A super-stretchable and tough functionalized boron nitride/PEDOT:PSS/poly(N-isopropylacrylamide) hydrogel with self-healing, adhesion, conductive and photothermal activity

2019 ◽  
Vol 7 (14) ◽  
pp. 8204-8209 ◽  
Author(s):  
Shuai Cao ◽  
Xin Tong ◽  
Kun Dai ◽  
Qun Xu
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Self Healing

A new multifunctional f-BNNS/PEDOT:PSS/PNIPAM hydrogel with high mechanical properties has been successfully prepared.

Autonomous self-healing polyisoprene elastomers with high modulus and good toughness based on the synergy of dynamic ionic crosslinks and highly disordered crystals

2020 ◽  
Vol 11 (41) ◽  
pp. 6549-6558
Author(s):  
Yohei Miwa ◽  
Mayu Yamada ◽  
Yu Shinke ◽  
Shoichi Kutsumizu
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Self Healing ◽  
High Modulus ◽  
Disordered Crystals ◽  
Ionic Crosslinks

We designed a novel polyisoprene elastomer with high mechanical properties and autonomous self-healing capability at room temperature facilitated by the coexistence of dynamic ionic crosslinks and crystalline components that slowly reassembled.

Structure and properties of compact articles from high-alloyed iron powder with adding of boron nitride

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Grain Boundary ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Operating Conditions ◽  
Structure And Properties ◽  
Steam Turbines ◽  
Friction Forces ◽  
Wide Range

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.

Boron nitride for modification of rubber based on isoprene elastomer

2020 ◽  
pp. 105-112
Author(s):  
K. S. Zhansakova ◽  
E. N. Eremin ◽  
G. S. Russkikh ◽  
O. V. Kropotin
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Gradual Increase ◽  
Physical And Mechanical Properties ◽  
Curing Time ◽  
Cross Link ◽  
Start Time ◽  
Link Density ◽  
Cross Link Density ◽  
Isoprene Rubber

The work studies vulcanization characteristics of elastomers based on isoprene rubber filled with carbon black N330 and boron nitride (BN). The influence of the boron nitride (BN) concentration on technological, dynamic, physical and mechanical properties of elastomers has been researched. The application of boron nitride for producing rubber with good properties has been considered. With a gradual increase of the inert filler BN concentration up to 35%, a decrease in the curing rate by 33% and polymer cross-link density by 26% is observed. Moreover, the start time of vulcanization increases by almost 300%, the optimal curing time by 200%.

Polypyrrole/PU hybrid hydrogels: electrically conductive and fast self-healing for the potential application in body-monitor sensor

2021 ◽  
Author(s):  
Zhanyu Jia ◽  
Guangyao Li ◽  
Juan Wang ◽  
shouhua Su ◽  
Jie Wen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Potential Application ◽  
Self Healing ◽  
Electrically Conductive ◽  
Sensor Application ◽  
Hybrid Hydrogels ◽  
Health Monitor

Conductivity, self-healing and moderate mechanical properties are necessary for multifunctional hydrogels which have great potential in health-monitor sensor application. However, the combination of electrical conductivity, self-healing and good mechanical properties...

Self-healing, Highly Elastic and Amphiphilic Silicone-based Polyurethane for Antifouling Coatings

2021 ◽  
Author(s):  
Xiaobin Lin ◽  
Qingyi Xie ◽  
Chunfeng Ma ◽  
Guangzhao Zhang
Keyword(s):  
Mechanical Properties ◽  
Silicone Elastomer ◽  
Self Healing ◽  
Fouling Resistance ◽  
The Poor ◽  
Antifouling Coatings ◽  
Fouling Release

Silicone elastomer coatings have attracted increasing attention owing to its eco-friendly nature, excellent fouling release ability and drag-reducing property. However, the poor mechanical properties and lack of fouling resistance limits...

The preparation of hydrogels with highly efficient self-healing and excellent mechanical properties

2021 ◽  
Vol 329 ◽  
pp. 115581
Author(s):  
Chaoxian Chen ◽  
Zhongcun Li ◽  
Siwen Chen ◽  
Lingzhi Kong ◽  
Zhihao Guo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Self Healing ◽  
Highly Efficient

scholarly journals The Effect of Superabsorbent Polymers on the Microstructure and Self-Healing Properties of Cementitious-Based Composite Materials

2021 ◽  
Vol 11 (2) ◽  
pp. 700
Author(s):  
Irene A. Kanellopoulou ◽  
Ioannis A. Kartsonakis ◽  
Costas A. Charitidis
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Hybrid Structure ◽  
The Self ◽  
Self Healing ◽  
Cementitious Composite ◽  
Superabsorbent Polymers ◽  
Porosity Reduction ◽  
Environment Control ◽  
The Impact

Cementitious structures have prevailed worldwide and are expected to exhibit further growth in the future. Nevertheless, cement cracking is an issue that needs to be addressed in order to enhance structure durability and sustainability especially when exposed to aggressive environments. The purpose of this work was to examine the impact of the Superabsorbent Polymers (SAPs) incorporation into cementitious composite materials (mortars) with respect to their structure (hybrid structure consisting of organic core—inorganic shell) and evaluate the microstructure and self-healing properties of the obtained mortars. The applied SAPs were tailored to maintain their functionality in the cementitious environment. Control and mortar/SAPs specimens with two different SAPs concentrations (1 and 2% bwoc) were molded and their mechanical properties were determined according to EN 196-1, while their microstructure and self-healing behavior were evaluated via microCT. Compressive strength, a key property for mortars, which often degrades with SAPs incorporation, in this work, practically remained intact for all specimens. This is coherent with the porosity reduction and the narrower range of pore size distribution for the mortar/SAPs specimens as determined via microCT. Moreover, the self-healing behavior of mortar-SAPs specimens was enhanced up to 60% compared to control specimens. Conclusively, the overall SAPs functionality in cementitious-based materials was optimized.

Sign in / Sign up

Export Citation Format

Share Document