Aerodynamic Performance of a Small Horizontal Axis Wind Turbine

2012 ◽  
Vol 134 (2) ◽  
Author(s):  
Maryam Refan ◽  
Horia Hangan
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
High Speed ◽  
Aerodynamic Performance ◽  
Horizontal Axis ◽  
Power Prediction ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Wide Range ◽  
Bem Theory

The aerodynamic performance of an upwind, three-bladed, small horizontal axis wind turbine (HAWT) rotor of 2.2 m in diameter was investigated experimentally and theoretically in order to assess the applicability of the blade element momentum (BEM) theory for modeling the rotor performance for the case of small HAWTs. The wind turbine has been tested in the low and high speed sections of the Boundary Layer Wind Tunnel 2 (BLWT2) at the University of Western Ontario (UWO) in order to determine the power curve over a wide range of wind speeds. Afterward, the BEM theory has been implemented to evaluate the rotor performance and to investigate three-dimensionality effects on power prediction by the theory. Comparison between the theoretical and experimental results shows that the overall prediction of the theory is within an acceptable range of accuracy. However, the BEM theory prediction for the case of small wind turbines is not as accurate as the prediction for larger wind turbines.

Analysis on Aerodynamic Performance of Horizontal Axis Wind Turbine Based on Nonlinear Wake Model

2013 ◽  
Vol 448-453 ◽  
pp. 1716-1720
Author(s):  
Rui Yang ◽  
Jiu Xin Wang ◽  
Sheng Long Zhang
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Optimization Design ◽  
Aerodynamic Performance ◽  
Horizontal Axis ◽  
Wake Vortex ◽  
Horizontal Axis Wind Turbine ◽  
Horizontal Axis Wind Turbines ◽  
Wake Model ◽  
Induced Velocity

A computational method based on nonlinear wake model was established for horizontal axis wind turbines aerodynamic performance prediction. This method makes use of finite difference method to solve the integral differential equation of the model, the induced velocity of wake vortex can be calculated from equations and compared with the induced velocity of wake vortex in linear model. The comparison between the calculated results of wind turbine under axis flow condition, including tip vortex geometry and aerodynamic performance, and available experimental data shows that this method is suitable for wind turbine aerodynamic performance analysis. Finally, a series of numerical calculations were made to investigate the change of wake geometry and aerodynamic performance of the wind turbine when yawing and pitch angle increasing, which provide foundations for aerodynamic optimization design of horizontal axis wind turbines.

scholarly journals Observation of the Starting and Low Speed Behavior of Small Horizontal Axis Wind Turbine

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Sikandar Khan ◽  
Kamran Shah ◽  
Izhar-Ul-Haq ◽  
Hamid Khan ◽  
Sajid Ali ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Starting Time ◽  
Speed Range ◽  
Horizontal Axis Wind Turbines ◽  
Starting Torque ◽  
High Angles Of Attack

This paper describes the starting behavior of small horizontal axis wind turbines at high angles of attack and low Reynolds number. The unfavorable relative wind direction during the starting time leads to low starting torque and more idling time. Wind turbine models of sizes less than 5 meters were simulated at wind speed range of 2 m/s to 5 m/s. Wind turbines were modeled in Pro/E and based on the optimized designs given by MATLAB codes. Wind turbine models were simulated in ADAMS for improving the starting behavior. The models with high starting torques and less idling times were selected. The starting behavior was successfully improved and the optimized wind turbine models were able to produce more starting torque even at wind speeds less than 5 m/s.

scholarly journals Aerodynamic performance simulation of three selected airfoils

2021 ◽  
Vol 25 (111) ◽  
pp. 201-211
Author(s):  
Mariana Montenegro Montero ◽  
Gustavo Richmond Navarro
Keyword(s):  
Renewable Energy ◽  
Turbulent Flow ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Aerodynamic Performance ◽  
Horizontal Axis ◽  
Wind Engineering ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Turbulence Effects

