FSI-Based Assessment of FAC-Caused Wall Thinned Piping

2009 ◽  
Author(s):  
Sun-Hye Kim ◽  
Yoon-Suk Chang ◽  
Young-Jin Kim
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Structural Integrity ◽  
Flow Characteristics ◽  
Limit Load ◽  
Bend Angle ◽  
Piping System ◽  
Integrity Assessment ◽  
Wall Thinning ◽  
Analysis Scheme

Lots of investigations on failures of wall thinned piping have been carried out since the accident of Surry unit 2 in USA. From these preceding efforts, flow accelerated corrosion (FAC) which is a kind of wall thinning phenomenon is revealed main factor of failure of pipes in nuclear power plants. However, there are a few researches which directly take into account of flow characteristics and geometric changes for stress assessment of FAC-caused wall thinned piping. In this paper, structural integrity assessment employing a fluid-structure interaction (FSI) analysis scheme is performed on pipes representing secondary piping system of PWR which consists of straight pipes and elbows of various bend angles. Prior to the assessment, CFD analyses are conducted to predict plausible wall thinning location by considering flow and geometric parameters such as bend angle and radius of elbow. Then, for typical pipe geometry, detailed limit load analyses are performed to calculate maximum stress caused by turbulence and velocity of flow near the wall thinned part. Through these kinds of detailed parametric analyses, effects of FSI were observed, which should be considered for assessment of FAC-caused wall thinned piping.

Plastic Limit Analysis of an Elbow with Various Wall-Thinning Geometries

2008 ◽  
Vol 385-387 ◽  
pp. 833-836
Author(s):  
Sang Min Lee ◽  
Young Hwan Choi ◽  
Hae Dong Chung ◽  
Yoon Suk Chang ◽  
Young Jin Kim
Keyword(s):  
Nuclear Power ◽  
Three Dimensional ◽  
Bending Moment ◽  
Limit Load ◽  
Nuclear Industry ◽  
Bend Angle ◽  
Piping System ◽  
Plastic Limit ◽  
Limit Loads ◽  
Wall Thinning

A piping system including straight pipes, elbows and tee branches in a nuclear power plant is mostly subjected to severe loading conditions with high temperature and pressure. In particular, the wall-thinning of an elbow due to flow accelerated corrosion is one of safety issues in the nuclear industry. In this respect, it is necessary to investigate the limit loads of an elbow with a wall-thinned part for evaluating integrity. In this paper, three dimensional plastic limit analyses are performed to obtain limit loads of an elbow with different bend angles as well as defect geometries under internal pressure and in-plane/out-of-plane bending moment. The limit loads are also compared with the results from limit load solutions of an uninjured elbow based on the von Mises yield criteria. Finally, the effects of significant factors, bend angle and defect shape, are quantified to estimate the exact load carrying capacity of an elbow during operation.

Experimental Investigation on Failure Estimation Method for Circumferentially Cracked Pipes Subjected to Combined Bending and Torsion Loads

2013 ◽  
Author(s):  
Yinsheng Li ◽  
Kunio Hasegawa ◽  
Michiya Sakai ◽  
Shinichi Matsuura ◽  
Naoki Miura
Keyword(s):  
Experimental Investigation ◽  
Pressure Vessel ◽  
Nuclear Power ◽  
Power Plants ◽  
Structural Integrity ◽  
Estimation Method ◽  
Bending Moment ◽  
Limit Load ◽  
Piping System ◽  
Torsion Moment

When a crack is detected in a nuclear piping system during in-service inspections, the failure estimation method provided in codes such as the ASME Boiler and Pressure Vessel Code Section XI or JSME Rules on Fitness-for-Service for Nuclear Power Plants can be applied to evaluate the structural integrity of the cracked pipe. In the current codes, the failure estimation method for circumferentially cracked pipes includes bending moment and axial force due to pressure. Torsion moment is not considered. The Working Group on Pipe Flaw Evaluation for the ASME Boiler and Pressure Vessel Code Section XI is developing guidance for combining torsion load within the existing solutions provided in Appendix C for bending and pressure loadings on a pipe. A failure estimation method for circumferentially cracked pipes subjected to general loading conditions including bending moment, internal pressure and torsion moment with general magnitude has been proposed based on analytical investigations on the limit load for cracked pipes. In this study, experimental investigation was conducted to confirm the applicability of the proposed failure estimation method. Experiments were carried out on 8-inch diameter Schedule 80 stainless steel pipes containing a circumferential surface crack. Based on the experimental results, the proposed failure estimation method was confirmed to be applicable to cracked pipes subjected to combined bending and torsion moments.

