Autoignition Limits of Hydrogen at Relevant Reheat Combustor Operating Conditions

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
J. Fleck ◽  
P. Griebel ◽  
A.M. Steinberg ◽  
M. Stöhr ◽  
M. Aigner ◽  
...  
Keyword(s):  
Flue Gas ◽  
Gas Turbines ◽  
High Speed ◽  
Initial Position ◽  
Operating Conditions ◽  
Dominant Factor ◽  
High Speed Imaging ◽  
Lean Premixed Combustion ◽  
Fuel Jet ◽  
Image Velocimetry

The use of highly reactive fuels in the lean premixed combustion systems employed in stationary gas turbines can lead to many practical problems, such as unwanted autoignition in regions not designed for combustion. In the present study, autoignition characteristics for hydrogen, diluted with up to 30 vol. % nitrogen, were investigated at conditions relevant to reheat combustor operation (p = 15 bar, T >1000 K, hot flue gas, relevant residence times). The experiments were performed in a generic, optically accessible reheat combustor, by applying high-speed imaging and particle image velocimetry. Autoignition limits for different mixing section (temperature, velocity) and fuel jet (N2 dilution) parameters are described. The dominant factor influencing autoignition was the temperature, with an increase of around 2% leading to a reduction of the highest possible H2 concentration without “flame-stabilizing autoignition kernels” of approximately 16 vol. %. Furthermore, the onset and propagation of the ignition kernels were elucidated using the high-speed measurements. It was found that the ability of individual autoignition kernels to develop into stable flames depends on the initial position of the kernel and the corresponding axial velocity at that position. While unwanted autoignition occurred prior to reaching the desired operating point for most investigated conditions, for certain conditions the reheat combustor could be operated stably with up to 80 vol. % H2 in the fuel.

Autoignition Limits of Hydrogen at Relevant Reheat Combustor Operating Conditions

2011 ◽  
Author(s):  
Julia Fleck ◽  
Peter Griebel ◽  
Adam M. Steinberg ◽  
Michael Sto¨hr ◽  
Manfred Aigner ◽  
...  
Keyword(s):  
Flue Gas ◽  
Gas Turbines ◽  
High Speed ◽  
Initial Position ◽  
Operating Conditions ◽  
Dominant Factor ◽  
High Speed Imaging ◽  
Lean Premixed Combustion ◽  
Fuel Jet ◽  
Image Velocimetry

The use of highly reactive fuels in the lean premixed combustion systems employed in stationary gas turbines can lead to many practical problems, such as unwanted autoignition in regions not designed for combustion. In the present study, autoignition characteristics for hydrogen, diluted with up to 30 vol. % nitrogen, were investigated at conditions relevant to reheat combustor operation (p = 15 bar, T > 1000 K, hot flue gas, relevant residence times). The experiments were performed in a generic, optically accessible reheat combustor, by applying high-speed imaging and Particle Image Velocimetry (PIV). Autoignition limits for different mixing section (temperature, velocity) and fuel jet (N2 dilution) parameters are described. The dominant factor influencing autoignition was the temperature, with an increase of around 2% leading to a reduction of the highest possible H2 concentration without “flame-stabilizing autoignition kernels” of approximately 16 vol. %. Furthermore, the onset and propagation of the ignition kernels were elucidated using the high-speed measurements. It was found that the ability of individual autoignition kernels to develop into stable flames depends on the initial position of the kernel and the corresponding axial velocity at that position. While unwanted autoignition occurred prior to reaching the desired operating point for most investigated conditions, for certain conditions the reheat combustor could be operated stably with up to 80 vol. % H2 in the fuel.

scholarly journals The Influence of Carrier Air Preheating on Autoignition of Inline-Injected Hydrogen–Nitrogen Mixtures in Vitiated Air of High Temperature

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Christoph A. Schmalhofer ◽  
Peter Griebel ◽  
Manfred Aigner
Keyword(s):  
Hydrogen Content ◽  
Gas Turbines ◽  
High Speed ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
Promoting Effect ◽  
Experimental Conditions ◽  
Lean Premixed Combustion ◽  
Image Velocimetry ◽  
Fuel Mixtures

The use of highly reactive hydrogen-rich fuels in lean premixed combustion systems strongly affects the operability of stationary gas turbines (GT) resulting in higher autoignition and flashback risks. The present study investigates the autoignition behavior and ignition kernel evolution of hydrogen–nitrogen fuel mixtures in an inline co-flow injector configuration at relevant reheat combustor operating conditions. High-speed luminosity and particle image velocimetry (PIV) measurements in an optically accessible reheat combustor are employed. Autoignition and flame stabilization limits strongly depend on temperatures of vitiated air and carrier preheating. Higher hydrogen content significantly promotes the formation and development of different types of autoignition kernels: More autoignition kernels evolve with higher hydrogen content showing the promoting effect of equivalence ratio on local ignition events. Autoignition kernels develop downstream a certain distance from the injector, indicating the influence of ignition delay on kernel development. The development of autoignition kernels is linked to the shear layer development derived from global experimental conditions.

