Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor

1998 ◽  
Vol 120 (3) ◽  
pp. 477-486 ◽  
Author(s):  
D. W. Thompson ◽  
P. I. King ◽  
D. C. Rabe
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Percent Improvement ◽  
Flow Compressor

The effects of stepped-tip gaps and clearance levels on the performance of a transonic axial-flow compressor rotor were experimentally determined. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested for an optimum tip clearance with variations in stepped gaps machined into the casing near the aft tip region of the rotor. Nine causing geometries were investigated consisting of three step profiles at each of three clearance levels. For small and intermediate clearances, stepped tip gaps were found to improve pressure ratio, efficiency, and flow range for most operating conditions. At 100 percent design rotor speed, stepped tip gaps produced a doubling of mass flow range with as much as a 2.0 percent increase in mass flow and a 1.5 percent improvement in efficiency. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an optimum casing profile.

Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor

1997 ◽  
Author(s):  
Donald W. Thompson ◽  
Paul I. King ◽  
Douglas C. Rabe
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Compressor Performance ◽  
Flow Compressor

The effects of stepped tip gaps and clearance levels on the performance of a transonic axial-flow compressor rotor were experimentally determined. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested for an optimum tip clearance with variations in stepped gaps machined into the casing near the aft tip region of the rotor. Nine casing geometries were investigated consisting of three step profiles at each of three clearance levels. For small and intermediate clearances, stepped tip gaps were found to improve pressure ratio, efficiency, and flow range for most operating conditions. At 100% design rotor speed, stepped tip gaps produced a doubling of mass flow range with as much as a 2.0% increase in mass flow and a 1.5% improvement in efficiency. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an optimum casing profile.

Experimental and Computational Investigation of Stepped Tip Gap Effects on the Flowfield of a Transonic Axial-Flow Compressor Rotor

1998 ◽  
Author(s):  
Donald W. Thompson ◽  
Paul I. King ◽  
Chunill Hah ◽  
Douglas C. Rabe
Keyword(s):  
Fluid Dynamic ◽  
Pressure Ratio ◽  
Effective Means ◽  
Axial Flow ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Compressor Performance ◽  
Flow Compressor

The effects of stepped tip gaps and clearance levels on the flowfield of a transonic axial-flow compressor rotor were experimentally and computationally determined. This paper complements a previous experimental study by the authors regarding the effects of stepped tip gaps and clearance levels on the performance of an axial-flow compressor rotor. In the current study, the generation of blockage associated with the variation of geometry in the rotor tip region was examined. The shock-vortex interaction generating the blockage was characterized, and a theory and mechanism for relocation of blockage in the rotor tip region was developed. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested with stepped gaps machined into the casing near the aft tip region of the rotor. Nine casing geometries were investigated consisting of three step profiles at each of three clearance levels. Computational Fluid Dynamic modeling of tip geometry effects also was performed. Increased tip clearance was found to increase the amount of flow blockage near the rotor tip. Stepped tip gaps were found to be an effective means of reducing the effects of tip region blockage, resulting in improved pressure ratio, efficiency, and mass flow. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an improved casing profile.

scholarly journals Effect of Circumferential Single Casing Groove Location on the Flow Stability under Tip-Clearance Effect in a Transonic Axial Flow Compressor Rotor

Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6143
Author(s):  
Xiaoxiong Wu ◽  
Bo Liu ◽  
Botao Zhang ◽  
Xiaochen Mao
Keyword(s):  
Control Mechanism ◽  
Incidence Angle ◽  
Axial Flow ◽  
Flow Stability ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Flow Angle ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor

Numerical simulations have been performed to study the effect of the circumferential single-grooved casing treatment (CT) at multiple locations on the tip-flow stability and the corresponding control mechanism at three tip-clearance-size (TCS) schemes in a transonic axial flow compressor rotor. The results show that the CT is more efficient when its groove is located from 10% to 40% tip axial chord, and G2 (located at near 20% tip axial chord) is the best CT scheme in terms of stall-margin improvement for the three TCS schemes. For effective CTs, the tip-leakage-flow (TLF) intensity, entropy generation and tip-flow blockage are reduced, which makes the interface between TLF and mainstream move downstream. A quantitative analysis of the relative inlet flow angle indicates that the reduction of flow incidence angle is not necessary to improve the flow stability for this transonic rotor. The control mechanism may be different for different TCS schemes due to the distinction of the stall inception process. For a better application of CT, the blade tip profile should be further modified by using an optimization method to adjust the shock position and strength during the design of a more efficient CT.

Numerical Investigations of the Coupled Flow Through a Subsonic Compressor Rotor and Axial Skewed Slot

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yangfeng Zhang
Keyword(s):  
Axial Flow ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Through ◽  
Flow Compressor

In order to advance the understanding of the fundamental mechanisms of axial skewed slot casing treatment and their effects on the subsonic axial-flow compressor flow field, the coupled unsteady flow through a subsonic compressor rotor and the axial skewed slot was simulated with a state-of-the-art multiblock flow solver. The computational results were first compared with available measured data, that showed the numerical procedure calculates the overall effect of the axial skewed slot correctly. Then, the numerically obtained flow fields were interrogated to identify the physical mechanism responsible for improvement in stall margin of a modern subsonic axial-flow compressor rotor due to the discrete skewed slots. It was found that the axial skewed slot casing treatment can increase the stall margin of subsonic compressor by repositioning of the tip clearance flow trajectory further toward the trailing of the blade passage and retarding the movement of the incoming∕tip clearance flow interface toward the rotor leading edge plane.