This work presents the lift and drag coefficient curves, as functions of the angle of attack, for the NACA0012, S809 and SG6043 airfoils in turbulent flow conditions. The objective is to identify the airfoil with the best aerodynamic performance under conditions that are descriptive of small scale wind turbine. With the use of OpenFOAM, an analysis was done by numerical simulation. In the case of the NACA0012 airfoil, it was found that the performance is insensitive to the changes in turbulence and the Reynold number. The aerodynamic response of the S809 airfoil is to increase both the drag and lift as the turbulence increases. The SG6043 airfoil responds the best out of the three in turbulent flow, given that the lift curves mostly increase with the turbulence. The curves reported in this work are new and not found in previous literature. Keywords: aerodynamics, lift, drag, turbulence References [1]R. Madriz-Vargas, A. Bruce, M. Watt, L. G. Mogollón and H. R. Álvarez, «Community renewable energy in Panama: a sustainability assessment of the “Bocade Lura” PV-Wind-Battery hybrid power system,» Renewable Energy and Environmental Sustainability, vol. 2, nº 18, pp. 1-7, 2017. https://doi.org/10.1051/rees/2017040. [2]S. Mertenes, «Wind Energy in the Built Environment, » Ph.D. dissertation. Multi-Science, Brentwood, 2006. [3]P. Giguere and M. S. Selig, «New airfoils for small horizontal axis wind turbines,» Journal of Solar Energy Engineering-transactions, vol. 120, pp. 108-114, 1988. https://doi.org/10.1115/1.2888052. [4]A. K. Wright and D. H. Wood, «The starting and low wind speed behaviour of a small horizontal axis wind turbine,» Journal of wind engineering and industrial aerodynamics, vol. 92, nº 14-15, pp. 1265-1279, 2004. https://doi.org/10.1016/j.jweia.2004.08.003. [5]G. Richmond-Navarro, M. Montenegro-Montero and C. Otárola, «Revisión de los perfiles aerodinámicos apropiados para turbinas eólicas de eje horizontal y de pequeña escala en zonas boscosas,» Revista Lasallista de Investigación, vol. 17, nº 1, pp. 233-251, 2020. https://doi.org/10.22507/rli.v17n1a22. [6]A. Tummala, R. K. Velamati, D. K. Sinha, V. Indraja and V. H. Krishna, «A review on small scale wind turbines, » Renewable and Sustainable Energy Reviews,vol. 56, pp. 1351-1371, 2016. https://doi.org/10.1016/j.rser.2015.12.027. [7]L. Pagnini, M. Burlando and M. Repetto, «Experimental power curve of small-size wind turbines in turbulent urban environment,» Applied Energy, vol. 154,pp. 112-121, 2015. https://doi.org/10.1016/j.apenergy. 2015.04.117. [8]W. D. Lubitz, «Impact of ambient turbulence on performance of a small wind turbine,» Renewable Energy, vol. 61, pp. 69-73, 2014. https://doi.org/10.1016/j.renene.2012.08.015. [9]P. Devinant, T. Laverne and J. Hureau, «Experimental study of wind-turbine airfoil aerodynamics in high turbulence, » Journal of Wind Engineering and Industrial Aerodynamics, vol. 90, nº 6, pp. 689-707, 2002. https://doi.org/10.1016/S0167-6105(02)00162-9. [10]C. Sicot, P. Devinant, S. Loyer and J. Hureau, «Rotational and turbulence effects on a wind turbine blade. Investigation of the stall mechanisms,» Journal ofwind engineering and industrial aerodynamics, vol. 96, nº 8-9, pp. 1320-1331, 2008. https://doi.org/10.1016/j.jweia.2008.01.013. [11]C. R. Chu and P. H. Chiang, «Turbulence effects on the wake flow and power production of a horizontal-axis wind turbine,» Journal of Wind Engineering and Industrial Aerodynamics, vol. 124, pp. 82-89, 2014. https://doi.org/10.1016/j.jweia.2013.11.001. [12]Y. Kamada, T. Maeda, J. Murata and Y. Nishida, «Visualization of the flow field and aerodynamic force on a Horizontal Axis Wind Turbine in turbulent inflows,» Energy, vol. 111, pp. 57-67, 2016. https://doi.org/10.1016/j.energy.2016.05.098. [13]Q. A. Li, J. Murata, M. Endo, T. Maeda and Y. Kamada, «Experimental and numerical investigation of the effect of turbulent inflow on a Horizontal Axis WindTurbine (Part I: Power performance),» Energy, vol.113, pp. 713-722, 2016. https://doi.org/10.1016/j.energy.2016.06.138. [14]S. W. Li, S. Wang, J. P. Wang and J. Mi, «Effect of turbulence intensity on airfoil flow: Numerical simulations and experimental measurements,» Applied Mathematics and Mechanics, vol. 32, nº 8, pp. 1029-1038, 2011. https://doi.org/10.1007/s10483-011-1478-8. [15]S. Wang, Y. Zhou, M. M. Alam and H. Yang, «Turbulent intensity and Reynolds number effects on an airfoil at low Reynolds numbers,» Physics of Fluids, vol. 26, nº11, p. 115107, 2014. https://doi.org/10.1063/1.4901969. [16]M. Lin and H. Sarlak, «A comparative study on the flow over an airfoil using transitional turbulence models, » AIP Conference Proceedings, vol. 1738, p.030050, 2016. https://doi.org/10.1063/1.4951806. [17]Langley Research Center, «Turbulence Modelling Resource,» NASA, [Online]. Available: https://turbmodels.larc.nasa.gov/langtrymenter_4eqn.html. [Last access: 08 03 2021].

