Notice of Retraction: Characterization Analysis of a High Speed, Low Resolution ADC Based on Simulation Results for Different Resolutions

2009 ◽  
Author(s):  
Baljit Singh ◽  
Parveen Kumar
Keyword(s):  
High Speed ◽  
Low Resolution ◽  
Simulation Results

scholarly journals Music Identification System Using MPEG-7 Audio Signature Descriptors

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Shingchern D. You ◽  
Wei-Hwa Chen ◽  
Woei-Kae Chen
Keyword(s):  
High Speed ◽  
High Accuracy ◽  
The Internet ◽  
Identification System ◽  
Decision Threshold ◽  
Low Resolution ◽  
Full Resolution ◽  
Music Identification ◽  
Simulation Results

This paper describes a multiresolution system based on MPEG-7 audio signature descriptors for music identification. Such an identification system may be used to detect illegally copied music circulated over the Internet. In the proposed system, low-resolution descriptors are used to search likely candidates, and then full-resolution descriptors are used to identify the unknown (query) audio. With this arrangement, the proposed system achieves both high speed and high accuracy. To deal with the problem that a piece of query audio may not be inside the system’s database, we suggest two different methods to find the decision threshold. Simulation results show that the proposed method II can achieve an accuracy of 99.4% for query inputs both inside and outside the database. Overall, it is highly possible to use the proposed system for copyright control.

scholarly journals Verification of electric steel punching simulation results using microhardness

2021 ◽  
Author(s):  
Sampsa Vili Antero Laakso ◽  
Ugur Aydin ◽  
Peter Krajnik
Keyword(s):  
Plastic Deformation ◽  
High Speed ◽  
Steel Sheet ◽  
Electrical Steel ◽  
High Speed Steel ◽  
Experimental Methods ◽  
Fem Simulations ◽  
Iron Losses ◽  
Simulation Results ◽  
Electrical Steel Sheet

AbstractOne of the most dominant manufacturing methods in the production of electromechanical devices from sheet metal is punching. In punching, the material undergoes plastic deformation and finally fracture. Punching of an electrical steel sheet causes plastic deformation on the edges of the part, which affects the magnetic properties of the material, i.e., increases iron losses in the material, which in turn has a negative effect on the performance of the electromagnetic devices in the final product. Therefore, punching-induced iron losses decrease the energy efficiency of the device. FEM simulations of punching have shown significantly increased plastic deformation on the workpiece edges with increasing tool wear. In order to identify the critical tool wear, after which the iron losses have increased beyond acceptable limits, the simulation results must be verified with experimental methods. The acceptable limits are pushed further in the standards by the International Electrotechnical Commission (IEC). The new standard (IEC TS 60034-30-2:2016) has much stricter limits regarding the energy efficiency of electromechanical machines, with an IE5 class efficiency that exceeds the previous IE4 class (IEC 60034-30-1:2014) requirements by 30%. The simulations are done using Scientific Forming Technologies Corporation Deform, a finite element software for material processing simulations. The electrical steel used is M400-50A, and the tool material is Vanadis 23, a powder-based high-speed steel. Vanadis 23 is a high alloyed powder metallurgical high-speed steel with a high abrasive wear resistance and a high compressive strength. It is suitable for cold work processing like punching. In the existing literature, FEM simulations and experimental methods have been incorporated for investigating the edge deformation properties of sheared surfaces, but there is a research gap in verifying the simulation results with the experimental methods. In this paper, FEM simulation of the punching process is verified using an electrical steel sheet from real production environment and measuring the deformation of the edges using microhardness measurements. The simulations show high plastic deformation 50 μm into the workpiece edge, a result that is shown to be in good agreement with the experimental results.

A Dicode Signaling Scheme for Capacitively Coupled Interface

2011 ◽  
Vol 497 ◽  
pp. 296-305
Author(s):  
Yasushi Yuminaka ◽  
Kyohei Kawano
Keyword(s):  
Partial Response ◽  
Data Transmission ◽  
High Speed ◽  
Circuit Simulation ◽  
Frequency Bandwidth ◽  
Capacitively Coupled ◽  
Limited Frequency ◽  
Simulation Results ◽  
Response Coding ◽  
The Impact

In this paper, we present a bandwidth-efficient partial-response signaling scheme for capacitivelycoupled chip-to-chip data transmission to increase data rate. Partial-response coding is knownas a technique that allows high-speed transmission while using a limited frequency bandwidth, by allowingcontrolled intersymbol interference (ISI). Analysis and circuit simulation results are presentedto show the impact of duobinary (1+D) and dicode (1-D) partial-response signaling for capacitivelycoupled interface.

