Numerical Studies on Effect of Channel Orientation in a Rotating Smooth Wedge-Shaped Cooling Channel

Author(s):  
Balamurugan Srinivasan ◽  
Anand Dhamarla ◽  
Chandiran Jayamurugan ◽  
Amarnath Balu Rajan

The increasing demands of better efficiency of modern advanced gas turbine require higher turbine inlet temperatures, which gives great challenges to turbine blade designers. However, the temperature limits of turbine blade material are not high enough to ensure its survival in such incredible operating temperature. Hence, both internal and external cooling approaches have been developed and widely used in today’s turbine blade. To internal cooling problems, a variety of cooling enhancement approaches, such as impingement and turbulators, are employed in order to meet the different needs in leading, middle and trailing region. One of the most critical parts in turbine blade is trailing edge where it is hard to cool due to its narrow shape. Pin-fins are widely used to cool the trailing edge of rotor and stator blades of gas turbine engine. Pin-fins offer significant heat transfer enhancement, they are relatively easy to fabricate and offer structural support to the hollow trailing edge region. The flow physics in a pin-fin roughened channel is very complicated and three-dimensional. In this work, we have studied the effect of channel orientation on heat transfer in a rotating wedge-shaped cooling channel using numerical methods. Qiu [1] studied experimentally heat transfer effects of 5 different angles of wedge shaped channel orientation for the inlet Reynolds number (5100 to 21000) and rotational speed (zero to 1000 rpm), which results in the inlet Rotation number variation from 0 to 0.68. They observed that compared to the non-rotating condition, there is about 35% overall heat transfer enhancement under highest rotation number. The above said results are validated using current studies with Computational Fluid Dynamics (CFD) revealed that rotation increases significantly the heat transfer coefficient on the trailing surface and reduces the heat transfer coefficient on the leading surface. This is due to the higher velocities associated with the converging geometry near trailing surface.

2021 ◽  
pp. 1-28
Author(s):  
Farah Nazifa Nourin ◽  
Ryoichi S. Amano

Abstract The study presents the investigation on heat transfer distribution along a gas turbine blade internal cooling channel. Six different cases were considered in this study, using the smooth surface channel as a baseline. Three different dimples depth-to-diameter ratios with 0.1, 0.25, and 0.50 were considered. Different combinations of partial spherical and leaf dimples were also studied with the Reynolds numbers of 6,000, 20,000, 30,000, 40,000, and 50,000. In addition to the experimental investigation, the numerical study was conducted using Large Eddy Simulation (LES) to validate the data. It was found that the highest depth-to-diameter ratio showed the highest heat transfer rate. However, there is a penalty for increased pressure drop. The highest pressure drop affects the overall thermal performance of the cooling channel. The results showed that the leaf dimpled surface is the best cooling channel based on the highest Reynolds number's heat transfer enhancement and friction factor. However, at the lowest Reynolds number, partial spherical dimples with a 0.25 depth to diameter ratio showed the highest thermal performance.


Author(s):  
Shuping P. Chen ◽  
Peiwen W. Li ◽  
Minking K. Chyu ◽  
Frank J. Cunha ◽  
William Abdel-Messeh

Described in this paper is an experimental study of heat transfer over a trailing edge configuration preceded with an internal cooling channel of pedestal array. The pedestal array consists of both circular pedestals and oblong shaped blocks. Downstream to the pedestal array, the trailing edge features pressure side cutback partitioned by the oblong shaped blocks. The local heat transfer coefficient over the entire wetted surface in the internal cooling chamber has been determined by using a “hybrid” measurement technique based on transient liquid crystal imaging. The hybrid technique employs the transient conduction model in a semi-infinite solid for resolving the heat transfer coefficient on the endwall surface uncovered by the pedestals. The heat transfer coefficient over a pedestal can be resolved by the lumped capacitance method with an assumption of low Biot number. The overall heat transfer for both the pedestals and endwalls combined shows a significant enhancement compared to the case with thermally developed smooth channel. Near the downstream most section of the suction side, the land, due to pressure side cutback, is exposed to the stream mixed with hot gas and discharged coolant. Both the adiabatic effectiveness and heat transfer coefficient on the land section are characterized by using the transient liquid crystal technique.


