Analysis of Tool Wear—Part I: Theoretical Models of Flank Wear

1969 ◽  
Vol 91 (3) ◽  
pp. 790-796 ◽  
Author(s):  
A. Bhattacharyya ◽  
I. Ham
Keyword(s):  
Tool Wear ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Tools ◽  
Tool Material ◽  
High Strength ◽  
Theoretical Models ◽  
Flank Surface ◽  
Form Stability ◽  
Sufficient Strength

Cutting tools of sufficient strength against failure by brittle fracture or loss of “form stability” through rise of interface temperatures, still continue to fail by a process of “wear,” which is loss of cutting tool material through gradual interaction between the work and the tool material. Such wear can take place either at the principal flank surface or at the top face of the cutting tool for roughing and semiroughing cuts. Wear may also occur at the auxiliary flank surface resulting in grooving wear during fine machining or machining of high strength materials. The causes for such wear processes include (i) mechanical interaction (abrasion or adhesion and transfer type), (ii) thermochemical interaction (diffusion or chemical reaction). As a part of this investigation on tool wear, two theoretical models have been proposed for explaining mechanical wear at the flank surface. These models explain the nature and characteristics of wear growth and the sensitiveness and dependence of interaction phenomena between the tool-work pair.

Development and Application of Cermet Cutting Tools Material

2008 ◽  
Vol 375-376 ◽  
pp. 163-167 ◽  
Author(s):  
Tie Fu ◽  
Qi Xun Yu ◽  
Bin Liu ◽  
Yu Guang Wu
Keyword(s):  
Wear Resistance ◽  
Tool Wear ◽  
Cutting Force ◽  
High Strength Steel ◽  
Cutting Tool ◽  
Impact Resistance ◽  
Cutting Tools ◽  
Tool Material ◽  
High Strength ◽  
Carbide Insert

In this paper, the development and mechanical, physical properties on cermet cutting tool material are described. By using the cermet insert NT7 developed in recent years and WC based carbide insert YT14, the tool wear, impact and cutting force tests to high strength steel 38CrNi3MoVA (hardened and tempered, HRC36~40) are processed respectively. The results of these tests demonstrate that NT7 cutting tools have better performance on some characteristics, such as wear resistance, tool life and cutting force. And its ability of impact resistance is similar to YT14. These researches will benefit to the poplarizaion and application of cermet cutting tool.

Cutting Tool Wear and Mechanisms of Chip Formation During High-Speed Machining of Compacted Graphite Iron

2007 ◽  
Author(s):  
Niniza S. P. Dlamini ◽  
Iakovos Sigalas ◽  
Andreas Koursaris
Keyword(s):  
Tool Wear ◽  
Surface Finish ◽  
Failure Criterion ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Tools ◽  
Compacted Graphite Iron ◽  
Crater Wear ◽  
Compacted Graphite ◽  
Cutting Speeds

Cutting tool wear of polycrystalline cubic boron nitride (PcBN) tools was investigated in oblique turning experiments when machining compacted graphite iron at high cutting speeds, with the intention of elucidating the failure mechanisms of the cutting tools and presenting an analysis of the chip formation process. Dry finish turning experiments were conducted in a CNC lathe at cutting speeds in the range of 500–800m/min, at a feed rate of 0.05mm/rev and depth of cut of 0.2mm. Two different tool end-of-life criteria were used: a maximum flank wear scar size of 0.3mm (flank wear failure criterion) or loss of cutting edge due to rapid crater wear to a point where the cutting tool cannot machine with an acceptable surface finish (surface finish criterion). At high cutting speeds, the cutting tools failed prior to reaching the flank wear failure criterion due to rapid crater wear on the rake face of the cutting tools. Chip analysis, using SEM, revealed shear localized chips, with adiabatic shear bands produced in the primary and secondary shear zones.

Performance evaluation of a tungsten carbide–based self-lubricant cutting tool

2016 ◽  
Vol 232 (10) ◽  
pp. 1825-1836 ◽  
Author(s):  
Ayyankalai Muthuraja ◽  
Selvaraj Senthilvelan
Keyword(s):  
Tungsten Carbide ◽  
Cutting Force ◽  
Tool Life ◽  
Solid Lubricant ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Tools ◽  
Chip Morphology ◽  
Machined Surface ◽  
Flank Surface

Tungsten carbide cutting tools with and without solid lubricant (WC-10Co-5CaF2 and WC-10Co) were developed in-house via powder metallurgy. The developed cutting tools and a commercial WC-10Co cutting tool were used to machine cylindrical AISI 1020 steel material under dry conditions. The cutting force and average cutting tool temperature were continuously measured. The cutting tool flank surface and chip morphology after specific tool life (5 min of cutting) were examined to understand tool wear. The flank wear of the considered cutting tools was also measured to quantify the cutting tool life. The surface roughness of the workpiece was measured to determine the machining quality. The developed cutting tool with solid lubricant (WC-10Co-5CaF2) generated 20%–40% less cutting force compared to that of the developed cutting tool without solid lubricant (WC-10Co). In addition, the finish of the workpiece surface improved by 16%–20% when it was machined by the solid lubricant cutting tool. The cutting tool with solid lubricant (WC-10Co-5CaF2) exhibited a 15%–18% reduction in flank wear. Curlier and smaller saw tooth chips were generated from the WC-10Co-5CaF2 cutting tool, confirming that less heat was generated during the cutting process, and the finish of the machined surface was also improved.