Influence of Carrier Air Preheating on Autoignition of Inline-Injected Hydrogen-Nitrogen Mixtures in Vitiated Air of High Temperature

2017 ◽  
Author(s):  
Christoph A. Schmalhofer ◽  
Peter Griebel ◽  
Manfred Aigner
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
Spatial Development ◽  
Design Guidelines ◽  
Operating Conditions ◽  
High Speed Imaging ◽  
Temporal And Spatial ◽  
Fuel Mixtures

Gas turbines will play a significant role in future power generation systems because they provide peak capacity due to their fast start-up capability and high operational flexibility. However, in order to meet the COP 21 goals, de-carbonization of as turbine fuels is required. Compared to natural gas operation, autoignition and flashback risks in gas turbines operated on hydrogen-rich fuels are higher which has to be taken into account for a proper gas turbine design. From investigations of these phenomena at relevant operating conditions with appropriate measurement techniques, e.g. high-speed imaging, the understanding of the non-stationary processes occurring during autoignition can be improved and design guidelines for a safe and reliable gas turbine operation can be derived. The present study investigates the influences of elevated carrier-air preheating temperatures and hydrogen fuel volume fractions on autoignition at hot gas temperatures higher than 1100 K and pressures of 15 bar. An in-line co-flow injector is used to inject the hydrogen-nitrogen fuel mixtures. The formation, temporal and spatial development of autoignition kernels at high-temperature vitiated air conditions, e.g. relevant to reheat combustor operation, are studied. The experiments were conducted in an optically accessible mixing section of a generic reheat combustor. The hydrogen-nitrogen fuel mixtures of up to 70 vol. % hydrogen are injected in-line into the mixing section along with the carrier-air which was preheated to temperatures between 303 K and 703 K. High-speed imaging was used to detect the autoignition kernels and their temporal and spatial development from luminescence signals. Particle Image Velocimetry measurements were conducted to obtain the velocity distribution in the mixing section at autoignition conditions. The influences of vitiated air temperatures and carrier preheating temperatures on autoignition and flame stabilisation limits are shown, alongside the spatial distribution of different types of autoignition kernels, developing at different stages of the autoignition process. The development of autoignition kernels could be linked to the shear layer development derived from global experimental conditions.

Experimental investigation of bubble formation and motion mechanism near the moonpool

2021 ◽  
pp. 147509022110449
Author(s):  
Xiongliang Yao ◽  
Xianghong Huang ◽  
Zeyu Shi ◽  
Wei Xiao ◽  
Kainan Huang
Keyword(s):  
High Speed ◽  
Bubble Formation ◽  
Similarity Criteria ◽  
Dominant Factor ◽  
Acoustic Detection ◽  
Prototype Test ◽  
Tracer Particles ◽  
Research Ship ◽  
Image Velocimetry ◽  
Ventilation Method

When a research ship sails at a high speed, there is relative motion between the ship and fluid. The ship is slammed by the fluid. To reduce the direct impact of the fluid, sonar is installed in the moonpool, and acoustic detection equipment is installed along the research ship bottom behind the moonpool. However, during high-speed sailing, a large number of bubbles form in the moonpool. Some bubbles escape from the moonpool and flow backward along the bottom of the ship. When a large number of bubbles are around the sonar and acoustic detection equipment, the equipment malfunctions. However, there have been few studies on bubble formation in the moonpool with sonar and distribution along the ship bottom behind the moonpool. Therefore, a related model was developed and prototype tests were carried out in this study. The appropriate similarity criteria were selected and verified to ensure the reliability of the experiment. Considering the influences of speed, sonar, moonpool shape, and draft, the reason and mechanism of bubble formation in a sonar moonpool were studied. An artificial ventilation method was used to simulate a real navigation environment. Because the bubbles are in a bright state under laser irradiation, the bubbles can be used as tracer particles. A high-speed camera captured illuminated bubbles. The distribution mechanism of bubbles along the ship bottom behind the moonpool was investigated using particle image velocimetry under the influence of the moonpool shape and sailing speed. The model experimental results agreed well with those of the prototype test. The air sucked into the water was the dominant factor in bubble formation in the moonpool. The bubbles were distributed in a W shape under the ship bottom.

scholarly journals Measurement of Air-Fuel Ratio Fluctuations Caused by Combustor Driven Oscillations

1998 ◽  
Author(s):  
Rajiv Mongia ◽  
Robert Dibble ◽  
Jeff Lovett
Keyword(s):  
Power Spectrum ◽  
Mole Fraction ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Premixed Combustion ◽  
Pollutant Emissions ◽  
Combustion Instabilities ◽  
Pressure Oscillations ◽  
Lean Premixed Combustion ◽  
Lean Premixed

