scholarly journals Effect of Premixed Fuel Preparation for Partially Premixed Combustion With a Low Octane Gasoline on a Light-Duty Multi-Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Adam Dempsey ◽  
Scott Curran ◽  
Robert Wagner ◽  
William Cannella
Keyword(s):  
High Pressure ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Premixed Combustion ◽  
Injection System ◽  
Injection Timing ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Partially Premixed Combustion ◽  
Injection Strategies

Gasoline compression ignition concepts with the majority of the fuel being introduced early in the cycle are known as partially premixed combustion (PPC). Previous research on single- and multi-cylinder engines has shown that PPC has the potential for high thermal efficiency with low NOx and soot emissions. A variety of fuel injection strategies has been proposed in the literature. These injection strategies aim to create a partially stratified charge to simultaneously reduce NOx and soot emissions while maintaining some level of control over the combustion process through the fuel delivery system. The impact of the direct injection strategy to create a premixed charge of fuel and air has not previously been explored, and its impact on engine efficiency and emissions is not well understood. This paper explores the effect of sweeping the direct injected pilot timing from −91° to −324° ATDC, which is just after the exhaust valve closes for the engine used in this study. During the sweep, the pilot injection consistently contained 65% of the total fuel (based on command duration ratio), and the main injection timing was adjusted slightly to maintain combustion phasing near top dead center. A modern four cylinder, 1.9 L diesel engine with a variable geometry turbocharger, high pressure common rail injection system, wide included angle injectors, and variable swirl actuation was used in this study. The pistons were modified to an open bowl configuration suitable for highly premixed combustion modes. The stock diesel injection system was unmodified, and the gasoline fuel was doped with a lubricity additive to protect the high pressure fuel pump and the injectors. The study was conducted at a fixed speed/load condition of 2000 rpm and 4.0 bar brake mean effective pressure (BMEP). The pilot injection timing sweep was conducted at different intake manifold pressures, swirl levels, and fuel injection pressures. The gasoline used in this study has relatively high fuel reactivity with a research octane number of 68. The results of this experimental campaign indicate that the highest brake thermal efficiency and lowest emissions are achieved simultaneously with the earliest pilot injection timings (i.e., during the intake stroke).

scholarly journals Effect of Premixed Fuel Preparation for Partially Premixed Combustion With a Low Octane Gasoline on a Light-Duty Multicylinder Compression Ignition Engine

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
Adam B. Dempsey ◽  
Scott Curran ◽  
Robert Wagner ◽  
William Cannella
Keyword(s):  
High Pressure ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Premixed Combustion ◽  
Injection System ◽  
Injection Timing ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Partially Premixed Combustion ◽  
Injection Strategies

Gasoline compression ignition (GCI) concepts with the majority of the fuel being introduced early in the cycle are known as partially premixed combustion (PPC). Previous research on single- and multicylinder engines has shown that PPC has the potential for high thermal efficiency with low NOx and soot emissions. A variety of fuel injection strategies have been proposed in the literature. These injection strategies aim to create a partially stratified charge to simultaneously reduce NOx and soot emissions while maintaining some level of control over the combustion process through the fuel delivery system. The impact of the direct injection (DI) strategy to create a premixed charge of fuel and air has not previously been explored, and its impact on engine efficiency and emissions is not well understood. This paper explores the effect of sweeping the direct injected pilot timing from −91 deg to −324 deg ATDC, which is just after the exhaust valve closes (EVCs) for the engine used in this study. During the sweep, the pilot injection consistently contained 65% of the total fuel (based on command duration ratio), and the main injection timing was adjusted slightly to maintain combustion phasing near top dead center. A modern four cylinder, 1.9 l diesel engine with a variable geometry turbocharger (VGT), high pressure common rail injection system, wide included angle injectors, and variable swirl actuations was used in this study. The pistons were modified to an open bowl configuration suitable for highly premixed combustion modes. The stock diesel injection system was unmodified, and the gasoline fuel was doped with a lubricity additive to protect the high pressure fuel pump and the injectors. The study was conducted at a fixed speed/load condition of 2000 rpm and 4.0 bar brake mean effective pressure (BMEP). The pilot injection timing sweep was conducted at different intake manifold pressures, swirl levels, and fuel injection pressures. The gasoline used in this study has relatively high fuel reactivity with a research octane number of 68. The results of this experimental campaign indicate that the highest brake thermal efficiency (BTE) and lowest emissions are achieved simultaneously with the earliest pilot injection timings (i.e., during the intake stroke).