Numerical Simulation of Steady Air Injection Flow Control Effects on a Transonic Axial Flow Compressor

2012 ◽  
Vol 224 ◽  
pp. 352-357
Author(s):  
Islem Benhegouga ◽  
Ce Yang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Leading Edge ◽  
Air Injection ◽  
Axial Flow Compressor ◽  
Blade Tip ◽  
Flow Compressor

In this work, steady air injection upstream of the blade leading edge was used in a transonic axial flow compressor, NASA rotor 37. The injectors were placed at 27 % upstream of the axial chord length at blade tip, the injection mass flow rate is 3% of the chock mass flow rate, and 3 yaw angles were used, respectively -20°, -30°, and -40°. Negative yaw angles were measured relative to the compressor face in opposite direction of rotational speeds. To reveal the mechanism, steady numerical simulations were performed using FINE/TURBO software package. The results show that the stall mass flow can be decreased about 2.5 %, and an increase in the total pressure ratio up to 0.5%.

1118 Effect of Tip Clearance on Rotating Stall Inception in an Axial Flow Compressor Rotor

2009 ◽  
Vol 2009 (0) ◽  
pp. 377-378 ◽  
Author(s):  
Hiroaki KIKUTA ◽  
Masato FURUKAWA ◽  
Satoshi GUNJISHIMA ◽  
Kenichiro IWAKIRI ◽  
Takuro KAMEDA
Keyword(s):  
Axial Flow ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Stall Inception ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor

2415 Effect of Tip Clearance on Structure of Rotating Stall Cell in an Axial Flow Compressor Rotor

2006 ◽  
Vol 2006.2 (0) ◽  
pp. 149-150
Author(s):  
Sho BONKOHARA ◽  
Ken-ichiro IWAKIRI ◽  
Ryusuke OHTAGURO ◽  
Yasuhiro SHIBAMOTO ◽  
Masato FURUKAWA
Keyword(s):  
Axial Flow ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor

Design and Test of a Transonic Axial Splittered Rotor

2015 ◽  
Author(s):  
Garth V. Hobson ◽  
Anthony J. Gannon ◽  
Scott Drayton
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Design Procedure ◽  
Tip Clearance ◽  
Turbine Engine ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Transonic Axial Compressor ◽  
Commercial Off The Shelf

A new design procedure was developed that uses commercial-off-the-shelf software (MATLAB, SolidWorks, and ANSYS-CFX) for the geometric rendering and analysis of a transonic axial compressor rotor with splitter blades. Predictive numerical simulations were conducted and experimental data were collected in a Transonic Compressor Rig. This study advanced the understanding of splitter blade geometry, placement, and performance benefits. In particular, it was determined that moving the splitter blade forward in the passage between the main blades, which was a departure from the trends demonstrated in the few available previous transonic axial compressor splitter blade studies, increased the mass flow range with no loss in overall performance. With a large 0.91 mm (0.036 in) tip clearance, to preserve the integrity of the rotor, the experimentally measured peak total-to-total pressure ratio was 1.69 and the peak total-to-total isentropic efficiency was 72 percent at 100 percent design speed. Additionally, a higher than predicted 7.5 percent mass flow rate range was experimentally measured, which would make for easier engine control if this concept were to be included in an actual gas turbine engine.

Experimental investigations on instability evolution in a transonic compressor at different rotor speeds

2015 ◽  
Vol 229 (18) ◽  
pp. 3378-3391 ◽  
Author(s):  
Qiushi Li ◽  
Tianyu Pan ◽  
Tailu Sun ◽  
Zhiping Li ◽  
Yifang Gong
Keyword(s):  
Low Frequency ◽  
Axial Flow ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Rotor Speed ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
New Type ◽  
Flow Compressor

Experimental investigations are conducted to study the instability evolution in a transonic axial flow compressor at four specific rotor speeds covering both subsonic and transonic operating conditions. Two routes of evolution to final instability are observed in the test compressor: at low rotor speeds, a disturbance in the rotor tip region occurs and then leads to rotating stall, while at high rotor speeds, a low-frequency disturbance in the hub region leads the compressor into instability. Different from stall and surge, this new type of compressor instability at high rotor speed is initiated through the development of a low-frequency axisymmetric disturbance at the hub, and we name it “partial surge”. The frequency of this low-frequency disturbance is approximately the Helmholtz frequency of the system and remains constant during instability inception. Finally, a possible mechanism for the occurrence of different instability evolutions and the formation of partial surge are also discussed.

Numerical Studies on Effect of Stepped Tip Clearance Height on the Performance of Single Stage Transonic Axial Flow Compressor

2013 ◽  
Author(s):  
Pritam Batabyal ◽  
Dilipkumar B. Alone ◽  
S. K. Maharana
Keyword(s):  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Flow ◽  
Single Stage ◽  
Tip Clearance ◽  
Baseline Model ◽  
Axial Flow Compressor ◽  
Design Speed ◽  
Flow Compressor

This paper presents a numerical case study of various stepped tip clearances and their effect on the performance of a single stage transonic axial flow compressor, using commercially available software ANSYS FLUENT 14.0. A steady state, implicit, three dimensional, pressure based flow solver with SST k-Ω turbulence model has been selected for the numerical study. The stepped tip clearances have been compared with the baseline model of zero tip clearance at 70% and 100 % design speed. It has been observed that the compressor peak stage efficiency and maximum stage pressure ratio decreases as the tip clearances in the rear part are increased. The stall margin also increases with increase in tip clearance compared to the baseline model. An ‘optimum’ value of stepped tip clearance has been obtained giving peak stage compressor performance. The CFD results have been validated with the earlier published experimental data on the same compressor at 70% design speed.

Sign in / Sign up

Export Citation Format

Share Document