Pressure Sensitivity of HCCI Auto-Ignition Temperature for Oxygenated Reference Fuels

2012 ◽  
Author(s):  
Ida Truedsson ◽  
Martin Tuner ◽  
Bengt Johansson ◽  
William Cannella
Keyword(s):  
Compression Ratio ◽  
Ignition Temperature ◽  
Equivalence Ratio ◽  
Engine Speed ◽  
Pressure Sensitivity ◽  
Hcci Combustion ◽  
Air Temperatures ◽  
Auto Ignition ◽  
Temperature Heat ◽  
Pressure Trace

The current research focuses on creating an HCCI fuel index suitable for comparing different fuels for HCCI operation. One way to characterize a fuel is to use the Auto-Ignition Temperature (AIT). The AIT can be extracted from the pressure trace. Another potentially interesting parameter is the amount of Low Temperature Heat Release (LTHR) that is closely connected to the ignition properties of the fuel. The purpose of this study was to map the AIT and amount of LTHR of different oxygenated reference fuels in HCCI combustion at different cylinder pressures. Blends of n-heptane, iso-octane and ethanol were tested in a CFR engine with variable compression ratio. Five different inlet air temperatures ranging from 50°C to 150°C were used to achieve different cylinder pressures and the compression ratio was changed accordingly to keep a constant combustion phasing, CA50, of 3±1° after TDC. The experiments were carried out in lean operation with a constant equivalence ratio of 0.33 and with a constant engine speed of 600 rpm. The amount of ethanol needed to suppress LTHR from different PRFs was evaluated. The AIT and the amount of LTHR for different combinations of n-heptane, iso-octane and ethanol were charted.

Pressure Sensitivity of HCCI Auto-Ignition Temperature for Oxygenated Reference Fuels

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Ida Truedsson ◽  
Martin Tuner ◽  
Bengt Johansson ◽  
William Cannella
Keyword(s):  
Compression Ratio ◽  
Ignition Temperature ◽  
Engine Speed ◽  
Hcci Combustion ◽  
Air Temperatures ◽  
Auto Ignition ◽  
Temperature Heat ◽  
Pressure Trace ◽  
Primary Reference ◽  
Primary Reference Fuels

The current research focuses on creating a homogeneous charge compression ignition (HCCI) fuel index suitable for comparing different fuels for HCCI operation. One way to characterize a fuel is to use the auto-ignition temperature (AIT). The AIT can be extracted from the pressure trace. Another potentially interesting parameter is the amount of low temperature heat release (LTHR) that is closely connected to the ignition properties of the fuel. The purpose of this study was to map the AIT and the amount of LTHR of different oxygenated reference fuels in HCCI combustion at different cylinder pressures. Blends of n-heptane, iso-octane, and ethanol were tested in a cooperative fuels research (CFR) engine with a variable compression ratio. Five different inlet air temperatures ranging from 50 °C to 150 °C were used to achieve different cylinder pressures and the compression ratio was changed accordingly to keep a constant combustion phasing, CA50, of 3 ± 1 deg after top dead center (TDC). The experiments were carried out in lean operation with a constant equivalence ratio of 0.33 and with a constant engine speed of 600 rpm. The amount of ethanol needed to suppress the LTHR from different primary reference fuels (PRFs) was evaluated. The AIT and the amount of LTHR for different combinations of n-heptane, iso-octane, and ethanol were charted.