Limit Analysis of a Pipe Section With Non-Uniform Wall Thinning

2002 ◽  
Author(s):  
Keshab K. Dwivedy
Keyword(s):  
Limit Analysis ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Structural Integrity ◽  
Pipe Wall ◽  
Limit Load ◽  
Pipe Section ◽  
Wall Thinning ◽  
Uniform Wall

Certain process piping in nuclear and non-nuclear power plants undergo pipe wall thinning due to flow assisted corrosion (FAC). This localized mechanism of corrosion combined with erosion is complex. The potential degradation of the pipe wall depends upon the water chemistry, operating temperature and pressure, flow velocity, piping material and piping configuration. The management of FAC in a power plant is performed in the following basic steps: Identification of potential locations, UT inspection of locations and characterization of pipe wall thinning, and evaluation of wall thinning to establish structural integrity and/or repair/replacement. The section of the pipe is repaired or replaced if the structural integrity cannot be established until next scheduled inspection. In the past 15 years, FAC programs have been established in nuclear power plants. Structural integrity evaluation is a part of the program. Simplified methods and rules are established in ASME Section XI code and in several code cases for verifying structural integrity. Pressure design methods are formalized for uniform and non-uniform wall thinning. However, the limit analysis methods for moment loading in the code rules are formulated for uniform thinning of the wall for simplicity. FAC related wall thinning is truly non-uniform, and treating it as non-uniform in the analysis can show additional structural margin compared to analysis conservatively assuming a uniformly thinned wall. This paper has developed simple analytical formulation of limit load carrying capability of a pipe section with non-uniform thinning. The method of analysis is illustrated with examples of actual plant situations. The formulation developed here can be used with the ASME code method to extend remaining life of FAC degraded components until the plant can plan for repair or replacement. Thus the analytical tool can help the plant owners to save resources by performing repair and replacement in a planned manner.

Experimental Investigation of Failure Estimation Method for Circumferentially Cracked Pipes Subjected to Combined Bending and Torsion Moments

2014 ◽  
Vol 137 (2) ◽  
Author(s):  
Yinsheng Li ◽  
Kunio Hasegawa ◽  
Michiya Sakai ◽  
Shinichi Matsuura ◽  
Naoki Miura
Keyword(s):  
Experimental Investigation ◽  
Nuclear Power ◽  
Power Plants ◽  
Structural Integrity ◽  
Estimation Method ◽  
Bending Moment ◽  
Limit Load ◽  
Estimation Methods ◽  
Piping System ◽  
Steel Pipes

When a crack is detected in a nuclear piping system during in-service inspections, failure estimation method provided in codes such as ASME Boiler and Pressure Vessel Code Section XI or JSME Rules on Fitness-for-Service for Nuclear Power Plants can be applied to evaluate the structural integrity of the cracked pipe. In the current codes, the failure estimation method for circumferentially cracked pipes is applicable for both bending moment and axial force due to pressure. Torsion moment is not considered. Recently, two failure estimation methods for circumferentially cracked pipes subjected to combined bending and torsion moments were proposed based on analytical investigations on the limit load for cracked pipes. In this study, experimental investigation was conducted to confirm the applicability of the failure estimation method for cracked pipes subjected to bending and torsion moments. Experiments were carried out on 8-in. diameter Schedule 80 stainless steel pipes containing a circumferential surface crack. Based on the experimental results, the proposed failure estimation methods were confirmed to be applicable to cracked pipes subjected to combined bending and torsion moments.

