Experimental and Numerical Heat Transfer Investigation of Impingement Jet Nozzle Position in Concave Double-Wall Cooling Structures

2021 ◽  
pp. 1-14
Author(s):  
Edward Wright ◽  
Abdallah Ahmed ◽  
Yuying Yan ◽  
John Maltson ◽  
Lynda Arisso Lopez
Keyword(s):  
Heat Transfer ◽  
Numerical Heat Transfer ◽  
Impingement Jet ◽  
Nozzle Position ◽  
Jet Nozzle ◽  
Double Wall

Numerical Investigation of a Crossflow Jet in a Rectangular Microchannel

2013 ◽  
Vol 284-287 ◽  
pp. 849-853
Author(s):  
Kok Cheong Wong
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Numerical Study ◽  
Three Dimensional ◽  
Horizontal Flow ◽  
Transfer Performance ◽  
Rectangular Microchannel ◽  
Transverse Jet ◽  
Nozzle Position ◽  
Jet Nozzle

The present numerical study is conducted in three dimensional to investigate the crossflow of an external round jet and a horizontal stream of microchannel flow. The results of heat transfer performance for the cases with and without transverse jet are compared. The patterns of different crossflow jet were analyzed to understand the flow and heat transfer characteristics. The effect of jet nozzle position on the heat transfer is investigated. Generally, the heat transfer performance increases with the jet Reynolds number. However, some cases of weak jet are found to cause lower heat transfer rate relative to the case without external jet. When vertical weak jet encounter strong horizontal flow, the horizontal flow is dominant that the jet cannot reach the microchannel bottom wall but imposes resistance to the horizontal flow. The investigation on the jet nozzle location shows that the jet nozzle location closer to the channel inlet gives better heat transfer performance.

Louver and effusion cooling heat transfer for a double wall effusion plate with impingement jet array coolant supply

2021 ◽  
Vol 168 ◽  
pp. 120861
Author(s):  
Sneha Reddy Vanga ◽  
Phillip M. Ligrani ◽  
Joseph Knox ◽  
Federico Liberatore ◽  
Rajeshriben Patel ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Impingement Jet ◽  
Double Wall ◽  
Jet Array

Experimental and numerical heat transfer investigation of an impingement jet array with V-ribs on the target plate and on the impingement plate

2017 ◽  
Vol 68 ◽  
pp. 126-138 ◽  
Author(s):  
Lingling Chen ◽  
Robin G.A. Brakmann ◽  
Bernhard Weigand ◽  
Jose Rodriguez ◽  
Michael Crawford ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Target Plate ◽  
Numerical Heat Transfer ◽  
Impingement Jet ◽  
Impingement Plate ◽  
Jet Array

WINGLET-PAIR TARGET SURFACE ROUGHNESS INFLUENCES ON IMPINGEMENT JET ARRAY HEAT TRANSFER

2019 ◽  
Vol 26 (1) ◽  
pp. 15-35 ◽  
Author(s):  
Phillip Ligrani ◽  
Patrick McInturff ◽  
Masaaki Suzuki ◽  
Chiyuki Nakamata
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
Target Surface ◽  
Impingement Jet ◽  
Jet Array

scholarly journals Assessment of TiO2 Nanoconcentration and Twin Impingement Jet of Heat Transfer Enhancement—A Statistical Approach Using Response Surface Methodology

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 595
Author(s):  
Mahir Faris Abdullah ◽  
Rozli Zulkifli ◽  
Hazim Moria ◽  
Asmaa Soheil Najm ◽  
Zambri Harun ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Tio2 Nanoparticle ◽  
Experimental Results ◽  
Improvement Rate ◽  
Design Expert ◽  
Impingement Jet