Effect of residual elements on the machinability of leaded free machining steels

1980 ◽  
Vol 295 (1413) ◽  
pp. 87-88 ◽  
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Tool Life ◽  
High Speed ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Tool Material ◽  
High Speed Steel ◽  
Low Carbon ◽  
Wear Rates

The machinability of a material can be defined in terms of the wear rate of the cutting tool used to machine the material. The lower the tool wear rate or the greater the tool life the better the machinability. The wear processes of cutting tools are complicated, but recent work has shown that cutting tool wear rates during machining can be directly related to tool material wear rates when rubbing in a modified crossed cylinder wear experiment (Mills & Akhtar 1975). The wear of cutting tools can be simulated by simple experiments. Here I present results on the effect of total residual levels in leaded low carbon free machining steels on the tool life of M2 high speed steel. The results will be discussed in terms of a simple wear model.

scholarly journals Performance Comparison of Al2O3 Cutting Tool with and without Reinforcement of Graphene Nanoplatelets

2021 ◽  
Vol 10 (3) ◽  
pp. 93-96
Author(s):  
A.Gopala Krishna ◽  
R Peddi Raju
Keyword(s):  
Fracture Toughness ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Tools ◽  
Tool Material ◽  
Performance Comparison ◽  
Graphene Nanoplatelets ◽  
Cnc Machining ◽  
Machining Performance ◽  
Composite Tool

Al2O3 is a commonly used cutting tool material for machining cast iron and hard steels. However its low fracture toughness has been its potential drawback to use it for wider applications. In order to improve the fracture toughness, graphene nanoplatelets has been used as the reinforcement. The Al2O3 -TiCN composite have been made by powder metallurgy. The present work compares the performance characteristics of Al2O3 -TiCN with and without graphene nanoplatelets (GNP) in CNC machining. The machining performance of the prepared cutting tools is tested in terms of temperature generated, flank wear, cutting force and surface finish. It is observed that the prepared composite tool with GNP has much improved machining performance over the Al2O3 cutting tool that has no GNP reinforcement. The work has the unique novelty of using GNP as the reinforcement in Al2O3 cutting tool material

scholarly journals Integrating object detection and image segmentation for detecting the tool wear area on stitched image

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Wan-Ju Lin ◽  
Jian-Wen Chen ◽  
Jian-Ping Jhuang ◽  
Meng-Shiun Tsai ◽  
Che-Lun Hung ◽  
...  
Keyword(s):  
Tool Wear ◽  
Template Matching ◽  
Cutting Tool ◽  
Flank Wear ◽  
End Milling ◽  
Cutting Tools ◽  
Milling Process ◽  
Wear Area ◽  
Learning Techniques ◽  
The Times

AbstractFlank wear is the most common wear that happens in the end milling process. However, the process of detecting the flank wear is cumbersome. To achieve comprehensively automatic detecting the flank wear area of the spiral end milling cutter, this study proposed a novel flank wear detection method of combining the template matching and deep learning techniques to expand the curved surface images into panorama images, which is more available to detect the flank wear areas without choosing a specific position of cutting tool image. You Only Look Once v4 model was employed to automatically detect the range of cutting tips. Then, popular segmentation models, namely, U-Net, Segnet and Autoencoder were used to extract the areas of the tool flank wear. To evaluate the segmenting performance among these models, U-Net model obtained the best maximum dice coefficient score with 0.93. Moreover, the predicting wear areas of the U-Net model is presented in the trend figure, which can determine the times of the tool change depend on the curve of the tool wear. Overall, the experiments have shown that the proposed methods can effectively extract the tool wear regions of the spiral cutting tool. With the developed system, users can obtain detailed information about the cutting tool before being worn severely to change the cutting tools in advance.

Forecasting Performance of Ceramic Cutting Tool

2017 ◽  
Vol 736 ◽  
pp. 86-90 ◽  
Author(s):  
Vyacheslav Maksarov ◽  
A. Khalimonenko
Keyword(s):  
Electrical Resistance ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Tool Material ◽  
Ceramic Materials ◽  
Specific Electrical Resistance ◽  
Testing Methods ◽  
Microstructural Parameters ◽  
Forecasting Performance ◽  
Nondestructive Testing Methods

The article considers the problems of forecasting the performance of cutting tools equipped with replaceable ceramic cutting bits. It is proposed to forecast the operability of ceramic tools on the ground of dependence between its performance characteristics and the microstructural parameters of the tool material. It is proposed to determine the parameters of ceramic bits microstructure by a nondestructive testing methods based on measuring the specific electrical resistance of ceramic materials. As a result of the study we have undertaken, a relationship was detected between the performance and specific electrical resistance of ceramic cutting tools.

scholarly journals Milling Inconel 718 Workpiece With Cryogenically Treated And Untreated Cutting Tools

