Experimental Modal Analysis of Rectangular and Circular Beams

2003 ◽  
Author(s):  
B. H. Emory ◽  
W. D. Zhu
Keyword(s):  
Boundary Conditions ◽  
Cross Sections ◽  
Natural Frequencies ◽  
Beam Theory ◽  
Mode Shapes ◽  
Euler Beam ◽  
Modal Assurance Criterion ◽  
Rectangular Beam ◽  
Circular Beam ◽  
A New Technique

Analytical and experimental methods are used to determine the natural frequencies and mode shapes of Aluminum 6061-T651 beams with rectangular and circular cross sections. A unique test stand is developed to provide the rectangular beam with different boundary conditions including clamped-free, clamped-clamped, clamped-pinned, and pinned-pinned. The first 10 bending frequencies and mode shapes for each set of boundary conditions are measured. The effects of the bolt torque on the measured frequencies of the rectangular beam are examined. The material properties of the circular beam, including the elastic modulus, shear modulus, and Poisson’s ratio, are determined by measuring its first 20 natural frequencies. A new technique is used to mount an accelerometer to measure the torsional modes of the circular beam. A roving hammer test is conducted to measure the first 10 mode shapes. The measured mode shapes of the circular and rectangular beams are compared with their thoretical predictions using the modal assurance criterion. The Timoshenko beam theory is shown to provide better predictions of the natural frequencies for the higher modes of the circular beam than the Bernoulli-Euler beam theory. The use of the rectangular and circular beam test stands as a teaching tool for undergraduate and graduate students is discussed.

scholarly journals Vibration analysis of multi-stepped and multi-damaged parabolic arches using GDQ

2014 ◽  
Vol 2 (1) ◽  
Author(s):  
Erasmo Viola ◽  
Marco Miniaci ◽  
Nicholas Fantuzzi ◽  
Alessandro Marzani
Keyword(s):  
Boundary Conditions ◽  
Cross Sections ◽  
Natural Frequencies ◽  
Equations Of Motion ◽  
Free Vibrations ◽  
Mode Shapes ◽  
Internal Boundary ◽  
Radius Of Curvature ◽  
Inertia Effects ◽  
Circular Arch

AbstractThis paper investigates the in-plane free vibrations of multi-stepped and multi-damaged parabolic arches, for various boundary conditions. The axial extension, transverse shear deformation and rotatory inertia effects are taken into account. The constitutive equations relating the stress resultants to the corresponding deformation components refer to an isotropic and linear elastic material. Starting from the kinematic hypothesis for the in-plane displacement of the shear-deformable arch, the equations of motion are deduced by using Hamilton’s principle. Natural frequencies and mode shapes are computed using the Generalized Differential Quadrature (GDQ) method. The variable radius of curvature along the axis of the parabolic arch requires, compared to the circular arch, a more complex formulation and numerical implementation of the motion equations as well as the external and internal boundary conditions. Each damage is modelled as a combination of one rotational and two translational elastic springs. A parametric study is performed to illustrate the influence of the damage parameters on the natural frequencies of parabolic arches for different boundary conditions and cross-sections with localizeddamage.Results for the circular arch, derived from the proposed parabolic model with the derivatives of some parameters set to zero, agree well with those published over the past years.

scholarly journals Natural Frequencies and Mode Shapes of Drill Pipe in Subsea Xmas Tree Installation

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Wensheng Xiao ◽  
Haozhi Qin ◽  
Jian Liu ◽  
Qi Liu ◽  
Junguo Cui ◽  
...  
Keyword(s):  
Boundary Conditions ◽  
Natural Frequencies ◽  
Drill Pipe ◽  
Beam Theory ◽  
Transformation Method ◽  
Variable Coefficients ◽  
Mode Shapes ◽  
Order Partial Differential Equation ◽  
Lumped Mass ◽  
Acceleration Sensors