Simulation on the Regulating Characteristics of the Pulse Modulation Hydraulic Hammer

2011 ◽  
Vol 422 ◽  
pp. 176-183
Author(s):  
Gang Wang ◽  
Yu Wan Cen
Keyword(s):  
Time Delay ◽  
Simulation Model ◽  
Impact Energy ◽  
High Speed ◽  
Impact Frequency ◽  
Pulse Modulation ◽  
Motion Equations ◽  
Hydraulic Hammer ◽  
Working Frequency ◽  
Simulation Results

To improve the regulating characteristics of impact energy, simplify structure of hydraulic hammer, a new pulse modulation hydraulic hammer is presented in the paper which can help regulate its impact frequency easily. The motion equations of the hydraulic hammer are established, its simulation model is obtained and the dynamic simulation is carried out on AMESim. The dynamics of high-speed ON/OFF valve is taken into account in the simulation model. The tendency of simulation results conforms to experimental results; it shows that the pulse modulation hydraulic hammer is feasible, and the hydraulic hammer model is reasonable. The time delay in high working frequency is also analyzed.

scholarly journals Broadband Power Line Communication for Integration of Energy Sensors within a Smart City Ecosystem

Sensors ◽  
2021 ◽  
Vol 21 (10) ◽  
pp. 3402
Author(s):  
Jan Slacik ◽  
Petr Mlynek ◽  
Martin Rusz ◽  
Petr Musil ◽  
Lukas Benesl ◽  
...  
Keyword(s):  
Smart Grids ◽  
High Speed ◽  
Power Line ◽  
Experimental Simulation ◽  
Power Line Communication ◽  
Experimental Measurements ◽  
Simulation Tool ◽  
Smart Metering ◽  
Complex Simulation ◽  
Simulation Results

The popularity of the Power Line Communication (PLC) system has decreased due to significant deficiencies in the technology itself, even though new wire installation is not required. In particular, regarding the request for high-speed throughput to fulfill smart-grid requirements, Broadband Power Line (BPLC) can be considered. This paper approaches PLC technology as an object of simulation experimentation in the Broadband Power Line Communication (BPLC) area. Several experimental measurements in a real environment are also given. This paper demonstrates these experimental simulation results as potential mechanisms for creating a complex simulation tool for various PLC technologies focusing on communication with end devices such as sensors and meters. The aim is to demonstrate the potential and limits of BPLC technology for implementation in Smart Grids or Smart Metering applications.

A LOW-POWER AND HIGH-SPEED D FLIP-FLOP USING A SINGLE LATCH

2002 ◽  
Vol 11 (01) ◽  
pp. 51-55
Author(s):  
ROBERT C. CHANG ◽  
L.-C. HSU ◽  
M.-C. SUN
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Power Dissipation ◽  
High Speed ◽  
Operating Frequency ◽  
Flip Flop ◽  
Lower Power ◽  
Simulation Results ◽  
Hspice Simulation

A novel low-power and high-speed D flip-flop is presented in this letter. The flip-flop consists of a single low-power latch, which is controlled by a positive narrow pulse. Hence, fewer transistors are used and lower power consumption is achieved. HSPICE simulation results show that power dissipation of the proposed D flip-flop has been reduced up to 76%. The operating frequency of the flip-flop is also greatly increased.

An improved model on forecasting temperature rise of high-speed angular contact ball bearings considering structural constraints

2018 ◽  
Vol 70 (1) ◽  
pp. 15-22 ◽  
Author(s):  
De-xing Zheng ◽  
Weifang Chen ◽  
Miaomiao Li
Keyword(s):  
Heat Generation ◽  
Temperature Rise ◽  
High Speed ◽  
Structural Constraints ◽  
Ball Bearings ◽  
Content Type ◽  
Grid Model ◽  
Simulation Results ◽  
Operation Parameters ◽  
Improved Model

Purpose Thermal performances are key factors impacting the operation of angular contact ball bearings. Heat generation and transfer about angular contact ball bearings, however, have not been addressed thoroughly. So far, most researchers only considered the convection effect between bearing housings and air, whereas the cooling/lubrication operation parameters and configuration effect were not taken into account when analyzing the thermal behaviors of bearings. This paper aims to analyze the structural constraints of high-speed spindle, structural features of bearing, heat conduction and convection to study the heat generation and transfer of high-speed angular contact ball bearings. Design/methodology/approach Based on the generalized Ohm’s law, the thermal grid model of angular contact ball bearing of high-speed spindle was first established. Next Gauss–Seidel method was used to solve the equations group by Matlab, and the nodes temperature was calculated. Finally, the bearing temperature rise was tested, and the comparative analysis was made with the simulation results. Findings The results indicate that the simulation results of bearing temperature rise for the proposed model are in better agreement with the test values. So, the thermal grid model established is verified. Originality/value This paper shows an improved model on forecasting temperature rise of high-speed angular contact ball bearings. In modeling, the cooling/lubrication operation parameters and structural constraints are integrated. As a result, the bearing temperature variation can be forecasted more accurately, which may be beneficial to improve bearing operating accuracy and bearing service life.