2021 ◽  
Author(s):  
Hüseyin Gürbüz ◽  
Şehmus Baday
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Abrasive Wear ◽  
Inconel 718 ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Tool Wear ◽  
Feed Force

Abstract Although Inconel 718 is an important material for modern aircraft and aerospace, it is a kind material, which is known to have low machinability. Especially, while these types of materials are machined, high cutting temperatures, BUE on cutting tool, high cutting forces and work hardening occur. Therefore, in recent years, instead of producing new cutting tools that can withstand these difficult conditions, cryogenic process, which is a heat treatment method to increase the wear resistance and hardness of the cutting tool, has been applied. In this experimental study, feed force, surface roughness, vibration, cutting tool wear, hardness and abrasive wear values that occurred as a result of milling of Inconel 718 material by means of cryogenically treated and untreated cutting tools were investigated. Three different cutting speeds (35-45-55 m/min) and three different feed rates (0.02-0.03-0.04 mm/tooth) at constant depth of cut (0.2 mm) were used as cutting parameters in the experiments. As a result of the experiments, lower feed forces, surface roughness, vibration and cutting tool wear were obtained with cryogenically treated cutting tools. As the feed rate and cutting speed were increased, it was seen that surface roughness, vibration and feed force values increased. At the end of the experiments, it was established that there was a significant relation between vibration and surface roughness. However, there appeared an inverse proportion between abrasive wear and hardness values. While BUE did not occur during cryogenically treated cutting tools, it was observed that BUE occurred in cutting tools which were not cryogenically treated.

scholarly journals Experimental Study on Tool Wear and Delamination in Milling CFRPs with TiAlN- and TiN-Coated Tools

Coatings ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 623 ◽  
Author(s):  
Dervis Ozkan ◽  
Peter Panjan ◽  
Mustafa Sabri Gok ◽  
Abdullah Cahit Karaoglanli
Keyword(s):  
Tool Wear ◽  
Cutting Tool ◽  
Failure Mechanisms ◽  
Cutting Tools ◽  
Machining Process ◽  
Dynamic Loads ◽  
Fiber Reinforced Polymers ◽  
Machining Parameters ◽  
Coated Tool ◽  
Cfrp Composite

Carbon fiber-reinforced polymers (CFRPs) have very good mechanical properties, such as extremely high tensile strength/weight ratios, tensile modulus/weight ratios, and high strengths. CFRP composites need to be machined with a suitable cutting tool; otherwise, the machining quality may be reduced, and failures often occur. However, as a result of the high hardness and low thermal conductivity of CFRPs, the cutting tools used in the milling process of these materials complete their lifetime in a short cycle, due to especially abrasive wear and related failure mechanisms. As a result of tool wear, some problems, such as delamination, fiber breakage, uncut fiber and thermal damage, emerge in CFRP composite under working conditions. As one of the main failure mechanisms emerging in the milling of CFRPs, delamination is primarily affected by the cutting tool material and geometry, machining parameters, and the dynamic loads arising during the machining process. Dynamic loads can lead to the breakage and/or wear of cutting tools in the milling of difficult-to-machine CFRPs. The present research was carried out to understand the influence of different machining parameters on tool abrasion, and the work piece damage mechanisms during CFRP milling are experimentally investigated. For this purpose, cutting tests were carried out using a (Physical Vapor Deposition) PVD-coated single layer TiAlN and TiN carbide tool, and the abrasion behavior of the coated tool was investigated under dry machining. To understand the wear process, scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS) was used. As a result of the experiments, it was determined that the hard and abrasive structure of the carbon fibers caused flank wear on TiAlN- and TiN-coated cutting tools. The best machining parameters in terms of the delamination damage of the CFRP composite were obtained at high cutting speeds and low feed rates. It was found that the higher wear values were observed at the TiAlN-coated tool, at the feed rate of 0.05 mm/tooth.

Research on Wear Property of Tool Flank by Dry Cutting of Austempering Ductile Iron

2011 ◽  
Vol 188 ◽  
pp. 38-42
Author(s):  
Dong Dong Wan ◽  
Xu Hong Guo ◽  
Chi Hong Wang
Keyword(s):  
Cutting Tool ◽  
Flank Wear ◽  
Cubic Boron Nitride ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
Wear Property ◽  
Dry Cutting ◽  
Quenching Temperature ◽  
Tool Flank Wear ◽  
Heat Treated

Three different cutting tools (ceramics CC6050, cubic boron nitride CB7025, carbide GC2025) were used for dry cutting of 3 groups of ADI which were heat-treated separately under different quenching temperatures. With the unified cutting parameters, the wear of tool flank of each cutter was studied and the main influencing factors of the wear were analyzed. Results showed that when the cutting parameters ap =0.2mm, f =0.16mm/r, vc =108m/min and the cutting tool was determined, the higher the quenching temperature was the lower the hardness of the test bars were and the tool flank wear was less; When the quenching temperature was determined, the more the produced BUE (build up edge) of the cutting tool was the less the tool flank wear was.

Sign in / Sign up

Export Citation Format

Share Document