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

Fuel Stratification and Partially Premixed Combustion With Neat n-Butanol in a Compression Ignition Engine

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Shouvik Dev ◽  
Tongyang Gao ◽  
Xiao Yu ◽  
Mark Ives ◽  
Ming Zheng
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Premixed Combustion ◽  
Injection Timing ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Stratification ◽  
Partially Premixed Combustion ◽  
Partially Premixed ◽  
Ci Engines

Homogeneous charge compression ignition (HCCI) has been considered as an ideal combustion mode for compression ignition (CI) engines due to its superb thermal efficiency and low emissions of nitrogen oxides (NOx) and particulate matter. However, a challenge that limits practical applications of HCCI is the lack of control over the combustion rate. Fuel stratification and partially premixed combustion (PPC) have considerably improved the control over the heat release profile with modulations of the ratio between premixed fuel and directly injected fuel, as well as injection timing for ignition initiation. It leverages the advantages of both conventional direct injection compression ignition and HCCI. In this study, neat n-butanol is employed to generate the fuel stratification and PPC in a single cylinder CI engine. A fuel such as n-butanol can provide additional benefits of even lower emissions and can potentially lead to a reduced carbon footprint and improved energy security if produced appropriately from biomass sources. Intake port fuel injection (PFI) of neat n-butanol is used for the delivery of the premixed fuel, while the direct injection (DI) of neat n-butanol is applied to generate the fuel stratification. Effects of PFI-DI fuel ratio, DI timing, and intake pressure on the combustion are studied in detail. Different conditions are identified at which clean and efficient combustion can be achieved at a baseline load of 6 bar IMEP. An extended load of 14 bar IMEP is demonstrated using stratified combustion with combustion phasing control.

scholarly journals Impact of injection strategies on combustion characteristics, efficiency and emissions of gasoline compression ignition operation in a heavy-duty multi-cylinder engine

2018 ◽  
Vol 21 (8) ◽  
pp. 1426-1440 ◽  
Author(s):  
Buyu Wang ◽  
Michael Pamminger ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
High Temperature ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Gas Recirculation ◽  
Direct Fuel Injection

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low-temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high-temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Furthermore, for high-temperature gasoline compression ignition, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high-temperature gasoline compression ignition combustion with port and direct injection. Engine testing was conducted at an engine speed of 1038 r/min and brake mean effective pressure of 1.4 MPa for three injection strategies, late pilot injection, early pilot injection, and port/direct fuel injection. The impact on engine performance and emissions with respect to varying the combustion phasing were quantified within this study. At the same combustion phasing, early pilot injection and port/direct fuel injection had an earlier start of combustion and higher maximum pressure rise rates than late pilot injection attributable to more premixed fuel from pilot or port injection; however, brake thermal efficiencies were higher with late pilot injection due to reduced heat transfer. Early pilot injection also exhibited the highest cylinder-to-cylinder variations due to differences in injector behavior as well as the spray/wall interactions affecting mixing and evaporation process. Overall, peak brake thermal efficiency of 46.1% and 46% for late pilot injection and port/direct fuel injection was achieved comparable to diesel baseline (45.9%), while early pilot injection showed the lowest brake thermal efficiency (45.3%).

Influence of fuel injection strategies on efficiency and particulate emissions of gasoline and ethanol blends in a turbocharged multi-cylinder direct injection engine

2019 ◽  
Vol 22 (1) ◽  
pp. 152-164 ◽  
Author(s):  
Ripudaman Singh ◽  
Taehoon Han ◽  
Mohammad Fatouraie ◽  
Andrew Mansfield ◽  
Margaret Wooldridge ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Multiple Injection ◽  
Fuel Mass ◽  
Direct Injection Engine ◽  
Fuel Blends ◽  
Ethanol Blends ◽  
Injection Strategies

