The Influence of a Laminar Boundary Layer and Laminar Injection on Film Cooling Performance

1982 ◽  
Vol 104 (2) ◽  
pp. 355-362 ◽  
Author(s):  
R. J. Goldstein ◽  
T. Yoshida
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Laminar Boundary Layer ◽  
Film Cooling ◽  
Transport Mechanisms ◽  
Flow Measurements ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Injection Flow

Measurements are reported of the film cooling effectiveness and heat transfer following injection of air into a mainstream of air. A single row of circular injection holes inclined at an angle of 35 deg is used with a lateral spacing between the holes of 3 dia. Low Reynolds number mainstream and injection flow permit studying the influence of a laminar approaching boundary layer and laminar film coolant flow. Measurements of the surface heat transfer taken with no injection indicate that the hole openings can effectively trip the laminar boundary layer into a turbulent flow. The type of the approaching boundary layer has relatively little influence on either the adiabatic effectiveness or the heat transfer with film cooling. The importance of the nature of the injected flow on film cooling performance can at least be qualitatively explained by the differences in the transport mechanisms and in the penetration of the injected air into the mainstream.

Endwall Heat Transfer and Cooling Performance of a Transonic Turbine Vane with Upstream Injection Flow

2021 ◽  
pp. 1-24
Author(s):  
Zhigang LI ◽  
Bo Bai ◽  
Jun Li ◽  
Shuo Mao ◽  
Wing Ng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Density Ratio ◽  
Gas Temperature ◽  
Blow Down ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Injection Flow ◽  
Coolant Injection ◽  
Exit Mach Number

Abstract Detailed experimental and numerical studies on endwall heat transfer and cooling performance with coolant injection flow through upstream discrete holes is presented in this paper. High resolution heat transfer coefficient (HTC) and adiabatic film cooling effectiveness values were measured using a transient infrared thermography technique on an axisymmetric contoured endwall. The tests were performed in a transonic linear cascade blow-down wind tunnel facility. Conditions were representative of a land-based power generation turbine with exit Mach number of 0.85 corresponding to exit Reynolds number of 1.5 × 106, based on exit condition and axial chord length. A high turbulence level of 16% with an integral length scale of 3.6%P was generated using inlet turbulence grid to reproduce the typical turbulence conditions in real turbine. Low temperature air was used to simulate the typical coolant-to-mainstream condition by controlling two parameters of the upstream coolant injection flow: mass flow rate to determine the coolant-to-mainstream blowing ratio (BR = 2.5, 3.5), and gas temperature to determine the density ratio (DR = 1.2). To highlight the interactions between the upstream coolant flow and the passage secondary flow combined with the influence on the endwall heat transfer and cooling performance, a comparison of CFD predictions to experimental results was performed by solving steady-state Reynolds-Averaged Navier-Stokes (RANS) using the commercial CFD solver ANSYS Fluent V.15.

Investigations on the Influence of Rib Orientation Angle on Film Cooling Performance of Compound Holes

2018 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hai-yong Liu ◽  
Hui-ren Zhu ◽  
Jian-xia Luo
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Orientation Angle ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

To investigate the effects of the inclined ribs on internal flow structure in film hole and the film cooling performance on outer surface, experimental and numerical studies are conducted on the effects of rib orientation angle on film cooling of compound cylindrical holes. Three coolant channel cases, including two ribbed cross-flow channels (135° and 45° angled ribs) and the plenum case, are studied under three blowing ratios (0.5, 1.0 and 2.0). 2D contours of film cooling effectiveness as well as heat transfer coefficient were measured by transient liquid crystal measurement technique (TLC). The steady RANS simulations with realizable k-ε turbulence model and enhanced wall treatment were performed. The results show that the spanwise width of film coverage is greatly influenced by the rib orientation angle. The spanwise width of the 45° rib case is obviously larger than that of the 135° rib case under lower blowing ratios. When the blowing ratio is 1.0, the area-averaged cooling effectiveness of the 135° rib case and the 45° rib case are higher than that of the plenum case by 38% and 107%, respectively. With the increase of blowing ratio, the film coverage difference between different rib orientation cases becomes smaller. The 45° rib case also produces higher heat transfer coefficient, which is higher than the 135° rib case by 3.4–8.7% within the studied blowing ratio range. Furthermore, the discharge coefficient of the 45° rib case is the lowest among the three cases. The helical motion of coolant flow is observed in the hole of 45° rib case. The jet divides into two parts after being blown out of the hole due to this motion, which induces strong velocity separation and loss. For the 135° rib case, the vortex in the upper half region of the secondary-flow channel rotates in the same direction with the hole inclination direction, which leads to the straight streamlines and thus results in lower loss and higher discharge coefficient.