2021 ◽  
pp. 1-19
Author(s):  
Srivatsan Madhavan ◽  
Prashant Singh ◽  
Srinath V. Ekkad

Abstract Detailed heat transfer measurements using transient liquid crystal thermography were performed on a novel cooling design covering the mid-chord and trailing edge region of a typical gas turbine blade under rotation. The test section comprised of two channels with aspect ratio (AR) of 2:1 and 4:1, where the coolant was fed into the AR = 2:1 channel. Rib turbulators with a pitch-to-rib height ratio (p/e) of 10 and rib height-to-channel hydraulic diameter ratio (e/Dh) of 0.075 were placed in the AR = 2:1 channel at 60° relative to flow direction. The coolant after entering this section was routed to the AR = 4:1 section through a set of crossover jets. The 4:1 section had a realistic trapezoidal shape that mimics the trailing edge of an actual gas turbine blade. The pin fins were arranged in a staggered array with a center-to-center spacing of 2.5 times pin diameter. The trailing edge section consisted of radial and cutback exit holes for flow exit. Experiments were performed for Reynolds number of 20,000 at Rotation numbers (Ro) of 0, 0.1 and 0.14. The channel averaged heat transfer coefficient on trailing side was ~28% (AR = 2:1) and ~7.6% (AR = 4:1) higher than the leading side for Ro = 0.1. It is shown that the combination of crossover jets and pin-fins can be an effective method for cooling wedge shaped trailing edge channels over axial cooling flow designs.


Author(s):  
Maryam Pourhasanzadeh

In this research, numerical studies have been carried out for a film cooling jet on a gas turbine blade in the presence of different kinds of ribs. Simulations are performed for a film cooling jet inclined at 30-degrees. The effect of coolant jet velocity on convection heat transfer coefficient (h) is investigated. In addition, various ribs geometries and their distance from the blade surface are examined. It is shown that a combination of the rib and the film cooling jet stimulate the momentum and thermal boundary layers and subsequently improve the convection heat transfer coefficient. It is indicated that the heat transfer coefficient is dependent on the height of the rib and there is an inverse relation with the rib distance from the plate. Moreover, an increase in coolant jet velocity causes the increase of the heat transfer coefficient. The results show a significant improvement of the heat transfer coefficient over three times more than h on a blade without any ribs or coolant jet.


Author(s):  
Akhilesh P. Rallabandi ◽  
Yao-Hsien Liu ◽  
Je-Chin Han

The heat transfer characteristics of a rotating pin-fin roughened wedge shaped channel have been studied. The model incorporates ejection through slots machined on the narrower end of the wedge, simulating a rotor blade trailing edge. The copperplate regional average method is used to determine the heat transfer coefficient; pressure taps have been used to estimate the flow discharged through each slot. Tests have been conducted at high rotation (≈ 1 ) and buoyancy (≈ 2) numbers, in a pressurized rotating rig. Reynolds Numbers investigated range from 10,000 to 40,000 and rotational speeds range from 0–400rpm. Pin-fins studied are made of copper as well as non-conducting garolite. Results show high heat transfer coefficients in the proximity of the slot. A significant enhancement in heat transfer due to the pin-fins, compared with a smooth channel is observed. Even the non-conducting pin-fins, indicative of heat transfer on the end-wall show a significant enhancement in the heat transfer coefficient. Results also show a strong rotation effect, increasing significantly the heat transfer coefficient on the trailing surface — and reducing the heat transfer on the leading surface.


2021 ◽  
Author(s):  
Srivatsan Madhavan ◽  
Prashant Singh ◽  
Srinath V. Ekkad

Abstract Detailed heat transfer measurements using transient liquid crystal thermography were performed on a novel cooling design covering the mid-chord and trailing edge region of a typical gas turbine blade under stationary and rotating conditions. The test section comprised of two channels with aspect ratio (AR) of 2:1 (mid-chord) and 4:1 (trailing edge), where the coolant was fed into the AR = 2:1 channel from the root. Rib turbulators with a pitch-to-rib height ratio (p/e) of 10 and rib height-to-channel hydraulic diameter ratio (e/Dh) of 0.075 were placed in the AR = 2:1 channel at an angle of 60° relative to the direction of flow. The coolant after entering this section was routed to the AR = 4:1 section through a set of crossover jets. The purpose of the crossover jets was to induce sideways impingement onto the pin fins that were placed in the 4:1 section to enhance heat transfer. The 4:1 section had a realistic trapezoidal shape that mimics the trailing edge of an actual gas turbine blade. The pin fins were arranged in a staggered array with a center-to-center spacing of 2.5 times the pin diameter in both spanwise and streamwise directions. The trailing edge section consisted of both radial and cutback exit holes for flow exit. Experiments were performed for a Reynolds number (ReDh(AR = 2:1)) of 20,000 at Rotation numbers (RoDh(AR = 2:1)) of 0, 0.1 and 0.14. The channel averaged heat transfer coefficient on trailing side was ∼28% (AR = 2:1) and ∼7.6% (AR = 4:1) higher than the leading side for Rotation number (Ro) of 0.1. It is shown that the combination of crossover jets and pin-fins can be an effective method for cooling wedge shaped trailing edge channels over axial cooling flow designs.