scholarly journals Canard optimization for enhancing the performance of small horizontal axis wind turbine at low wind speeds

2020 ◽  
Vol 37 ◽  
pp. 63-71
Author(s):  
Yui-Chuin Shiah ◽  
Chia Hsiang Chang ◽  
Yu-Jen Chen ◽  
Ankam Vinod Kumar Reddy
Keyword(s):  
Wind Turbine ◽  
Urban Areas ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Peak Performance ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Optimum Parameters ◽  
Low Wind Speeds

ABSTRACT Generally, the environmental wind speeds in urban areas are relatively low due to clustered buildings. At low wind speeds, an aerodynamic stall occurs near the blade roots of a horizontal axis wind turbine (HAWT), leading to decay of the power coefficient. The research targets to design canards with optimal parameters for a small-scale HAWT system operated at variable rotational speeds. The design was to enhance the performance by delaying the aerodynamic stall near blade roots of the HAWT to be operated at low wind speeds. For the optimal design of canards, flow fields of the sample blades with and without canards were both simulated and compared with the experimental data. With the verification of our simulations, Taguchi analyses were performed to seek the optimum parameters of canards. This study revealed that the peak performance of the optimized canard system operated at 540 rpm might be improved by ∼35%.

scholarly journals Modeling and simulation of forces applied to the horizontal axis wind turbine rotors by the vortex method coupled with the method of the blade element

2021 ◽  
Vol 12 (1) ◽  
pp. 413
Author(s):  
Ibtissem Barkat ◽  
Abdelouahab Benretem ◽  
Fawaz Massouh ◽  
Issam Meghlaoui ◽  
Ahlem Chebel
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Farms ◽  
Vortex Method ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Rotor Blades ◽  
Good Representation ◽  
Horizontal Axis Wind Turbine ◽  
Blade Element