Impinging jets are considered to be a well-known technique that offers high local heat transfer rates. No correlation could be established in the literature between the significant parameters and the Nusselt number, and investigation of the interactions between the correlated factors has not been conducted before. An experimental analysis based on the twin impingement jet mechanism was achieved to study the heat transfer rate pertaining to the surface plate. In the current paper, four influential parameters were studied: the spacing between nozzles, velocity, concentration of Nano solution coating and nozzle-plate distance, which are considered to be effective parameters for the thermal conductivity and the heat transfer coefficient of TiO2 nanoparticle, an X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis were done, which highlighted the structure and showed that the nanosolution coated the surface homogenously. Moreover, a comparison was done for the experimental results with that of the predicted responses generated by the Design Expert software, Version 7 User’s Guide, USA. A response surface methodology (RSM) was employed to improve a mathematical model by accounting for a D-optimal design. In addition, the analysis of variance (ANOVA) was employed for testing the significance of the models. The maximum Nu of 91.47, where H = S = 1 cm; Reynolds number of 17,000, and TiO2 nanoparticle concentration of 0.5% M. The highest improvement rate in Nusselt was about 26%, achieved with TiO2 Nanoparticle, when S = 3 cm, H = 6 cm and TiO2 nanoparticle = 0.5 M. Furthermore, based on the statistical analysis, the expected values were found to be in satisfactory agreement with that of the empirical data, which was conducted by accounting for the proposed models’ excellent predictability. Multivariate approaches are very useful for researchers, as well as for applications in industrial processes, as they lead to increased efficiency and reduced costs, so the presented results of this work could encourage the overall uses of multivariate methods in these fields. Hypotheses: A comparison was done for the predicted responses generated by the Design Expert software with the experimental results and then studied to verify the following hypotheses: ► Preparation of three concentrations of TiO2 nanosolution was done and studied. ► The heat transfer rate could be increased by surface coating with TiO2 nanoparticle. ► The heat transfer could be improved by the impingement jet technique with suitable adjustments.

Effects of alternating elliptical chamber on jet impingement heat transfer in vane leading edge under different cross-flow conditions

2021 ◽  
pp. 1-17
Author(s):  
K. Xiao ◽  
J. He ◽  
Z. Feng
Keyword(s):  
Heat Transfer ◽  
Velocity Ratio ◽  
Cross Flow ◽  
Leading Edge ◽  
Longitudinal Vortices ◽  
Impingement Jet ◽  
Flow And Heat Transfer ◽  
Impingement Heat Transfer ◽  
Cross Flow Velocity ◽  
The Cross

ABSTRACT This paper proposes an alternating elliptical impingement chamber in the leading edge of a gas turbine to restrain the cross flow and enhance the heat transfer, and investigates the detailed flow and heat transfer characteristics. The chamber consists of straight sections and transition sections. Numerical simulations are performed by solving the three-dimensional (3D) steady Reynolds-Averaged Navier–Stokes (RANS) equations with the Shear Stress Transport (SST) k– $\omega$ turbulence model. The influences of alternating the cross section on the impingement flow and heat transfer of the chamber are studied by comparison with a smooth semi-elliptical impingement chamber at a cross-flow Velocity Ratio (VR) of 0.2 and Temperature Ratio (TR) of 1.00 in the primary study. Then, the effects of the cross-flow VR and TR are further investigated. The results reveal that, in the semi-elliptical impingement chamber, the impingement jet is deflected by the cross flow and the heat transfer performance is degraded. However, in the alternating elliptical chamber, the cross flow is transformed to a pair of longitudinal vortices, and the flow direction at the centre of the cross section is parallel to the impingement jet, thus improving the jet penetration ability and enhancing the impingement heat transfer. In addition, the heat transfer in the semi-elliptical chamber degrades rapidly away from the stagnation region, while the longitudinal vortices enhance the heat transfer further, making the heat transfer coefficient distribution more uniform. The Nusselt number decreases with increase of VR and TR for both the semi-elliptical chamber and the alternating elliptical chamber. The alternating elliptical chamber enhances the heat transfer and moves the stagnation point up for all VR and TR, and the heat transfer enhancement is more obvious at high cross-flow velocity ratio.

scholarly journals Time Averaged and Fluctuating Heat Transfer Measurements in an Atomising Mist Jet Nozzle

2009 ◽  
Author(s):  
Oisn F. P. Lyons ◽  
Darina B. Murray ◽  
Gerard Byrne ◽  
Tim Persoons
Keyword(s):  
Heat Transfer ◽  
Internal Structure ◽  
Research Group ◽  
Single Phase ◽  
Water Mist ◽  
Phase Behaviour ◽  
Heat Transfer Characteristics ◽  
Air Jets ◽  
Mist Flow ◽  
Jet Nozzle

Much is already known about the heat transfer characteristics of impinging air jets, and they are widely used in many engineering applications. There currently exist many correlations describing such characteristics. However, the complex internal structure of many nozzles can lead these to produce results which deviate from those predicted by correlations. One such nozzle is currently used in this research group to produce a water mist flow and this paper describes the experimental characteristics of its single phase behaviour.

Sign in / Sign up

Export Citation Format

Share Document