The In-Situ Observation of microstructure, grain orientation evolution and its effect on crack propagation path in SAC305 under extreme temperature changes

2021 ◽  
Author(s):  
KeXin Xu ◽  
Xing Fu ◽  
Min Liu ◽  
ZhiWei Fu ◽  
Si Chen ◽  
...  
Keyword(s):  
Crack Propagation ◽  
Grain Orientation ◽  
Extreme Temperature ◽  
Propagation Path ◽  
In Situ Observation ◽  
Temperature Changes ◽  
Crack Propagation Path

An Alternative Technique to Evaluate Crack Propagation Path in Hyperelastic Materials

2012 ◽  
Vol 40 (1) ◽  
pp. 42-58 ◽  
Author(s):  
R. R. M. Ozelo ◽  
P. Sollero ◽  
A. L. A. Costa
Keyword(s):  
Constitutive Model ◽  
Crack Propagation ◽  
Experimental Tests ◽  
Growth Direction ◽  
Propagation Path ◽  
J Integral ◽  
Alternative Technique ◽  
Crack Propagation Path ◽  
Hyperelastic Materials ◽  
Material Constitutive Model

Abstract REFERENCE: R. R. M. Ozelo, P. Sollero, and A. L. A. Costa, “An Alternative Technique to Evaluate Crack Propagation Path in Hyperelastic Materials,” Tire Science and Technology, TSTCA, Vol. 40, No. 1, January–March 2012, pp. 42–58. ABSTRACT: The analysis of crack propagation in tires aims to provide safety and reliable life prediction. Tire materials are usually nonlinear and present a hyperelastic behavior. Therefore, the use of nonlinear fracture mechanics theory and a hyperelastic material constitutive model are necessary. The material constitutive model used in this work is the Mooney–Rivlin. There are many techniques available to evaluate the crack propagation path in linear elastic materials and estimate the growth direction. However, most of these techniques are not applicable to hyperelastic materials. This paper presents an alternative technique for modeling crack propagation in hyperelastic materials, based in the J-Integral, to evaluate the crack path. The J-Integral is an energy-based parameter and is applicable to nonlinear materials. The technique was applied using abaqus software and compared to experimental tests.

scholarly journals Crack Propagation Behavior of a Ni-Based Single-Crystal Superalloy during In Situ SEM Tensile Test at 1000 °C

Crystals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1047
Author(s):  
Wenxiang Jiang ◽  
Xiaoyi Ren ◽  
Jinghao Zhao ◽  
Jianli Zhou ◽  
Jinyao Ma ◽  
...  
Keyword(s):  
Crack Propagation ◽  
Tensile Test ◽  
Single Crystal ◽  
Crack Propagation Rate ◽  
Propagation Rate ◽  
Single Crystal Superalloy ◽  
Propagation Path ◽  
Propagation Behavior ◽  
Crack Propagation Behavior

An in situ scanning electron microscope (SEM) tensile test for Ni-based single-crystal superalloy was carried out at 1000 °C. The stress displacement was obtained, and the yield strength and tensile strength of the superalloy were 699 MPa and 826 MPa, respectively. The crack propagation process, consisting of Model I crack and crystallographic shearing crack, was determined. More interestingly, the crack propagation path and rate affected by eutectics was directly observed and counted. Results show that the coalescence of the primary crack and second microcrack at the interface of a γ/γ′ matrix and eutectics would make the crack propagation rate increase from 0.3 μm/s to 0.4 μm/s. On the other hand, crack deflection decreased the rate to 0.05 μm/s. Moreover, movement of dislocations in front of the crack was also analyzed to explain the different crack propagation behavior in the superalloy.

Prediction Method of Three‐Dimensional Crack Propagation Path Based on Deep Learning Application

2020 ◽  
pp. 2001043
Author(s):  
Junxia Wang ◽  
Yuanjie Zheng ◽  
Rong Luo ◽  
Jun Ma ◽  
Yingjie Peng ◽  
...  
Keyword(s):  
Deep Learning ◽  
Crack Propagation ◽  
Three Dimensional ◽  
Prediction Method ◽  
Propagation Path ◽  
Crack Propagation Path

scholarly journals Controlling the Crack Propagation Path of the Veil Interleaved Composite by Fusion-Bonded Dots

Polymers ◽  
2019 ◽  
Vol 11 (8) ◽  
pp. 1260 ◽  
Author(s):  
Guangchang Chen ◽  
Jindong Zhang ◽  
Gang Liu ◽  
Puhui Chen ◽  
Miaocai Guo
Keyword(s):  
Crack Propagation ◽  
Propagation Path ◽  
Mode I ◽  
Fiber Breakage ◽  
Fracture Path ◽  
Interlaminar Fracture ◽  
Crack Propagation Path ◽  
Pull Out ◽  
Continuous Carbon Fiber ◽  
The Veil

This study investigated the effect of the fusion-bonded dots of veil interleaves on the crack propagation path of the interlaminar fracture of continuous carbon fiber reinforced epoxy resin. Two thin fiber layers (i.e., nylon veil (NV) with fusion-bonded dots and Kevlar veil (KV) physically stacked by fibers) were used to toughen composites as interleaves. Result shows that the existence of fusion-bonded dots strongly influenced the crack propagation and changed the interlaminar fracture mechanism. The Mode I fracture path of the nylon veil interleaved composite (NVIC) could propagate in the plane where the dots were located, whereas the path of the Kevlar veil interleaved composite (KVIC) randomly deflected inside the interlayer without the pre-cracking of the dots. The improvement of Mode I toughness was mainly based on fiber bridging and the resulting fiber breakage and pull-out. Fiber breakage was often observed for NVIC, whereas fiber pull-out was the main mechanism for KVIC. For the Mode II fracture path, the fusion-bonded NV dots guided the fracture path largely deflected inside the interlayer, causing the breakage of tough nylon fibers. The fracture path of the physically stacked KVIC occurred at one carbon ply/interlayer interface and only slightly deflected at fiber overlapped regions. Moreover, the fiber pull-out was often observed.

Sign in / Sign up

Export Citation Format

Share Document