Lean premixed combustion has emerged as a method of achieving low pollutant emissions from gas turbines. A common problem of lean premixed combustion is combustion instability. As conditions inside lean premixed combustors approach the lean flammability limit, large pressure variations are encountered. As a consequence, certain desirable gas turbine operating regimes are not approachable. In minimizing these regimes, combustor designers must rely upon trial and error because combustion instabilities are not well understood (and thus difficult to model). When they occur, pressure oscillations in the combustor can induce fluctuations in fuel mole fraction that can augment the pressure oscillations (undesirable) or dampen the pressure oscillations (desirable). In this paper, we demonstrate a method for measuring the fuel mole fraction oscillations which occur in the premixing section during combustion instabilities produced in the combustor that is downstream of the premixer. The fuel mole fraction in the premixer is measured with kHz resolution by the absorption of light from a 3.39 μm He-Ne laser. A sudden expansion combustor is constructed to demonstrate this fuel mole fraction measurement technique. Under several operating conditions, we measure significant fuel mole fraction fluctuations that are caused by pressure oscillations in the combustion chamber. Since the fuel mole fraction is sampled continuously, a power spectrum is easily generated. The fuel mole fraction power spectrum clearly indicates fuel mole fraction fluctuation frequencies are the same as the pressure fluctuation frequencies under some operating conditions.

scholarly journals Dual-camera system for high-speed imaging in particle image velocimetry

2012 ◽  
Vol 15 (3) ◽  
pp. 193-195 ◽  
Author(s):  
K. Hashimoto ◽  
A. Hori ◽  
T. Hara ◽  
S. Onogi ◽  
H. Mouri
Keyword(s):  
Particle Image Velocimetry ◽  
High Speed ◽  
Particle Image ◽  
High Speed Imaging ◽  
Camera System ◽  
Image Velocimetry

Fuel Influence on Targeted Gas Turbine Combustion Properties: Part I — Detailed Diagnostics

2014 ◽  
Author(s):  
Thomas Mosbach ◽  
Victor Burger ◽  
Barani Gunasekaran
Keyword(s):  
Gas Turbine ◽  
High Speed ◽  
Leading Edge ◽  
Operating Conditions ◽  
Optical Measurements ◽  
Test Facility ◽  
Research Centre ◽  
High Speed Imaging ◽  
Combustion Properties ◽  
First Results

The threshold combustion performance of different fuel formulations under simulated altitude relight conditions were investigated in the altitude relight test facility located at the Rolls-Royce plc. Strategic Research Centre in Derby, UK. The combustor employed was a twin-sector representation of an RQL gas turbine combustor. Eight fuels including conventional crude-derived Jet A-1 kerosene, synthetic paraffinic kerosenes (SPKs), linear paraffinic solvents, aromatic solvents and pure compounds were tested. The combustor was operated at sub-atmospheric air pressure of 41 kPa and air temperature of 265 K. The temperature of all fuels was regulated to 288 K. The combustor operating conditions corresponded to a low stratospheric flight altitude near 9 kilometres. The experimental work at the Rolls-Royce (RR) test-rig consisted of classical relight envelope ignition and extinction tests, and ancillary optical measurements: Simultaneous high-speed imaging of the OH* chemiluminescence and of the soot luminosity was used to visualize both the transient combustion phenomena and the combustion behaviour of the steady burning flames. Flame luminosity spectra were also simultaneously recorded with a spectrometer to obtain information about the different combustion intermediates and about the thermal soot radiation curve. This paper presents first results from the analysis of the weak extinction measurements. Further detailed test fuel results are the subject of a separate complementary paper [1]. It was found in general that the determined weak extinction parameters were not strongly dependent on the fuels investigated, however at the leading edge of the OH* chemiluminescence intensity development in the pre-flame region fuel-related differences were observed.

Investigation on Flat-Fan Spray Characterization in High-Speed Air Coflow for Gas Turbine Online Water Washing Application

2021 ◽  
Author(s):  
Kiran Kumar ◽  
Vasudev Chaudhari ◽  
Srikrishna Sahu ◽  
Ravindra G. Devi
Keyword(s):  
Droplet Size ◽  
Gas Turbines ◽  
High Speed ◽  
Numerical Models ◽  
Cone Angle ◽  
Operating Conditions ◽  
Spray Characteristics ◽  
Spray Cone ◽  
Water Washing ◽  
Spray Characterization

