Cadmium accumulation in rice straws and derived biochars as affected by metal exposure, soil types and rice genotypes

Five phosphorus rates (0, 5, 10, 20 and 30 kg P/ha) were tested with four rice genotypes in Boro (BRRI dhan36, BRRI dhan45, EH1 and EH2) and T. Aman (BRRI dhan30, BRRI dhan49, EH1 and EH2) season. Phosphorus rates did not influence grain yield irrespective of varieties in T. Aman season while in Boro season P response was observed among the P rates. Application of P @ 10 kg/ha significantly increased the grain yield. But when P was applied @ 20 and 30 kg P/ha, the grain yield difference was not significant. The optimum and economic rate of P for T. Aman was 20 kg P/ha but in Boro rice the optimum and economic doses of P were 22 and 30 kg/ha, respectively. Hybrid entries (EH1 and EH2) used P more efficiently than inbred varieties. A negative P balance was observed up to 10 kg P/ha. Key words: Response; Phosphorus fertilizer; Inbred; Hybrid rice DOI: http://dx.doi.org/10.3329/dujbs.v19i2.8962 DUJBS 2010; 19(2): 181-187

Download Full-text

Molecular Characterization and Genetic Diversity Study in F3 Population of Rice

Progressive Agriculture ◽

10.3329/pa.v20i1-2.16839 ◽

2013 ◽

Vol 20 (1-2) ◽

pp. 1-8

Author(s):

MM Rahman ◽

L Rahman ◽

SN Begum ◽

F Nur

Keyword(s):

Genetic Distance ◽

Gene Diversity ◽

Random Amplified Polymorphic Dna ◽

Molecular Genetic ◽

Molecular Genetic Analysis ◽

Polymorphic Loci ◽

Rice Genotypes ◽

High Level ◽

Genetic Diversity Study ◽

Diversity Study

Random Amplified Polymorphic DNA (RAPD) assay was initiated for molecular genetic analysis among 13 F3 rice lines and their parents. Four out of 15 decamer random primers were used to amplify genomic DNA and the primers yielded a total of 41 RAPD markers of which 37 were considered as polymorphic with a mean of 9.25 bands per primer. The percentage of polymorphic loci was 90.24. The highest percentage of polymorphic loci (14.63) and gene diversity (0.0714) was observed in 05-6 F3 line and the lowest polymorphic loci (0.00) and gene diversity (0.00) was found in 05-12 and 05-15 F3 lines. So, relatively high level of genetic variation was found in 05-6 F3 line and it was genetically more diverse compared to others. The average co-efficient of gene differentiation (GST) and gene flow (Nm) values across all the loci were 0.8689 and 0.0755, respectively. The UPGMA dendrogram based on the Neis genetic distance differentiated the rice genotypes into two main clusters: PNR-519, 05-19, 05-14, 05-12 and 05-17 grouped in cluster 1. On the other hand, Baradhan, 05-9, 05-13, 05-11, 05-5, 05-6, 05-1, 05-4, 05-15 and 05-25 were grouped in cluster 2. The highest genetic distance (0.586) was found between 05-4 and 05-17 F3 lines and they remain in different cluster.DOI: http://dx.doi.org/10.3329/pa.v20i1-2.16839 Progress. Agric. 20(1 & 2): 1 8, 2009

Download Full-text

Screening of rice genotypes for resistance to the brown planthopper, Nilaparvata lugens Stål

Cereal Research Communications ◽

10.1556/crc.2012.0001 ◽

2012 ◽

Vol 40 (4) ◽

pp. 502-508 ◽

Cited By ~ 1

Author(s):

M. P. Ali ◽

Salem S. Alghamdi ◽

M. A. Begum ◽

A. B. M. Anwar Uddin ◽

M. Z. Alam ◽

...

Keyword(s):

Brown Planthopper ◽

Nilaparvata Lugens ◽

Rice Genotypes

Download Full-text

Abrasive wear of polymer/steel gear drives

Progress in Agricultural Engineering Sciences ◽

10.1556/progress.4.2008.1 ◽

2008 ◽

Vol 4 (1) ◽

pp. 1-26

Author(s):

Gábor Kalácska

Keyword(s):

Wear Resistance ◽

Abrasive Wear ◽

Material Selection ◽

Solid Particles ◽

Soil Types ◽

General View ◽

Modern Engineering ◽

Clean Environment ◽

Engineering Polymers ◽

Plastic Gears

Research was performed on the friction, wear and efficiency of plastic gears made of modern engineering polymers and their composites both in a clean environment (adhesive sliding surfaces) and in an environment contaminated with solid particles and dust (abrasive), with no lubrication at all. The purpose is to give a general view about the results of abrasive wear tests including seven soil types as abrasive media. At the first stage of the research silicious sand was applied between the meshing gears and the wear of plastic and steel gears was evaluated and analyzed from the point of different material properties (elongation at break, hardness, yield stress, modulus of elasticity) and its combinations. The different correlations between the experienced wear and material features are also introduced. At the second stage of the project the abrasive sand was replaced with different physical soil types. The abrasive wear of gears is plotted in the function of soil types. The results highlight on the considerable role of physical soil types on abrasive wear resistance and the conclusions contain the detailed wear resistance. The results offer a new tribology database for the operation and maintenance of agricultural machines with the opportunity of a better material selection according to the dominant soil type. This can finally result longer lifetime and higher reliability of wearing plastic/steel parts.

Download Full-text

Effects of heavy metals on soil invertase enzyme activity in different soil types

Land Contamination & Reclamation ◽

10.2462/09670513.941 ◽

2010 ◽

Vol 18 (2) ◽

pp. 175-180

Author(s):

Rajesh K. Verma ◽

Dharam Veer Yadav ◽

Chandra Pal Singh ◽

Archna Suman ◽

Asha Gaur

Keyword(s):

Heavy Metals ◽

Enzyme Activity ◽

Soil Types

Download Full-text