In this study, experimental and numerical investigations on the vibration characteristics of a drill pipe during the lowering of a subsea Xmas tree were presented. A fourth-order partial differential equation with variable coefficients was established based on Euler–Bernoulli beam theory. The natural frequencies and mode shapes are obtained by using the differential transformation method. Four drill pipe models of different sizes were used in the experiments which were measured using piezoelectric acceleration sensors and fiber Bragg grating sensors, respectively. The factors that affect the natural frequencies and mode shapes, such as length, diameter, lumped mass, and boundary conditions, were analyzed. The results show that all factors have remarkable effects on the natural frequency, but changes in the length and diameter of the pipe have little effect on the mode shapes; the main factors affecting the mode shape are the boundary conditions and lumped mass. The results of the numerical calculation were validated by a comparison with the experimental results and showed good agreement.

Free Bending Vibrations of a Centrally Bonded Symmetric Double Lap Joint (or Symmetric Double Doubler Joint) With a Gap in Mindlin Plates or Panels

2007 ◽  
Author(s):  
U. Yuceoglu ◽  
O. Gu¨vendik ◽  
V. O¨zerciyes
Keyword(s):  
Boundary Conditions ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Shear Stresses ◽  
Lap Joint ◽  
Bending Vibrations ◽  
Joint System ◽  
Adhesive Layers ◽  
Bonded Joint ◽  
Free Bending

In this present study, the “Free Bending Vibrations of a Centrally Bonded Symmetric Double Lap Joint (or Symmetric Double Doubler Joint) with a Gap in Mindlin Plates or Panels” are theoretically analyzed and are numerically solved in some detail. The “plate adherends” and the upper and lower “doubler plates” of the “Bonded Joint” system are considered as dissimilar, orthotropic “Mindlin Plates” joined through the dissimilar upper and lower very thin adhesive layers. There is a symmetrically and centrally located “Gap” between the “plate adherends” of the joint system. In the “adherends” and the “doublers” of the “Bonded Joint” assembly, the transverse shear deformations and the transverse and rotary moments of inertia are included in the analysis. The relatively very thin adhesive layers are assumed to be linearly elastic continua with transverse normal and shear stresses. The “damping effects” in the entire “Bonded Joint” system are neglected. The sets of the dynamic “Mindlin Plate” equations of the “plate adherends”, the “double doubler plates” and the thin adhesive layers are combined together with the orthotropic stress resultant-displacement expressions in a “special form”. This system of equations, after some further manipulations, is eventually reduced to a set of the “Governing System of the First Order Ordinary Differential Equations” in terms of the “state vectors” of the problem. Hence, the final set of the aforementioned “Governing Systems of Equations” together with the “Continuity Conditions” and the “Boundary conditions” facilitate the present solution procedure. This is the “Modified Transfer Matrix Method (MTMM) (with Interpolation Polynomials). The present theoretical formulation and the method of solution are applied to a typical “Bonded Symmetric Double Lap Joint (or Symmetric Double Doubler Joint) with a Gap”. The effects of the relatively stiff (or “hard”) and the relatively flexible (or “soft”) adhesive properties, on the natural frequencies and mode shapes are considered in detail. The very interesting mode shapes with their dimensionless natural frequencies are presented for various sets of boundary conditions. Also, several parametric studies of the dimensionless natural frequencies of the entire system are graphically presented. From the numerical results obtained, some important conclusions are drawn for the “Bonded Joint System” studied here.

Hydroelastic Vibration of Rectangular Plates

1996 ◽  
Vol 63 (1) ◽  
pp. 110-115 ◽  
Author(s):  
Moon K. Kwak
Keyword(s):  
Boundary Conditions ◽  
Approximate Formula ◽  
Natural Frequencies ◽  
Mass Matrix ◽  
Ritz Method ◽  
Plate Boundary ◽  
Rigid Wall ◽  
Mode Shapes ◽  
Rectangular Plates ◽  
Virtual Mass

