scholarly journals Segment Stress Characteristics and Ground Deformation Caused by Constructing Closely Spaced Parallel Tunnels under a Complex Geological Condition

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Jianbing Lv ◽  
Zikun Li ◽  
Xiaodong Xie ◽  
Bing Fu ◽  
Helin Fu ◽  
...  
Keyword(s):  
Detrimental Effect ◽  
Ground Deformation ◽  
Element Model ◽  
Additional Stress ◽  
Fe Model ◽  
Geological Condition ◽  
Guangzhou City ◽  
Practical Project ◽  
Parallel Tunnel ◽  
Subway Construction

Ground deformation and additional stress on the segments of the firstly constructed tunnel may change significantly due to the construction of another tunnel, which is closely spaced with the existing one. A poor geotechnical condition possibly leads to the interaction between such closely spaced tunnels even making it harder to build such tunnels. A practical project located in Guangzhou City, China, consists of such two parallel tunnels with the smallest distance of 2.6 m, which sat on an upper-soft and lower-hard stratum. A 3D finite element model has been proposed to numerically investigate the behavior of these two parallel tunnels. The numerical results predicted by the FE model are in close agreement with that obtained from the field monitoring system, indicating the accuracy of the proposed FE model. The FE model was then used to further analyze the effect of reinforcing piles in eliminating the detrimental effect on both ground deformation and additional stress of the segments of the existing tunnel as a result of the construction of the new parallel tunnel. The research results obtained from the present paper can provide technical support and guidance for urban subway construction.

Numerical Simulation of Post-Construction Deformation Characteristics of Storage Oil Tank Ground

2013 ◽  
Vol 353-356 ◽  
pp. 593-596 ◽  
Author(s):  
Yan Mei Zhang ◽  
Xu Dong Zhang
Keyword(s):  
Permeability Coefficient ◽  
Pore Water Pressure ◽  
Ground Deformation ◽  
Water Pressure ◽  
Three Dimensional ◽  
Element Model ◽  
Additional Stress ◽  
Soil Parameters ◽  
Ground Settlement ◽  
Constrained Modulus

Ground soil was looked as porous medium, a three-dimensional finite element model of shell-liquid-foundation-ground was built, and the influence of soil parameters, filling liquid mode, and liquid height on the tank ground deformation was discussed. The research shows that the subsidence range caused by additional stress is the 0.3D range of the tank bottom edge outer; the influence of soil constrained modulus on settlement is remarkable, with constrained modulus decreasing, the tank ground settlement increases; with soil permeability coefficient decreasing, the tank ground settlement decreases; the ground settlement curve shape is decided by soil constrained modulus and permeability coefficient; the influence of filling liquid mode on the ground final settlement is very small ,but on the pore water pressure peak is remarkable.

Finite Element Analysis of the Distributed Vibration Absorbers for Structural Noise Control

2005 ◽  
Author(s):  
Ashwini Gautam ◽  
Chris Fuller ◽  
James Carneal
Keyword(s):  
Finite Element ◽  
Numerical Model ◽  
Base Plate ◽  
Element Model ◽  
Fe Model ◽  
Vibration Absorbers ◽  
Element Analysis ◽  
Poroelastic Media ◽  
Hexahedral Elements ◽  
Component Models

This work presents an extensive analysis of the properties of distributed vibration absorbers (DVAs) and their effectiveness in controlling the sound radiation from the base structure. The DVA acts as a distributed mass absorber consisting of a thin metal sheet covering a layer of acoustic foam (porous media) that behaves like a distributed spring-mass-damper system. To assess the effectiveness of these DVAs in controlling the vibration of the base structures (plate) a detailed finite elements model has been developed for the DVA and base plate structure. The foam was modeled as a poroelastic media using 8 node hexahedral elements. The structural (plate) domain was modeled using 16 degree of freedom plate elements. Each of the finite element models have been validated by comparing the numerical results with the available analytical and experimental results. These component models were combined to model the DVA. Preliminary experiments conducted on the DVAs have shown an excellent agreement between the results obtained from the numerical model of the DVA and from the experiments. The component models and the DVA model were then combined into a larger FE model comprised of a base plate with the DVA treatment on its surface. The results from the simulation of this numerical model have shown that there has been a significant reduction in the vibration levels of the base plate due to DVA treatment on it. It has been shown from this work that the inclusion of the DVAs on the base plate reduces their vibration response and therefore the radiated noise. Moreover, the detailed development of the finite element model for the foam has provided us with the capability to analyze the physics behind the behavior of the distributed vibration absorbers (DVAs) and to develop more optimized designs for the same.

scholarly journals Bond Behaviour of Near-Surface Mounted Strips in RC Beams—Experimental Investigation and Numerical Simulations

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4362
Author(s):  
Renata Kotynia ◽  
Hussien Abdel Baky ◽  
Kenneth W. Neale
Keyword(s):  
Concrete Strength ◽  
Element Model ◽  
Steel Reinforcement ◽  
Reinforcement Ratio ◽  
Experimental Program ◽  
Fe Model ◽  
Bond Behaviour ◽  
Near Surface ◽  
Cfrp Laminates ◽  
Near Surface Mounted