Film Cooling From a Row of Holes With Both Ends Embedded in Transverse Slots

2008 ◽  
Author(s):  
D. H. Zhang ◽  
L. Sun ◽  
Q. Y. Chen ◽  
M. Lin ◽  
M. Zeng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Aerodynamic Performance ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Discharge Coefficients ◽  
Cylindrical Holes

Embedding a row of typical cylindrical holes in a transverse slot can improve the cooling performance. Rectangular slots can increase the cooling effectiveness but is at the cost of decreasing of discharge coefficients. An experiment is conducted to examine the effects of an overlying transverse inclined trench on the film cooling performance of axial holes. Four different trench configurations are tested including the baseline inclined cylindrical holes. The influence of the geometry of the upstream lip of the exit trench and the geometry of the inlet trench on cooling performance is examined. Detailed film cooling effectiveness and heat transfer coefficients are obtained separately using the steady state IR thermography technique. The discharge coefficients are also acquired to evaluate the aerodynamic performance of different hole configurations. The results show that the film cooling holes with both ends embedded in slots can provide higher film cooling effectiveness and lower heat transfer coefficients; it also can provide higher discharge coefficients whilst retaining the mechanical strength of a row of discrete holes. The cooling performance and the aerodynamic performance of the holes with both ends embedded in inclined slots are superior to the holes with only exit trenched. To a certain extent, the configuration of the upstream lip of the exit trench affects the cooling performance of the downstream of the trench. The filleting for the film hole inlet avail the improvement of the cooling effect, but not for the film hole outlet. Comparing film cooling with embedded holes to unembedded holes, the overall heat flux ratio shows that the film holes with both ends embedded in slots and filleting for the film hole inlet can produce the highest heat flux reduction.

Measurements in Film Cooling Flows With Periodic Wakes

2007 ◽  
Author(s):  
Kristofer M. Womack ◽  
Ralph J. Volino ◽  
Michael P. Schultz
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Constant Current ◽  
Percentage Increase ◽  
Flow Measurements ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flows ◽  
Cold Wire ◽  
Wake Passing

Film cooling flows subject to periodic wakes were studied experimentally. The wakes were generated with a spoked wheel upstream of a flat plate. Cases with a single row of cylindrical film cooling holes inclined at 35 degrees to the surface were considered at blowing ratios of 0.25, 0.50, and 1.0 with a steady freestream and with wake Strouhal numbers of 0.15, 0.30, and 0.60. Temperature measurements were made using an infrared camera, thermocouples, and constant current (cold wire) anemometry. Hot wire anemometry was used for velocity measurements. The local film cooling effectiveness and heat transfer coefficient were determined from the measured temperatures. Phase locked flow temperature fields were determined from cold wire surveys. Wakes decreased the film cooling effectiveness for blowing ratios of 0.25 and 0.50 when compared to steady freestream cases. In contrast, effectiveness increased with Strouhal number for the 1.0 blowing ratio cases, as the wakes helped mitigate the effects of jet liftoff. Heat transfer coefficients increased with wake passing frequency, with nearly the same percentage increase in cases with and without film cooling. The time resolved flow measurements show the interaction of the wakes with the film cooling jets. Near-wall flow measurements are used to infer the instantaneous film cooling effectiveness as it changes during the wake passing cycle.

Investigations on the Influence of Rib Orientation Angle on Film Cooling Performance of Cylindrical Holes

2017 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hui-ren Zhu ◽  
Jian-xia Luo ◽  
Ying-ni Zhai
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Cross Flow ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Flow Channels ◽  
Cylindrical Holes

This paper presents an experimental and numerical investigation on the film cooling with different coolant feeding channel structures. Two ribbed cross-flow channels with rib-orientation of 135° and 45° respectively and the plenum coolant channel have been studied and compared to find out the effect of rib orientation on the film cooling performances of cylindrical holes. The film cooling effectiveness and heat transfer coefficient were measured by the transient heat transfer measurement technique with narrow-band thermochromic liquid crystal. Numerical simulations with realizable k-ε turbulence model were also performed to analyze the flow mechanism. The results show that the coolant channel structure has a notable effect on the flow structure of film jet which is the most significant mechanism affecting the film cooling performance. Generally, film cooling cases fed with ribbed cross-flow channels have asymmetric counter-rotating vortex structures and related asymmetric temperature distributions, which make the film cooling effectiveness and the heat transfer coefficient distributions asymmetric to the hole centerline. The discharge coefficient of the 45° rib case is the lowest among the three cases under all the blowing ratios. And the plenum case has higher discharge coefficient than the 135° rib case under low blowing ratio. With the increase of blowing ratio, the discharge coefficient of the 135° rib case gets larger than the plenum case gradually, because the vortex in the upper half region of the coolant channel rotates in the same direction with the film hole inclination direction and makes the jet easy to flow into the film hole in the 135° rib case.