Residual-effected homogeneous charge compression ignition at a low compression ratio using exhaust reinduction

2003 ◽  
Vol 4 (3) ◽  
pp. 163-177 ◽  
Author(s):  
P. A. Caton ◽  
A. J. Simon ◽  
J. C. Gerdes ◽  
C. F. Edwards
Keyword(s):  
Compression Ratio ◽  
Equivalence Ratio ◽  
Homogeneous Charge Compression Ignition ◽  
Compression Ignition ◽  
Single Digit ◽  
Hcci Combustion ◽  
Actuation System ◽  
Order Of Magnitude ◽  
No Emissions ◽  
Homogeneous Charge

Studies have been conducted to assess the performance of homogeneous charge compression ignition (HCCI) combustion initiated by exhaust reinduction from the previous engine cycle. Reinduction is achieved using a fully flexible electrohydraulic variable-valve actuation system. In this way, HCCI is implemented at low compression ratio without throttling the intake or exhaust, and without preheating the intake charge. By using late exhaust valve closing and late intake valve opening strategies, steady HCCI combustion was achieved over a range of engine conditions. By varying the timing of both valve events, control can be exerted over both work output (load) and combustion phasing. In comparison with throttled spark ignition (SI) operation on the same engine, HCCI achieved 25–55 per cent of the peak SI indicated work, and did so at uniformly higher thermal efficiency. This was accompanied by a two order of magnitude reduction in NO emissions. In fact, single-digit (ppm) NO emissions were realized under many load conditions. In contrast, hydrocarbon emissions proved to be significantly higher in HCCI combustion under almost all conditions. Varying the equivalence ratio showed a wider equivalence ratio tolerance at low loads for HCCI.

scholarly journals Compression Ratio Effect on Methane HCCI Combustion

1999 ◽  
Vol 121 (3) ◽  
pp. 569-574 ◽  
Author(s):  
S. M. Aceves ◽  
J. R. Smith ◽  
C. K. Westbrook ◽  
W. J. Pitz
Keyword(s):  
Compression Ratio ◽  
Equivalence Ratio ◽  
Recent Experimental Data ◽  
Ignition Process ◽  
Operational Conditions ◽  
Hcci Combustion ◽  
Intake Pressure ◽  
Inlet Manifold ◽  
Compression Ignition Combustion ◽  
Gas Recirculation

We have used the HCT (hydrodynamics, chemistry, and transport) chemical kinetics code to simulate HCCI (homogeneous charge compression ignition) combustion of methane-air mixtures. HCT is applied to explore the ignition timing, burn duration, NOx, production, gross indicated efficiency and gross IMEP of a supercharged engine (3 atm. intake pressure) with 14:1, 16:1 and 18:1 compression ratios at 1200 rpm. HCT has been modified to incorporate the effect of heat transfer and to calculate the temperature that results from mixing the recycled exhaust with the fresh mixture. This study uses a single reaction zone that varies as a function of crank angle. The ignition process is controlled by adjusting the intake equivalence ratio and the residual gas trapping (RGT). RGT is internal exhaust gas recirculation, which recycles both thermal energy and combustion product species. Adjustment of equivalence ratio and RGT is accomplished by varying the timing of the exhaust valve closure in either two-stroke or four-stroke engines. Inlet manifold temperature is held constant at 300 K. Results show that, for each compression ratio, there is a range of operational conditions that show promise of achieving the control necessary to vary power output while keeping indicated efficiency above 50 percent and NOx levels below 100 ppm. HCT results are also compared with a set of recent experimental data for natural gas.

Effect of Premixed Diesel Fuel on Partial HCCI Combustion Characteristics

2014 ◽  
Vol 663 ◽  
pp. 26-33
Author(s):  
Y.H. Teoh ◽  
H.H. Masjuki ◽  
M.A. Kalam ◽  
Muhammad Afifi Amalina ◽  
H.G. How
Keyword(s):  
Diesel Fuel ◽  
Engine Speed ◽  
Direct Injection ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Hcci Combustion ◽  
Light Duty ◽  
Auto Ignition ◽  
Ignition Characteristics

This study investigated the effects of premixed diesel fuel on the auto-ignition characteristics in a light duty compression ignition engine. A partial homogeneous chargecompression ignition (HCCI) engine was modified from a single cylinder, four-stroke, direct injection compression ignition engine. The partial HCCI is achieved by injecting diesel fuel into the intake port of the engine, while maintaining diesel fuel injected in cylinder for combustion triggering. The auto-ignition of diesel fuel has been studied at various premixed ratios from 0 to 0.60, under engine speed of 1600 rpm and 20Nm load. The results for performance, emissions and combustion were compared with those achieved without premixed fuel. From the heat release rate (HRR) profile which was calculated from in-cylinder pressure, it is clearly observed that two-stage and three-stage ignition were occurred in some of the cases. Besides, the increases of premixed ratio to some extent have significantly reduced in NO emission.