Load Factor for Evaluating Non-Planar Flaws in Carbon Steel Piping Using Limit Load Methodology

2016 ◽  
Author(s):  
Phuong H. Hoang
Keyword(s):  
Carbon Steel ◽  
Nuclear Power ◽  
Power Plants ◽  
Pipe Wall ◽  
Local Strain ◽  
Limit Load ◽  
Evaluation Methodology ◽  
Load Factor ◽  
Wall Thinning ◽  
Steel Piping

Non-planar flaw such as local wall thinning flaw is a major piping degradation in nuclear power plants. Hundreds of piping components are inspected and evaluated for pipe wall loss due to flow accelerated corrosion and microbiological corrosion during a typical scheduled refueling outage. The evaluation is typically based on the original code rules for design and construction, and so often that uniformly thin pipe cross section is conservatively assumed. Code Case N-597-2 of ASME B&PV, Section XI Code provides a simplified methodology for local pipe wall thinning evaluation to meet the construction Code requirements for pressure and moment loading. However, it is desirable to develop a methodology for evaluating non-planar flaws that consistent with the Section XI flaw evaluation methodology for operating plants. From the results of recent studies and experimental data, it is reasonable to suggest that the Section XI, Appendix C net section collapse load approach can be used for non-planar flaws in carbon steel piping with an appropriate load multiplier factor. Local strain at non-planar flaws in carbon steel piping may reach a strain instability prior to net section collapse. As load increase, necking starting at onset strain instability leads to crack initiation, coalescence and fracture. Thus, by limiting local strain to material onset strain instability, a load multiplier factor can be developed for evaluating non-planar flaws in carbon steel piping using limit load methodology. In this paper, onset strain instability, which is material strain at the ultimate stress from available tensile test data, is correlated with the material minimum specified elongation for developing a load factor of non-planar flaws in various carbon steel piping subjected to multiaxial loading.

Overview of Recent NUGENIA Activities Particularly in Relation to Structural Integrity

2015 ◽  
Author(s):  
John Sharples ◽  
Elisabeth Keim
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Structural Integrity ◽  
Nuclear Research ◽  
Joint Research ◽  
Non Profit ◽  
Integrity Assessment ◽  
Industry Research ◽  
Implementation And Dissemination ◽  
Technical Area

NUGENIA, an international non-profit association founded under Belgian legislation and launched in March 2012, is dedicated to nuclear research and development (R&D) with a focus on Generation II and III power plants. NUGENIA is the integrated framework between industry, research and safety organisations for safe, reliable and competitive nuclear power production, and is aimed at running an open innovation marketplace, to promote the emergence of joint research and to facilitate the implementation and dissemination of R&D results. The technical scope of NUGENIA consists of eight technical areas. One of these areas, Technical Area 4, is associated with the structural integrity assessment of systems, structures and components. A brief overview of recent NUGENIA activities in general is provided in this paper and a specific focus is given on developments in relation to Technical Area 4.

Nuclear Reactor Pressure Vessel Integrity Assessment: Enhancement Provided by 3D Modeling Flaw Stability Calculations

2013 ◽  
Author(s):  
Adolfo Arrieta-Ruiz ◽  
Eric Meister ◽  
Henriette Churier
Keyword(s):  
Pressure Vessel ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Structural Integrity ◽  
Reactor Pressure Vessel ◽  
Integrity Assessment ◽  
Potential Damage ◽  
Vessel Integrity ◽  
Reactor Pressure

Structural integrity of the Reactor Pressure Vessel (RPV) is one of the main considerations regarding safety and lifetime of Nuclear Power Plants (NPP) since this component is considered as not reasonably replaceable. Brittle fracture risk associated with the embrittlement of RPV steel in irradiated areas is the main potential damage. In France, deterministic integrity assessment for RPV is based on the crack initiation stage. The stability of an under-clad postulated flaw in the core area is currently evaluated under a Pressurized Thermal Shock (PTS) through a fracture mechanics simplified method. One of the axes of EDF’s implemented strategy for NPP lifetime extension is the improvement of the deterministic approach with regards to the input data and methods so as to reduce conservatisms. In this context, 3D finite element elastic-plastic calculations with flaw modelling have been carried out recently in order to quantify the enhancement provided by a more realistic approach in the most severe events. The aim of this paper is to present both simplified and 3D modelling flaw stability evaluation methods and the results obtained by running a small break LOCA event.