Numerical Study on the Effects of V-Shaped Rib Angle on Film Cooling Performance for Turbine Blade Trailing Edge

2018 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hai-yong Liu ◽  
Qi-jiao He ◽  
Gang Xie
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Turbine Blade ◽  
Film Cooling ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

The trailing edge of the high-pressure turbine blade presents significant challenges to cooling structure design. To achieve better cooling performance at turbine blade trailing edge, a novel ribbed cutback structure is proposed for trailing edge cooling, which has rib structures on the cutback surface for heat transfer enhancement. In this study, numerical simulations have been performed on the effects of V-shaped rib angle on the film cooling characteristics and flow physics. Three V-shaped rib angles of 30°, 45° and 60° are studied. The distributions of adiabatic cooling effectiveness and heat transfer coefficient are obtained under blowing ratios with the value of 0.5, 1.0 and 1.5 respectively. Due to the relatively small rib height, the effect of V-shaped ribs on the film cooling effectiveness is not notable. The disadvantage of V-shaped ribs mainly exhibits at the downstream area of cutback surface. With the increase of V-shaped rib angle, the film cooling effectiveness becomes lower, but the values are still above 0.9. The V-shaped ribs obviously enhance the heat transfer on trailing edge cutback surface. The area-averaged heat transfer coefficient of the V-rib case is higher than that of the smooth case by 26.3–41.2%. The 45° V-rib case has higher heat transfer intensity than the other two V-shaped rib cases under all the three blowing ratios. However, the heat transfer coefficient distribution of the 60° V-rib case is more uniform. The heat transfer intensity of the 30° V-rib case is higher in the downstream region than the other two cases, but lower in the upstream region in which the difference becomes smaller with the increase of blowing ratio. The 45° V-rib case and the 60° V-rib case both reach the maximum value of area-averaged heat transfer intensity under blowing ratio is 1.0. Under higher blowing ratio, the 30° V-rib case and the 45° V-rib case outperform 2.1% and 6.7% higher value relative to the 60° V-rib case respectively due to the smaller velocity gradient in the 60° V-rib case in the downstream.

Conjugate Heat Transfer Predictions of Effusion Cooling: The Influence of Injection Hole Size on Cooling Performance

2012 ◽  
Author(s):  
H. I. Oguntade ◽  
G. E. Andrews ◽  
A. D. Burns ◽  
D. B. Ingham ◽  
M. Pourkashanian
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Hole Size ◽  
Internal Wall ◽  
Cooling Effectiveness ◽  
Large Hole ◽  
Flow Rates ◽  
Cooling Performance ◽  
Film Cooling Effectiveness

Conjugate heat transfer CFD was undertaken on the influence of hole size on effusion cooling. The coupled thermal mixing between the hot-gas and coolant jets and the heat transfer within the effusion walls were modelled using the ANSYS FLUENT software. The heat and mass transfer analogy was employed to predict the adiabatic film cooling effectiveness separately from the overall cooling effectiveness by adding a tracer gas to the coolant air and predicting its concentration at the inner wall surface. The geometries predicted were those investigated experimentally by Andrews and his co-workers using a 152mm length of effusion cooling with 10 rows of square array holes in a flat metal wall. Effusion of X/D of 4.6 and 1.85 were investigated at constant X, the large hole diameter at the lower X/D drastically reduces the hole blowing rate and this improves the film cooling and deteriorates the internal wall cooling. The CFD predictions enable these qualitative effects to be investigated in more detail. The agreement of predictions and experiment was very good at low coolant mass flow rates, but under-predicted the measurements at higher flow rates by about 5–12%. The experimental results showed that the smaller X/D gave a better overall cooling performance and the predictions also showed this, but demonstrated that it was not just to due improved effusion film cooling as there was not the expected large reduction in internal wall cooling.

Film Cooling Effectiveness and Mass/Heat Transfer Coefficient Downstream of One Row of Discrete Holes

1999 ◽  
Vol 121 (2) ◽  
pp. 225-232 ◽  
Author(s):  
R. J. Goldstein ◽  
P. Jin ◽  
R. L. Olson
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Density Ratio ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness

A special naphthalene sublimation technique is used to study the film cooling performance downstream of one row of holes of 35 deg inclination angle with 3d hole spacing and relatively small hole length to diameter ratio (L/d = 6.3). Both film cooling effectiveness and mass/heat transfer coefficient are determined for blowing rates from 0.5 to 2.0 with density ratio of 1.0. The mass transfer coefficient is measured using pure air film injection, while the film cooling effectiveness is derived from comparison of mass transfer coefficients obtained following injection of naphthalene-vapor-saturated air with those from pure air injection. This technique enables one to obtain detailed local information on film cooling performance. The laterally averaged and local film cooling effectiveness agree with previous experiments. The difference between mass/heat transfer coefficients and previous heat transfer results indicates that conduction error may play an important role in the earlier heat transfer measurements.