Numerical Investigation of Auto-Ignition Characteristics in Microstructured Catalytic Honeycomb Reactor for CH4–Air and CH4–H2–Air Mixtures

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
H. Kayed ◽  
A. Mohamed ◽  
M. Yehia ◽  
M. A. Nemitallah ◽  
M. A. Habib
Keyword(s):  
Flow Rate ◽  
Ignition Temperature ◽  
Reaction Front ◽  
Equivalence Ratio ◽  
Thermal Conditions ◽  
Flammability Limits ◽  
Transient Conditions ◽  
Auto Ignition ◽  
Transient Simulations ◽  
Ignition Characteristics

Stable ranges of auto-ignition for the microcombustion of CH4 and CH4–H2 mixtures are identified numerically in a platinum-coated microcatalytic honeycomb reactor. Steady and transient simulations under pseudo-auto-thermal conditions were performed to investigate the coupling phenomenon between combustion and heat transfer in such microburner using ANSYS 17.2 coupled with a detailed chemkin reaction mechanism. The model was validated utilizing the available data in the literature on a similar microreactor, and the results showed good agreements. A certain amount of heat is furnished from outside at constant temperature from an external electric furnace to investigate the variations of localized self-ignition temperature while changing the flow rate and mixture strength. It was found that the ignition temperature for CH4–air mixtures is not affected by the mass flow rate. However, the ignition temperature of CH4–H2 air mixtures decreases while increasing the flow rate. The effect of equivalence ratio was studied to demonstrate the variations of flammability limits of the present microreactor. The equivalence ratio required for auto-ignition of CH4–air mixtures was found to be in the range from 0.4 up to 0.85 at a flow rate of 9.5 g/s. The reaction front moved from upstream to downstream under transient conditions matching with the reported experimental behavior in the literature.

Simulating the homogeneous charge compression ignition process using a detailed kinetic model for n-heptane mixtures

2000 ◽  
Vol 1 (3) ◽  
pp. 281-289 ◽  
Author(s):  
J Kusaka ◽  
T Yamamoto ◽  
Y Daisho
Keyword(s):  
Compression Ratio ◽  
Homogeneous Charge Compression Ignition ◽  
Combustion Model ◽  
Ignition Process ◽  
Compression Ignition ◽  
Complete Combustion ◽  
Hcci Combustion ◽  
Excess Air ◽  
Auto Ignition ◽  
Homogeneous Charge

The homogeneous charge compression ignition (HCCI) combustion has been attracting growing attention in recent years due to its potential for simultaneous improvement of exhaust gas emissions and fuel consumption in diesel engines. For practical application of HCCI to internal combustion (IC) engines, precise control of auto-ignition of pre-mixtures during the compression stroke is inevitable. This paper discusses the auto-ignition processes in an HCCI engine operated with n-heptane/air mixtures using a zero-dimensional combustion model including a detailed kinetics. The model proposed is validated first by a comparison between calculated and experimental pressure diagrams, and then the effects of initial charge conditions, compression ratio and excess air ratio on ignition and combustion are investigated. It was found from the parametric study that HCCI combustion of n-heptane/air mixtures is classified into three types of combustion: complete combustion, only low-temperature reaction and misfire, depending on the compression ratio and excess air ratio at which the engine is operated. Finally, the major paths of the HCCI reaction occurring in the engine cylinder were clarified by a sensitivity analysis of chemical reactions involved in the HCCI reaction scheme.

Sign in / Sign up

Export Citation Format

Share Document