Structural Integrity Assessment of Doel 3 and Tihange 2 RPVs Affected by Hydrogen Flakes: Refined X-FEM Analyses

2016 ◽  
Author(s):  
Pierre Dulieu ◽  
Valéry Lacroix
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Extended Finite Element Method ◽  
Structural Integrity ◽  
Pressure Vessels ◽  
Extended Finite Element ◽  
Integrity Assessment ◽  
Safety Case ◽  
Component Manufacturing ◽  
Reactor Pressure

During the 2012 outage at Doel 3 and Tihange 2 Nuclear Power Plants, specific ultrasonic in-service inspections revealed a large number of quasi-laminar indications in the base metal of the reactor pressure vessels, mainly in the lower and upper core shells. The observed indications could subsequently be attributed to hydrogen flaking induced during the component manufacturing process. As a consequence, a Flaw Acceptability Assessment had to be performed as a part of the Safety Case demonstrating the fitness-for-service of these units. In that framework, detailed analyses using eXtended Finite Element Method were conducted to model the specific character of hydrogen flakes. Their quasi-laminar orientation as well as their high density required setting up 3D multi-flaws model accounting for flaw interaction. These calculations highlighted that even the most penalizing flaw configurations are harmless in terms of structural integrity despite the consideration of higher degradation of irradiated material toughness.

Pressure Tests for Thickness Management of Wall Thinning Tees

2012 ◽  
Author(s):  
Kaina Teshima ◽  
Yoichi Iwamoto ◽  
Kiminobu Hojo ◽  
Tomoyuki Oka ◽  
Kunihiro Kobayashi ◽  
...  
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Structural Integrity ◽  
Outer Diameter ◽  
Test Results ◽  
Minimum Thickness ◽  
T Joints ◽  
Wall Thinning ◽  
Pressure Tests ◽  
Design Pressure

Although the minimum thickness of pipe wall required (tsr) of T-joints (tees) of class 2, 3 and lower classes of nuclear power plants in Japan is calculated from the design pressure and temperature, there is no rule or standard of wall thinning T-joints for thickness management. This paper describes the pressure tests procedure and six test results with parameters of T-joint geometry such as outer diameter D, thickness T and T/D to establish structural integrity of wall thinning T-joints. Based on the fracture surface observation, a ductile crack initiation of each test mock-ups was confirmed.

A Feasibility Study of Noncontact Ultrasonic Sensor for Nuclear Power Plant Inspection

2017 ◽  
Vol 3 (2) ◽  
Author(s):  
Akinori Tamura ◽  
Chenghuan Zhong ◽  
Anthony J. Croxford ◽  
Paul D. Wilcox
Keyword(s):  
Power Plant ◽  
Nuclear Power Plant ◽  
Nuclear Power ◽  
Power Plants ◽  
Pipe Wall ◽  
Thickness Measurement ◽  
Piping System ◽  
Wall Thinning ◽  
Plant Inspection ◽  
Ultrasonic Thickness

A pipe-wall thinning measurement is a key inspection to ensure the integrity of the piping system in nuclear power plants. To monitor the integrity of the piping system, a number of ultrasonic thickness measurements are manually performed during the outage of the nuclear power plant. Since most of the pipes are covered with an insulator, removing the insulator is necessary for the ultrasonic thickness measurement. Noncontact ultrasonic sensors enable ultrasonic thickness inspection without removing the insulator. This leads to reduction of the inspection time and reduced radiation exposure of the inspector. The inductively-coupled transducer system (ICTS) is a noncontact ultrasonic sensor system which uses electromagnetic induction between coils to drive an installed transducer. In this study, we investigated the applicability of an innovative ICTS developed at the University of Bristol to nuclear power plant inspection, particularly pipe-wall thinning inspection. The following experiments were performed using ICTS: thickness measurement performance, the effect of the coil separation, the effect of the insulator, the effect of different inspection materials, the radiation tolerance, and the measurement accuracy of wastage defects. These initial experimental results showed that the ICTS has the possibility to enable wall-thinning inspection in nuclear power plants without removing the insulator. Future work will address the issue of measuring wall-thinning in more complex pipework geometries and at elevated temperatures.

Sign in / Sign up

Export Citation Format

Share Document