This paper is concerned with the virtual mass effect on the natural frequencies and mode shapes of rectangular plates due to the presence of the water on one side of the plate. The approximate formula, which mainly depends on the so-called nondimensionalized added virtual mass incremental factor, can be used to estimate natural frequencies in water from natural frequencies in vacuo. However, the approximate formula is valid only when the wet mode shapes are almost the same as the one in vacuo. Moreover, the nondimensionalized added virtual mass incremental factor is in general a function of geometry, material properties of the plate and mostly boundary conditions of the plate and water domain. In this paper, the added virtual mass incremental factors for rectangular plates are obtained using the Rayleigh-Ritz method combined with the Green function method. Two cases of interfacing boundary conditions, which are free-surface and rigid-wall conditions, and two cases of plate boundary conditions, simply supported and clamped cases, are considered in this paper. It is found that the theoretical results match the experimental results. To investigate the validity of the approximate formula, the exact natural frequencies and mode shapes in water are calculated by means of the virtual added mass matrix. It is found that the approximate formula predicts lower natural frequencies in water with a very good accuracy.

scholarly journals NASTRAN Analysis of a Turbine Blade and Comparison With Test and Field Data

1975 ◽  
Author(s):  
J. M. Allen ◽  
L. B. Erickson
Keyword(s):  
Turbine Blade ◽  
Natural Frequencies ◽  
Beam Theory ◽  
Mode Shapes ◽  
Stress Distributions ◽  
Free Standing ◽  
Element Analysis ◽  
Metallographic Examination ◽  
Stiffening Effect ◽  
Generalized Beam Theory

A NASTRAN finite element analysis of a free standing gas turbine blade is presented. The analysis entails calculation of the first four natural frequencies, mode shapes, and relative vibratory stresses, as well as deflections and stresses due to centrifugal loading. The stiffening effect of the centrifugal force field was accounted for by using NASTRAN’s differential stiffness option. Natural frequencies measured in a rotating test correlated well with computed results. Areas of maximum vibratory stress (fundamental mode) coincided with the three zones of crack initiation observed in a metallographic examination of a fatigue failure. Airfoil stress distributions were found to be significantly different from that predicted by generalized beam theory, especially near the airfoil-platform junction.

Natural Frequencies and Normal Modes of a Spinning Timoshenko Beam With General Boundary Conditions

1992 ◽  
Vol 59 (2S) ◽  
pp. S197-S204 ◽  
Author(s):  
Jean Wu-Zheng Zu ◽  
Ray P. S. Han
Keyword(s):  
Boundary Conditions ◽  
Mode Shape ◽  
Timoshenko Beam ◽  
Natural Frequencies ◽  
Normal Modes ◽  
Single Mode ◽  
Mode Shapes ◽  
Simulation Studies ◽  
Classical Boundary ◽  
First Time

A free flexural vibrations of a spinning, finite Timoshenko beam for the six classical boundary conditions are analytically solved and presented for the first time. Expressions for computing natural frequencies and mode shapes are given. Numerical simulation studies show that the simply-supported beam possesses very peculiar free vibration characteristics: There exist two sets of natural frequencies corresponding to each mode shape, and the forward and backward precession mode shapes of each set coincide identically. These phenomena are not observed in beams with the other five types of boundary conditions. In these cases, the forward and backward precessions are different, implying that each natural frequency corresponds to a single mode shape.

Magneto-electro-elastic vibration of moderately thick FG annular plates subjected to multi physical loads in thermal environment using GDQ method by considering neutral surface

2019 ◽  
Vol 233 (10) ◽  
pp. 2140-2159 ◽  
Author(s):  
Ehsan Arshid ◽  
Ali Kiani ◽  
Saeed Amir
Keyword(s):  
Boundary Conditions ◽  
Natural Frequencies ◽  
Thermal Environment ◽  
Differential Quadrature Method ◽  
Shear Deformation Theory ◽  
Elastic Vibration ◽  
Functionally Graded ◽  
Mode Shapes ◽  
Neutral Surface ◽  
Sensors And Actuators