2020 ◽  
Vol 1 (1) ◽  
pp. 16-21
Author(s):  
Agus Jamaldi ◽  
Hassan Khamis Hassan

This study aims to evaluate the performance of the trailing-edge (TE) cooling system in a gas turbine blade. Eddy Simulation (DES), based on the turbulence model of Spallart-Almaras (SA), was used to simulate the TE cooling system. A TE configuration with a five-row staggered pin-fin arrangement was employed as a computational domain. Three parameters, i.e., the coefficient of heat transfer on the pin-fins surface (hpin), the coefficient of discharge (CD), and the effectiveness of adiabatic film cooling were used to assess the performances. The findings denoted that the heat transfer fluctuations occurred on the surface of the pin-fins in each row. The discharge coefficient increased with the rising of the blowing ratio. The trend predicted data of effectiveness were in good agreement with realistic discrepancies compared to other researches, mainly for higher blowing ratio. The average effectiveness along the cut-off region was to be sensitive to the changes of the blowing ratio, which was attributed to the structures of turbulent flow along the mixing region.


Energies ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7968
Author(s):  
Jin Young Jeong ◽  
Woojun Kim ◽  
Jae Su Kwak ◽  
Byung Ju Lee ◽  
Jin Taek Chung

This study experimentally investigated the effects of cascade inlet velocity on the distribution and the level of the heat transfer coefficient on a gas turbine blade tip. The tests were conducted in a transient turbine test facility at Korea Aerospace University, and three cascade inlet velocities—30, 60, and 90 m/s—were considered. The heat transfer coefficient was measured using the transient IR camera technique with a linear regression method, and both the squealer and plane tips were investigated. The results showed that the overall averaged heat transfer coefficient was generally proportional to the inlet velocity. As the inlet velocity is increased from 30 m/s to 60 m/s and 90 m/s, the heat transfer coefficient increased by 11.4% and 25.0% for plane tip, and 26.6% and 64.1% for squealer tip, respectively. However, the heat transfer coefficient near the leading edge of the squealer tip and the reattachment region of the plane tip was greatly affected by the cascade inlet velocity. Therefore, heat transfer experiments for a gas turbine blade tip should be performed under engine simulating conditions.


Author(s):  
Gm S. Azad ◽  
Je-Chin Han ◽  
Robert J. Boyle

Experimental investigations are performed to measure the detailed heat transfer coefficient and static pressure distributions on the squealer tip of a gas turbine blade in a five-bladed stationary linear cascade. The blade is a 2-dimensional model of a modern first stage gas turbine rotor blade with a blade tip profile of a GE-E3 aircraft gas turbine engine rotor blade. A squealer (recessed) tip with a 3.77% recess is considered here. The data on the squealer tip are also compared with a flat tip case. All measurements are made at three different tip gap clearances of about 1%, 1.5%, and 2.5% of the blade span. Two different turbulence intensities of 6.1% and 9.7% at the cascade inlet are also considered for heat transfer measurements. Static pressure measurements are made in the mid-span and near-tip regions, as well as on the shroud surface opposite to the blade tip surface. The flow condition in the test cascade corresponds to an overall pressure ratio of 1.32 and an exit Reynolds number based on the axial chord of 1.1×106. A transient liquid crystal technique is used to measure the heat transfer coefficients. Results show that the heat transfer coefficient on the cavity surface and rim increases with an increase in tip clearance. The heat transfer coefficient on the rim is higher than the cavity surface. The cavity surface has a higher heat transfer coefficient near the leading edge region than the trailing edge region. The heat transfer coefficient on the pressure side rim and trailing edge region is higher at a higher turbulence intensity level of 9.7% over 6.1% case. However, no significant difference in local heat transfer coefficient is observed inside the cavity and the suction side rim for the two turbulence intensities. The squealer tip blade provides a lower overall heat transfer coefficient when compared to the flat tip blade.


Sign in / Sign up

Export Citation Format

Share Document