The effects of a broad range of fuel injection strategies on thermal efficiency and engine-out emissions (CO, total hydrocarbons, NOx and particulate number) were studied for gasoline and ethanol fuel blends. A state-of-the-art production multi-cylinder turbocharged gasoline direct injection engine equipped with piezoelectric injectors was used to study fuels and fueling strategies not previously considered in the literature. A large parametric space was considered including up to four fuel injection events with variable injection timing and variable fuel mass in each injection event. Fuel blends of E30 (30% by volume ethanol) and E85 (85% by volume ethanol) were compared with baseline E0 (reference grade gasoline). The engine was operated over a range of loads with intake manifold absolute pressure from 800 to 1200 mbar. A combined application of ethanol blends with a multiple injection strategy yielded considerable improvement in engine-out particulate and gaseous emissions while maintaining or slightly improving engine brake thermal efficiency. The weighted injection spread parameter defined in this study, combined with the weighted center of injection timing defined in the previous literature, was found well suited to characterize multiple injection strategies, including the effects of the number of injections, fuel mass in each injection and the dwell time between injections.

Effect of Injection Timing on PPCI and MPCI Mode Fueled With Straight-Run Naphtha

2013 ◽  
Vol 136 (3) ◽  
Author(s):  
Hongqiang Yang ◽  
Shijin Shuai ◽  
Zhi Wang ◽  
Jianxin Wang
Keyword(s):  
Diesel Fuel ◽  
Single Injection ◽  
Operating Conditions ◽  
Premixed Combustion ◽  
Spray Combustion ◽  
Injection Timing ◽  
Soot Emission ◽  
Compression Ignition ◽  
Injection Strategy ◽  
Injection Strategies

Partially premixed compression ignition (PPCI) and multiple premixed compression ignition (MPCI) mode of straight-run naphtha have been investigated under different injection strategies. The MPCI mode is realized by the multiple premixed combustion processes in a sequence of “spray-combustion-spray-combustion” around the compression top dead center. The spray and combustion events are preferred to be completely separated, without any overlap in the temporal sequence in order to ensure the multiple-stage premixed compression ignition. The PPCI mode is well known as the “spray-spray-combustion” sequence, with the start of combustion separated from the end of injection. Straight-run naphtha with a research octane number (RON) of 58.8 is tested in a single cylinder compression ignition engine whose compression ratio is 16.7 and displacement is 0.5 l. Double and triple injection strategies are investigated as the last injection timing sweeping at 1.0 MPa IMEP and 1800 rpm conditions. The MPCI mode is achieved using the double injection strategy, but its soot emission is higher than the PPCI mode under triple injection strategy. This is mainly because of the lower RON of the straight-run naphtha and the ignition delay is too short to form an ideally premixed combustion process after the second injection of straight-run naphtha. Diesel fuel is also tested under the same operating conditions, except for employing a single injection strategy. The naphtha PPCI and MPCI mode both have lower fuel consumption and soot emission than diesel fuel single injection mode, but the THC emissions are both higher than that of diesel fuel.

scholarly journals Conversion of Liquid to Gaseous Fuel for Prevaporised Premixed Combustion in Gas Turbines

1997 ◽  
Author(s):  
Y. Wang ◽  
L. Reh ◽  
D. Pennell ◽  
D. Winkler ◽  
K. Döbbeling
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Liquid Fuel ◽  
Fuel Injection ◽  
Premixed Combustion ◽  
Fuel Oil ◽  
Injection System ◽  
Nox Emissions ◽  
Combustion Tests

Stationary gas turbines for power generation are increasingly being equipped with low emission burners. By applying lean premixed combustion techniques for gaseous fuels both NOx and CO emissions can be reduced to extremely low levels (NOx emissions <25vppm, CO emissions <10vppm). Likewise, if analogous premix techniques can be applied to liquid fuels (diesel oil, Oil No.2, etc.) in gas-fired burners, similar low level emissions when burning oils are possible. For gas turbines which operate with liquid fuel or in dual fuel operation, VPL (Vaporised Premixed Lean)-combustion is essential for obtaining minimal NOx-emissions. An option is to vaporise the liquid fuel in a separate fuel vaporiser and subsequently supply the fuel vapour to the natural gas fuel injection system; this has not been investigated for gas turbine combustion in the past. This paper presents experimental results of atmospheric and high-pressure combustion tests using research premix burners running on vaporised liquid fuel. The following processes were investigated: • evaporation and partial decomposition of the liquid fuel (Oil No.2); • utilisation of low pressure exhaust gases to externally heat the high pressure fuel vaporiser; • operation of ABB premix-burners (EV burners) with vaporised Oil No.2; • combustion characteristics at pressures up to 25bar. Atmospheric VPL-combustion tests using Oil No.2 in ABB EV-burners under simulated gas turbine conditions have successfully produced emissions of NOx below 20vppm and of CO below 10vppm (corrected to 15% O2). 5vppm of these NOx values result from fuel bound nitrogen. Little dependence of these emissions on combustion pressure bas been observed. The techniques employed also ensured combustion with a stable non luminous (blue) flame during transition from gaseous to vaporised fuel. Additionally, no soot accumulation was detectable during combustion.