This article aims to study the forces applied to the rotors of horizontal axis wind turbines. The aerodynamics of a turbine are controlled by the flow around the rotor, or estimate of air charges on the rotor blades under various operating conditions and their relation to the structural dynamics of the rotor are critical for design. One of the major challenges in wind turbine aerodynamics is to predict the forces on the blade as various methods, including blade element moment theory (BEM), the approach that is naturally adapted to the simulation of the aerodynamics of wind turbines and the dynamic and models (CFD) that describes with fidelity the flow around the rotor. In our article we proposed a modeling method and a simulation of the forces applied to the horizontal axis wind rotors turbines using the application of the blade elements method to model the rotor and the vortex method of free wake modeling in order to develop a rotor model, which can be used to study wind farms. This model is intended to speed up the calculation, guaranteeing a good representation of the aerodynamic loads exerted by the wind.

scholarly journals New airfoils for micro horizontal-axis wind turbines

2021 ◽  
Author(s):  
Manoj Kumar Chaudhary ◽  
◽  
S. Prakash ◽  
Keyword(s):  
Reynolds Number ◽  
Wind Turbines ◽  
Low Reynolds Number ◽  
Horizontal Axis ◽  
Speed Ratio ◽  
Maximum Output ◽  
Horizontal Axis Wind Turbine ◽  
Horizontal Axis Wind Turbines ◽  
Low Reynolds ◽  
Bem Theory

In this study, small horizontal-axis wind turbine blades operating at low wind speeds were optimized. An optimized blade design method based on blade element momentum (BEM) theory was used. The rotor radius of 0.2 m, 0.4 m and 0.6 m and blade geometry with single (W1 & W2) and multistage rotor (W3) was examined. MATLAB and XFoil programs were used to implement to BEM theory and devise a six novel airfoil (NAF-Series) suitable for application of small horizontal axis wind turbines at low Reynolds number. The experimental blades were developed using the 3D printing additive manufacturing technique. The new airfoils such as NAF3929, NAF4420, NAF4423, NAF4923, NAF4924, and NAF5024 were investigated using XFoil software at Reynolds numbers of 100,000. The investigation range included tip speed ratios from 3 to 10 and angle of attacks from 2° to 20°. These parameters were varied in MATLAB and XFoil software for optimization and investigation of the power coefficient, lift coefficient, drag coefficient and lift-to-drag ratio. The cut-in wind velocity of the single and multistage rotors was approximately 2.5 & 3 m/s respectively. The optimized tip speed ratio, axial displacement and angle of attack were 5.5, 0.08m & 6° respectively. The proposed NAF-Series airfoil blades exhibited higher aerodynamic performances and maximum output power than those with the base SG6043 and NACA4415 airfoil at low Reynolds number.

scholarly journals Efficient contribution of partially tip cascaded horizontal-axis wind turbine

2019 ◽  
Vol 11 (11) ◽  
pp. 168781401989211
Author(s):  
Deyaa Nabil Elshebiny ◽  
Ali AbdelFattah Hashem ◽  
Farouk Mohammed Owis
Keyword(s):  
Wind Turbine ◽  
Aerodynamic Performance ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
National Renewable Energy Laboratory ◽  
Horizontal Axis Wind Turbine ◽  
Ansys Fluent ◽  
Knowing That ◽  
Turbine Performance ◽  
Blade Tip

This article introduces novel blade tip geometric modification to improve the aerodynamic performance of horizontal-axis wind turbine by adding auxiliary cascading blades toward the tip region. This study focuses on the new turbine shape and how it enhances the turbine performance in comparison with the classical turbine. This study is performed numerically for National Renewable Energy Laboratory Phase II (non-optimized wind turbine) taking into consideration the effect of adding different cascade configurations on the turbine performance using ANSYS FLUENT program. The analysis of single-auxiliary and double-auxiliary cascade blades has shown an impact on increasing the turbine power of 28% and 76%, respectively, at 72 r/min and 12.85 m/s of wind speed. Knowing that the performance of cascaded wind turbine depends on the geometry, solidity and operating conditions of the original blade; therefore, these results are not authorized for other cases.

Sign in / Sign up

Export Citation Format

Share Document