H∞Control for PMLSM Suspension Platform Based on PDFF

2011 ◽  
Vol 383-390 ◽  
pp. 6886-6892
Author(s):  
Jia Kuan Xia ◽  
Yi Na Wang ◽  
Yi Biao Sun
Keyword(s):  
Feedback Linearization ◽  
High Speed ◽  
Normal Force ◽  
Dynamic Stiffness ◽  
Linearization Method ◽  
Dynamic Decoupling ◽  
Fast Tracking ◽  
Speed Controller ◽  
Simulation Results ◽  
Proportional Controller

Permanent magnet linear synchronous motor (PMLSM) suspension system has the merits of no friction, high-speed, high response and so on, using the normal force achieve the mover suspension. The servo performance is affected by the nonlinear coupling between the horizontal trust and vertical normal force, parameters uncertainties and load disturbances. The feedback linearization method is used to achieve the dynamic decoupling of the PMLSM suspicion system and decoupling it Into two linear subsystems; to solve the conflict between disturbance restraint and fast tracking performance, increase the robustness and dynamic stiffness for system, H∞ speed controller based on PDFF and position proportional controller are designed. Simulation results show that the proposed control strategy guarantees the high speed and high precision positioning performance for horizontal axis; the good rigidity and stability for normal suspension length and the strong robustness against load disturbances and parameters variations for the two axes.

Transient Computational Fluid Dynamics/Discrete Element Method Simulation of Gas–Solid Flow in a Spouted Bed and Its Validation by High-Speed Imaging Experiment

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Ling Zhou ◽  
Lingjie Zhang ◽  
Weidong Shi ◽  
Ramesh Agarwal ◽  
Wei Li
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Discrete Element Method ◽  
Fluidized Bed ◽  
High Speed ◽  
Discrete Element ◽  
Bubble Shape ◽  
High Speed Imaging ◽  
Bed Height ◽  
Simulation Results

A coupled computational fluid dynamics (CFD)/discrete element method (DEM) is used to simulate the gas–solid two-phase flow in a laboratory-scale spouted fluidized bed. Transient experimental results in the spouted fluidized bed are obtained in a special test rig using the high-speed imaging technique. The computational domain of the quasi-three-dimensional (3D) spouted fluidized bed is simulated using the commercial CFD flow solver ANSYS-fluent. Hydrodynamic flow field is computed by solving the incompressible continuity and Navier–Stokes equations, while the motion of the solid particles is modeled by the Newtonian equations of motion. Thus, an Eulerian–Lagrangian approach is used to couple the hydrodynamics with the particle dynamics. The bed height, bubble shape, and static pressure are compared between the simulation and the experiment. At the initial stage of fluidization, the simulation results are in a very good agreement with the experimental results; the bed height and the bubble shape are almost identical. However, the bubble diameter and the height of the bed are slightly smaller than in the experimental measurements near the stage of bubble breakup. The simulation results with their experimental validation demonstrate that the CFD/DEM coupled method can be successfully used to simulate the transient gas–solid flow behavior in a fluidized bed which is not possible to simulate accurately using the granular approach of purely Euler simulation. This work should help in gaining deeper insight into the spouted fluidized bed behavior to determine best practices for further modeling and design of the industrial scale fluidized beds.

scholarly journals Randomized scheduling algorithm for virtual output queuing switch at the presence of non-uniform traffic

2019 ◽  
Vol 8 (1) ◽  
pp. 50
Author(s):  
Ali Ghiasian ◽  
Majid Jamali
Keyword(s):  
Randomized Algorithms ◽  
High Speed ◽  
Time Slot ◽  
Scheduling Algorithm ◽  
Superior Performance ◽  
High Complexity ◽  
Maximum Weight ◽  
Switch Architecture ◽  
Simulation Results ◽  
Maximum Weight Matching

<span>Virtual Output Queuing (VOQ) is a well-known queuing discipline in data switch architecture that eliminates Head Of Line (HOL) blocking issue. In VOQ scheme, for each output port, a separate FIFO is maintained by each input port. Consequently, a scheduling algorithm is required to determine the order of service to virtual queues at each time slot. Maximum Weight Matching (MWM) is a well-known scheduling algorithm that achieves the entire throughput region. Despite of outstanding attainable throughput, high complexity of MWM makes it an impractical algorithm for implementation in high-speed switches. To overcome this challenge, a number of randomized algorithms have been proposed in the literature. But they commonly perform poorly when input traffic does not uniformly select output ports. In this paper, we propose two randomized algorithms that outperform the well-known formerly proposed solutions. We exploit a method to keep a parametric number of heavy edges from the last time matching and mix it by randomly generated matching to produce a new schedule. Simulation results confirm the superior performance of the proposed algorithms.</span>

Sign in / Sign up

Export Citation Format

Share Document