This paper presents an investigation of the bond mechanism between carbon fibre reinforced polymer (CFRP) laminates, concrete and steel in the near-surface mounted (NSM) CFRP-strengthened reinforced concrete (RC) beam-bond tests. The experimental program consisting of thirty modified concrete beams flexurally strengthened with NSM CFRP strips was published in. The effects of five parameters and their interactions on the ultimate load carrying capacities and the associated bond mechanisms of the beams are investigated in this paper with consideration of the following investigated parameters: beam span, beam depth, longitudinal tensile steel reinforcement ratio, the bond length of the CFRP strips and compressive concrete strength. The longitudinal steel reinforcement was cut at the beam mid-span in four beams to investigate a better assessment of the influence of the steel reinforcement ratio on the bond behaviour of CFRP to concrete bond behaviour. The numerical analysis implemented in this paper is based on a nonlinear micromechanical finite element model (FEM) that was used for investigation of the flexural behaviour of NSM CFRP-strengthened members. The 3D model based on advanced CFRP to concrete bond responses was introduced to modelling of tested specimens. The FEM procedure presents the orthotropic behaviour of the CFRP strips and the bond response between the CFRP and concrete. Comparison of the experimental and numerical results revealed an excellent agreement that confirms the suitability of the proposed FE model.

Numerical Analysis of Metro Station Construction by Large-Diameter Shield and Pile-Beam-Arch Method

2011 ◽  
Vol 368-373 ◽  
pp. 2711-2715 ◽  
Author(s):  
De Yun Ding ◽  
Xiu Ren Yang ◽  
Wei Dong Lu ◽  
Wei Ning Liu ◽  
Mei Yan ◽  
...  
Keyword(s):  
Ground Deformation ◽  
Large Diameter ◽  
Element Model ◽  
Construction Method ◽  
Shield Tunnel ◽  
Outer Diameter ◽  
Shield Tunneling ◽  
Metro Station ◽  
Dimensional Finite Element ◽  
New Construction

In more and more complicated urban building environment, a new construction method that metro engineering is constructed by large-diameter shield and shallow mining method can be regarded as a great attempt in China. By taking the Gaojiayuan station of Beijing metro line 14 as an engineering background, the main construction steps for the platform of the metro station built by a large-size shield with an outer diameter of 10 m and the Pile-Beam-Arch (PBA) method are introduced. Based on the soil-structure interaction theory, a two-dimensional finite element model is used to simulate the shield tunneling and the platform construction by the PBA method to enlarge the shield tunnel. The ground deformation and structural stress of the platform are predicted. The numerical results can be regarded as a valuable reference for the application of the new construction method in Beijing metro line 14.

Finite Element Model of Human Cochlea Considering of the Helicotrema Size

2013 ◽  
Vol 456 ◽  
pp. 576-581 ◽  
Author(s):  
Li Fu Xu ◽  
Na Ta ◽  
Zhu Shi Rao ◽  
Jia Bin Tian
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Basilar Membrane ◽  
Round Window ◽  
Element Model ◽  
Oval Window ◽  
Fe Model ◽  
Cochlear Duct ◽  
Human Cochlea ◽  
Set Up

A 2-D finite element model of human cochlea is established in this paper. This model includes the structure of oval window, round window, basilar membrane and cochlear duct which is filled with fluid. The basilar membrane responses are calculated with sound input on the oval window membrane. In order to study the effects of helicotrema on basilar membrane response, three different helicotrema dimensions are set up in the FE model. A two-way fluid-structure interaction numerical method is used to compute the responses in the cochlea. The influence of the helicotrema is acquired and the frequency selectivity of the basilar membrane motion along the cochlear duct is predicted. These results agree with the experiments and indicate much better results are obtained with appropriate helicotrema size.

A coupled FE model for the joint resolution of the shallow water and the groundwater flow equations

2014 ◽  
Vol 24 (7) ◽  
pp. 1553-1569 ◽  
Author(s):  
H.G. Rábade ◽  
P. Vellando ◽  
F. Padilla ◽  
R. Juncosa
Keyword(s):  
Groundwater Flow ◽  
Shallow Water ◽  
Free Surface Flow ◽  
Element Model ◽  
Surface Flow ◽  
Fe Model ◽  
Content Type ◽  
Flow Equations ◽  
Natural Watersheds ◽  
Joint Resolution

Purpose – A new coupled finite element model has been developed for the joint resolution of both the shallow water equations, that governs the free surface flow, and the groundwater flow equation that governs the motion of water through a porous media. The paper aims to discuss these issues. Design/methodology/approach – The model is based upon two different modules (surface and ground water) previously developed by the authors, that have been validated separately. Findings – The newly developed software allows for the assessment of the fluid flow in natural watersheds taking into account both the surface and the underground flow in the way it really takes place in nature. Originality/value – The main achievement of this work has dealt with the coupling of both models, allowing for a proper moving interface treatment that simulates the actual interaction that takes place between surface and groundwater in natural watersheds.