Analysis of the Influence of Pilot Injection Timing on Diesel Combustion in an Optical Engine by the Two-Color Method

2013 ◽  
Author(s):  
Weilin Zeng ◽  
Xu He ◽  
Senjia Jin ◽  
Hai Liu ◽  
Xiangrong Li ◽  
...  
Keyword(s):  
Ignition Delay ◽  
High Speed ◽  
Fuel Injection ◽  
Injection System ◽  
High Speed Photography ◽  
Injection Timing ◽  
Pilot Injection ◽  
Diesel Combustion ◽  
Optical Engine ◽  
Combustion Duration

High-speed photography, two-color method, and thermodynamic analysis have been used to improve understanding of the influence of pilot injection timing on diesel combustion in an optical engine equipped with an electronically-controlled, common rail, high-pressure fuel injection system. The tests were performed at four different pilot injection timings (30 degree, 25 degree, 20 degree, and 15 degree CA BTDC) with the same main injection timing (5 degree CA BTDC), and under 100MPa injection pressure. The engine speed was selected at 1200 rev/min, and the whole injection mass was fixed as 27.4 mg/stroke. The experimental results showed that the pilot injection timing had a strong influence on ignition delay and combustion duration: advancing the pilot injection timing turned to prolong the ignition delay and shorten the combustion duration. The combustion images indicated that when pilot injection was advanced, the area of luminous flames decreased. The results of two-color method suggested pilot injection timing significantly impacted both the soot temperature distribution and soot concentration (KL factor) within the combustion chamber. 30 degree CA BTDC was the optimal pilot injection timing for in-cylinder soot reduction.

scholarly journals Investigation Into Reactivity Separation Between Direct Injected and Premixed Fuels in RCCI Combustion Mode

2019 ◽  
Author(s):  
Ziming Yan ◽  
Brian Gainey ◽  
Deivanayagam Hariharan ◽  
Benjamin Lawler
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Efficiency ◽  
High Reactivity ◽  
Injection System ◽  
Injection Timing ◽  
Nox Emissions ◽  
Light Duty ◽  
Primary Reference

Abstract This experimental study focuses on the effects of the reactivity separation between the port injected fuel and the direct injection fuel, the amount of external-cooled exhaust gas recirculation (EGR), and the direct injection timing of the high reactivity fuel on Reactivity Controlled Compression Ignition (RCCI) combustion. The experiments were conducted on a light-duty, single-cylinder diesel engine with a production GM/Isuzu engine head and piston and a retrofitted port fuel injection system. The global charge-mass equivalence ratio, ϕ′, was fixed at 0.32 throughout all of the experiments. To investigate the effects of the fuel reactivity separation, different Primary Reference Fuels (PRF) were port injected, with the PRF number varying from 50 to 90. To investigate the effects of EGR, an EGR range of 0 to 55% was used. To investigate the effects of the injection timing, an injection timing window of −65 to −45 degrees ATDC was chosen. The results indicate that there are several tradeoffs. First, decreasing the port injected fuel reactivity (increasing the PRF number) delays combustion phasing, decreases the combustion efficiency by up to 9%, increases the gross indicated thermal efficiency up to 22%, enhances the combustion sensitivity to the direct injection timing, and slightly increases the UHC, CO, and NOx emissions. Second, increasing the EGR percentage delays combustion phasing, lowers the peak heat release rate, and lowers the NOx emissions. The combustion efficiency first increases and then decreases with EGR percentage for high reactivity fuels (low PRF number), but only decreases for low reactivity fuels. Finally, delaying the injection timing advances combustion phasing and increases the combustion efficiency, but decreases the gross indicated thermal efficiency and increases the NOx emissions. Across all of the experiments, delays in CA50 increase the gross indicated thermal efficiency and decrease the combustion efficiency, which represents an inherent tradeoff for RCCI combustion on a light-duty engine.

Sign in / Sign up

Export Citation Format

Share Document