Numerical Evaluation of Influence of Internal Ribs on Heat Transfer in Flat Plate Film Cooling

2013 ◽  
Author(s):  
Yukiko Agata ◽  
Toshihiko Takahashi ◽  
Eiji Sakai ◽  
Koichi Nishino
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Turbine Inlet

To augment the thermal efficiency of combined power generation plants, the turbine inlet temperature of an industrial gas turbine has been increased. Cooling technology plays a vital role in the durability of gas turbine blades in situations in which the turbine inlet temperature exceeds the allowable temperature of the blade material. Cooling air is also directly associated with the reduction in thermal efficiency because bleed air from the compressor is used for turbine cooling. Thus, improvement in cooling performance has a marked impact on the further augmentation of thermal efficiency by increasing turbine inlet temperature. To evaluate film cooling performance on the basis of heat flux reduction, it is necessary to accurately estimate both heat transfer coefficient and adiabatic film cooling effectiveness. Most studies of film cooling, however, have focused on improving adiabatic film cooling effectiveness. In contrast, there are few studies focusing on heat transfer coefficient. One of the reasons for this is that adiabatic film cooling effectiveness is a performance parameter unique to film cooling. To preliminarily estimate the heat flux through a blade, heat transfer coefficient without film cooling can still be used as substitute. Moreover, the accurate CFD prediction of heat transfer coefficient with film cooling is difficult, compared with the evaluation of adiabatic film cooling effectiveness. Therefore, in this study, we addressed the CFD prediction of heat transfer coefficient with film cooling on a flat plate, and discussed its feasibility. Recent gas turbine blades operated at a turbine inlet temperature of over 1300 degree Celsius employ internal convection cooling with ribbed passages and external film cooling. These cooling technologies have been studied extensively, particularly regarding their individual effects. On the other hand, there are few investigations on the interaction between internal convection cooling and the film cooling. Although most of such film-cooling studies employed stagnant plenums to bleed cooling air, some researchers including the present authors have shown the marked impact of the conditions for supplying coolant air on film cooling performance. In this study, we focus particularly on the influence of internal rib orientation on external film cooling performance along the blade outer surface. CFD analysis is used to resolve the flow fields of the flat plate film cooling and to clarify the influence of rib orientation on heat-transfer.

scholarly journals Film Cooling From a Row of Holes Supplemented With Anti Vortex Holes

2007 ◽  
Author(s):  
Alok Dhungel ◽  
Yiping Lu ◽  
Wynn Phillips ◽  
Srinath V. Ekkad ◽  
James Heidmann
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Circular Cross Section ◽  
Flux Ratio ◽  
Upstream Region ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Cylindrical Holes ◽  
Film Cooling Holes

The primary focus of this paper is to study the film cooling performance for a row of cylindrical holes each supplemented with two symmetrical anti vortex holes which branch out from the main holes. The anti-vortex design was originally developed at NASA-Glenn Research Center by Dr. James Heidmann, co-author of this paper. This “anti-vortex” design is unique in that it requires only easily machinable round holes, unlike shaped film cooling holes and other advanced concepts. The hole design is intended to counteract the detrimental vorticity associated with standard circular cross-section film cooling holes. The geometry and orientation of the anti vortex holes greatly affect the cooling performance downstream, which is thoroughly investigated. By performing experiments at a single mainstream Reynolds number of 9683 based on the free stream velocity and film hole diameter at four different coolant-to-mainstream blowing ratio of 0.5, 1, 1.5, 2 and using the transient IR thermography technique, detailed film cooling effectiveness and heat transfer coefficients are obtained simultaneously from a single test. When the anti vortex holes are nearer to the primary film cooling holes and are developing from the base of the primary holes, better film cooling is accomplished as compared to other anti vortex hole orientations. When the anti vortex holes are laid back in the upstream region, film cooling diminishes considerably. Although an enhancement in heat transfer coefficient is seen in cases with high film cooling effectiveness, the overall heat flux ratio as compared to standard cylindrical holes is much lower. Thus cases with anti vortex holes placed near the main holes certainly show promising results.

Sign in / Sign up

Export Citation Format

Share Document