the pipeline. The integrated geophysical investigations helped to detect the old workings and a deformation zone in the overburden. These features near the pipeline produced instability leading to deformation in the overburden, and led to subsidence in close vicinity of the concerned area. The area for imminent subsidence, proposed based on the results of the present comprehensive geophysical investigations, was found critical for the pipeline.

Application of geophysical methods for the investigation of the large gravitational mass movement of Séchilienne, France

2005 ◽  
Vol 42 (4) ◽  
pp. 1105-1115 ◽  
Author(s):  
O Meric ◽  
S Garambois ◽  
D Jongmans ◽  
M Wathelet ◽  
J L Chatelain ◽  
...  
Keyword(s):  
Rock Mass ◽  
Mass Movement ◽  
Seismic Refraction ◽  
Geophysical Methods ◽  
Time Lapse ◽  
Gravitational Mass ◽  
Electrical Tomography ◽  
Refraction Tomography ◽  
Geophysical Surveys ◽  
Geophysical Techniques

Several geophysical techniques (electromagnetic profiling, electrical tomography, seismic refraction tomography, and spontaneous potential and seismic noise measurement) were applied in the investigation of the large gravitational mass movement of Séchilienne. France. The aim of this study was to test the ability of these methods to characterize and delineate the rock mass affected by this complex movement in mica schists, whose lateral and vertical limits are still uncertain. A major observation of this study is that all the zones strongly deformed (previously and at present) by the movement are characterized by high electrical resistivity values (>3 kΩ·m), in contrast to the undisturbed mass, which exhibits resistivity values between a few hundred and 1 kΩ·m. As shown by the surface observations and the seismic results, this resistivity increase is due to a high degree of fracturing associated with the creation of air-filled voids inside the mass. Other geophysical techniques were tested along a horizontal transect through the movement, and an outstanding coherency appeared between the geophysical anomalies and the displacement rate curve. These preliminary results illustrate the benefits of combined geophysical techniques for characterizing the rock mass involved in the movement. Results also suggest that monitoring the evolution of the rock mass movement with time-lapse geophysical surveys could be beneficial.Key words: gravitational movement, geophysical methods, Séchilienne.

scholarly journals Applying the Seismic Refraction Tomography for Site Characterization

2013 ◽  
Vol 5 ◽  
pp. 227-231 ◽  
Author(s):  
I.N. Azwin ◽  
Rosli Saad ◽  
M. Nordiana
Keyword(s):  
Seismic Refraction ◽  
Site Characterization ◽  
Refraction Tomography

GEOTECHNICAL PARAMETERS STUDY USING SEISMIC REFRACTION TOMOGRAPHY

2016 ◽  
Vol 78 (8-6) ◽  
Author(s):  
Rose Nadia ◽  
Rosli Saad ◽  
Nordiana Muztaza ◽  
Nur Azwin Ismail ◽  
Mohd Mokhtar Saidin
Keyword(s):  
Parameter Estimation ◽  
Seismic Refraction ◽  
Standard Penetration Test ◽  
P Wave ◽  
Cohesive Soils ◽  
Penetration Test ◽  
Geotechnical Parameters ◽  
Wave Velocities ◽  
Refraction Tomography ◽  
Loose Medium

In this study, correlation is made between seismic P-wave velocities (Vp) with standard penetration test (SPT-N) values to produce soil parameter estimation for engineering site applications. A seismic refraction tomography (SRT) line of 69 m length was spread across two boreholes with 3 m geophones spacing. The acquired data were processed using Firstpix, SeisOpt2D and surfer8 software. The Vp at particular depths were pinpointed and correlated with geotechnical parameters (SPT-N values) from the borehole records. The correlation between Vp and SPT-N values has been established. For cohesive soils, it is grouped into three categories according to consistencies; stiff, very stiff and hard, having velocity rangesof 575-314 m/s, 808-1483 m/s and 1735-2974 m/s, respectively. For non-cohesive soils, it is also divided into three categories based on the denseness as loose, medium dense and dense with Vp ranges of 528-622 m/s, 900-2846 m/s and 2876-2951 m/s, respectively

scholarly journals Landslide characterization using P- and S-wave seismic refraction tomography — The importance of elastic moduli

2016 ◽  
Vol 134 ◽  
pp. 64-76 ◽  
Author(s):  
S. Uhlemann ◽  
S. Hagedorn ◽  
B. Dashwood ◽  
H. Maurer ◽  
D. Gunn ◽  
...  
Keyword(s):  
Elastic Moduli ◽  
Seismic Refraction ◽  
S Wave ◽  
Refraction Tomography
Sign in / Sign up

Export Citation Format

Share Document