The vibration analysis of an annular plate made up of functionally graded magneto-electro-elastic materials subjected to multi physical loads is presented. The plate is in thermal environment and temperature is distributed non-uniformly in its thickness direction. In addition, the plate is assumed moderately thick, the material properties vary through the thickness, and the exact neutral surface position is determined and took into account. According to Hamilton’s principle and the first-order shear deformation theory, the governing motion equations are extracted. Numerical results for various boundary conditions are obtained via the generalized differential quadrature method and are validated in simpler states with those of the literature. The effects of different parameters such as material property gradient index, multi physical loads, temperature variations, boundary conditions and geometric specifications of the plate on the natural frequencies and mode shapes are investigated. Temperature changes have little effect on the natural frequencies and the effect of electric potential on them is opposite of magnetic one. In other words, by increasing the magnetic potential, the rigidity of the plate increases too, and the frequency increases. The results of this study are useful to design more efficient sensors and actuators used in the smart or intelligent structures.

scholarly journals Natural Frequency Characteristics of the Beam with Different Cross Sections Considering the Shear Deformation Induced Rotary Inertia

2020 ◽  
Vol 10 (15) ◽  
pp. 5245
Author(s):  
Chunfeng Wan ◽  
Huachen Jiang ◽  
Liyu Xie ◽  
Caiqian Yang ◽  
Youliang Ding ◽  
...  
Keyword(s):  
Shear Deformation ◽  
Cross Sections ◽  
Timoshenko Beam ◽  
High Frequency ◽  
Natural Frequencies ◽  
Beam Theory ◽  
Equation Of Motion ◽  
Timoshenko Beam Theory ◽  
Rotary Inertia ◽  
Cross Sectional

Based on the classical Timoshenko beam theory, the rotary inertia caused by shear deformation is further considered and then the equation of motion of the Timoshenko beam theory is modified. The dynamic characteristics of this new model, named the modified Timoshenko beam, have been discussed, and the distortion of natural frequencies of Timoshenko beam is improved, especially at high-frequency bands. The effects of different cross-sectional types on natural frequencies of the modified Timoshenko beam are studied, and corresponding simulations have been conducted. The results demonstrate that the modified Timoshenko beam can successfully be applied to all beams of three given cross sections, i.e., rectangular, rectangular hollow, and circular cross sections, subjected to different boundary conditions. The consequence verifies the validity and necessity of the modification.

scholarly journals Wave Based Method for Free Vibration Analysis of Ring Stiffened Cylindrical Shell with Intermediate Large Frame Ribs

2013 ◽  
Vol 20 (3) ◽  
pp. 459-479 ◽  
Author(s):  
Meixia Chen ◽  
Jianhui Wei ◽  
Kun Xie ◽  
Naiqi Deng ◽  
Guoxiang Hou
Keyword(s):  
Cylindrical Shell ◽  
Free Vibration ◽  
Boundary Conditions ◽  
Natural Frequencies ◽  
Free Vibration Analysis ◽  
Structure Type ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Arbitrary Boundary ◽  
Stiffened Cylindrical Shell

Wave based method which can be recognized as a semi-analytical and semi-numerical method is presented to analyze the free vibration characteristics of ring stiffened cylindrical shell with intermediate large frame ribs for arbitrary boundary conditions. According to the structure type and the positions of discontinuities, the model is divided into different substructures whose vibration field is expanded by wave functions which are exactly analytical solutions to the governing equations of the motions of corresponding structure type. Boundary conditions and continuity equations between different substructures are used to form the final matrix to be solved. Natural frequencies and vibration mode shapes are calculated by wave based method and the results show good agreement with finite element method for clamped-clamped, shear diaphragm – shear diaphragm and free-free boundary conditions. Free vibration characteristics of ring stiffened cylindrical shells with intermediate large frame ribs are compared with those with bulkheads and those with all ordinary ribs. Effects of the size, the number and the distribution of intermediate large frame rib are investigated. The frame rib which is large enough is playing a role as bulkhead, which can be considered imposing simply supported and clamped constraints at one end of the cabin and dividing the cylindrical shell into several cabins vibrating separately at their own natural frequencies.

Sign in / Sign up

Export Citation Format

Share Document