Abstract Fouling in compressor blades due to dirt deposition is a major issue in land-based gas turbines as it impedes the compressor performance and degrades the overall engine efficiency. The online water washing approach is an effective alternate for early-stage compressor blade cleaning and to optimize the time span between offline washing and peak availability. In such case, typically a series of flat-fan nozzles are used at the engine bell mouth to inject water sprays into the inflowing air. However, optimizing the injector operating conditions is not a straightforward task mainly due to the tradeoff between blade cleaning effectiveness and material erosion. In this context, the knowledge on spray characteristics prior to blade impingement play a vital role, and the experimental spray characterization is crucial not only to understand the basic process but also to validate numerical models and simulations. The present paper investigates spray characteristics in a single flat-fan nozzle operated in the presence of a coflowing air within a wind-tunnel. A parametric investigation is carried out using different air flow velocity in the tunnel and inlet water temperature, while the liquid flow rate was maintained constant. The spray cone angle and liquid breakup length are measured using back-lit photography. The high-speed shadowgraphy technique is used for capturing the droplet images downstream of the injector exit. The images are processed following depth-of-filed correction to measure droplet size distribution. Droplet velocity is measured by the particle tracking velocimetry (PTV) technique. As both droplet size and velocity are known, the cross-stream evolution of local droplet mass and momentum flux are obtained at different axial locations which form the basis for studying the effectiveness of the blade cleaning process due to droplet impingement on a coupon coated with foulant of known mass.

Experimental study of fibre breakup and shot formation in melt blowing nozzle designs

2020 ◽  
pp. 152808372094927 ◽  
Author(s):  
Ignacio Formoso ◽  
Alejandro Rivas ◽  
Gerardo Beltrame ◽  
Gorka S Larraona ◽  
Juan Carlos Ramos ◽  
...  
Keyword(s):  
Experimental Study ◽  
High Speed ◽  
Flux Ratio ◽  
Adhesive Bond ◽  
Operating Conditions ◽  
Nozzle Geometry ◽  
Dimensionless Temperature ◽  
Melt Blowing ◽  
High Speed Imaging ◽  
Adhesive Bonds

The high demand for quality in the manufacture of absorbent hygiene products requires the adhesive bonds between layers to be as uniform as possible. An experimental study was conducted on two industrial multihole melt blowing nozzle designs used for hot-melt adhesive applications for hygiene products, in order to study two defects that influence the quality of the adhesive bond: fibre breakup, resulting in contamination, and the presence of shots, undesirable lumps that end up in the finished product. To this end, the fibre dynamics were captured at the nozzle exit region by using high-speed imaging. From the results it was observed that die drool is the main source of shot formation, while fibre breakup occurs as a result of applying a sufficiently large force in the direction perpendicular to the fibre. In addition, three dimensionless parameters were defined, the first two being the air-polymer flux ratio and the dimensionless temperature ratio, both of which represent the operating conditions, and the remaining one being the force ratio, which represents the nozzle geometry. The effect of these parameters on fibre breakup and shot formation was studied and the results indicate that both the operating conditions and the nozzle geometry were responsible for the onset of the fibre breakup and for the formation of shots. More precisely, both defects turned out to be dominated by the air-polymer flux ratio and the air tilt angle. The results that emerge from this study are useful for the enhancement of industrial melt blowing nozzles.

A Comparison of Turbulence Levels From Particle Image Velocimetry and Constant Temperature Anemometry Downstream of a Low-Pressure Turbine Cascade at High-Speed Flow Conditions

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Silvio Chemnitz ◽  
Reinhard Niehuis
Keyword(s):  
Particle Image Velocimetry ◽  
Constant Temperature ◽  
High Speed ◽  
Particle Image ◽  
Low Pressure ◽  
Operating Conditions ◽  
Stereoscopic Particle Image Velocimetry ◽  
Turbine Cascade ◽  
Low Pressure Turbine ◽  
Image Velocimetry

Abstract The development and verification of new turbulence models for Reynolds-averaged Navier–Stokes (RANS) equation-based numerical methods require reliable experimental data with a deep understanding of the underlying turbulence mechanisms. High accurate turbulence measurements are normally limited to simplified test cases under optimal experimental conditions. This work presents comprehensive three-dimensional data of turbulent flow quantities, comparing advanced constant temperature anemometry (CTA) and stereoscopic particle image velocimetry (PIV) methods under realistic test conditions. The experiments are conducted downstream of a linear, low-pressure turbine cascade at engine relevant high-speed operating conditions. The special combination of high subsonic Mach and low Reynolds number results in a low density test environment, challenging for all applied measurement techniques. Detailed discussions about influences affecting the measured result for each specific measuring technique are given. The presented time mean fields as well as total turbulence data demonstrate with an average deviation of ΔTu<0.4% and ΔC/Cref<0.9% an extraordinary good agreement between the results from the triple sensor hot-wire probe and the 2D3C-PIV setup. Most differences between PIV and CTA can be explained by the finite probe size and individual geometry.

Sign in / Sign up

Export Citation Format

Share Document