Finite Element Mesh Generator Applying Constraints’ Propagation and Isoparametric Mapping

1991 ◽  
Author(s):  
J. Rodriguez ◽  
M. Him
Keyword(s):  
Finite Element ◽  
Mesh Generation ◽  
Element Model ◽  
Finite Element Mesh ◽  
Fe Model ◽  
Element Analysis ◽  
Element Mesh ◽  
Mesh Generator ◽  
Generation Algorithm ◽  
Essential Input

Abstract This paper presents a finite element mesh generation algorithm (PREPAT) designed to automatically discretize two-dimensional domains. The mesh generation algorithm is a mapping scheme which creates a uniform isoparametric FE model based on a pre-partitioned domain of the component. The proposed algorithm provides a faster and more accurate tool in the pre-processing phase of a Finite Element Analysis (FEA). A primary goal of the developed mesh generator is to create a finite element model requiring only essential input from the analyst. As a result, the generator code utilizes only a sketch, based on geometric primitives, and information relating to loading/boundary conditions. These conditions represents the constraints that are propagated throughout the model and the available finite elements are uniformly mapped in the resulting sub-domains. Relative advantages and limitations of the mesh generator are discussed. Examples are presented to illustrate the accuracy, efficiency and applicability of PREPAT.

scholarly journals Condensation method in practical modal analysis of hull vibration with application of 3D FE model

2019 ◽  
pp. 162-169
Author(s):  
Valeriy Sutyrin
Keyword(s):  
Modal Analysis ◽  
Three Dimensional ◽  
Element Model ◽  
Fe Model ◽  
Structural Elements ◽  
Natural Vibrations ◽  
Condensation Method ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Analytical Approaches

This paper gives modal analysis results for mid-body of a refrigerator carrier ship by means of combined three-dimensional finite-element model with 1.5 million DOF. The study estimates the error of modal analysis for the ship structure if its boundary conditions are specified in advance, i.e. approximately, as well as analyses the gain in time offered by structuring the analytical model as per reduction (condensation) method. Analytical approaches thus transformed can be successfully applied in filtering lower frequencies and modes of natural vibrations for structural elements and joints of hull in the direct vicinity of exciting force application points.

scholarly journals The influence of edge effects on crack propagation in snow stability tests

2014 ◽  
Vol 8 (1) ◽  
pp. 229-257
Author(s):  
E. H. Bair ◽  
R. Simenhois ◽  
A. van Herwijnen ◽  
K. Birkeland
Keyword(s):  
Crack Propagation ◽  
Strain Energy ◽  
Wave Speed ◽  
Strain Energy Release Rate ◽  
Field Tests ◽  
Strain Energy Release ◽  
Element Model ◽  
Fe Model ◽  
Test Length ◽  
Column Tests

Abstract. Propagation tests are used to assess the likelihood of crack propagation in a snowpack, yet little is known about how test length affects propagation. Guidelines suggest beams with lengths around 1 m for Extended Column Tests (ECTs) and Propagation Saw Tests (PSTs). To examine how test length affects propagation, we performed 163 ECTs and PSTs 1 to 10 m long. On days with full crack propagation in 1.0 to 1.5 m tests, we then made videos of tests 2 to 10 m long. We inserted markers for particle tracking to measure collapse amplitude, collapse wave speed, and wavelength. We also used a finite element model to simulate the strain energy release rate at fixed crack lengths. We find that: (1) the proportion of tests with full propagation decreased with test length; (2) collapse was greater at the ends of the beams than in the centers; (3) collapse amplitudes in the longer tests were consistent with the shorter tests and did not reach a constant value; (4) collapse wavelengths in the longer tests were around 3 m, 2 × greater than what is predicted by the anticrack model. Based on our field tests and FE models, we conclude that the shorter tests fully propagated more frequently because of increased stress concentration from the far edge. The FE model suggests this edge effect occurs for PSTs up to 2 m long or a crack to beam length ratio ≥ 0.20. Our results suggest that ECT and PST length guidelines may need to be revisited.

scholarly journals Low Cost Frictional Seismic Base-Isolation of Residential New Masonry Buildings in Developing Countries: A Small Masonry House Case Study

2017 ◽  
Vol 11 (1) ◽  
pp. 1026-1035 ◽  
Author(s):  
Ahmad Basshofi Habieb ◽  
Gabriele Milani ◽  
Tavio Tavio ◽  
Federico Milani
Keyword(s):  
Finite Element ◽  
Seismic Vulnerability ◽  
Base Isolation ◽  
Low Cost ◽  
Element Model ◽  
Shaking Table ◽  
Fe Model ◽  
Isolation System ◽  
Finite Element Software ◽  
Non Linear

Introduction:An advanced Finite Element model is presented to examine the performance of a low-cost friction based-isolation system in reducing the seismic vulnerability of low-class rural housings. This study, which is mainly numerical, adopts as benchmark an experimental investigation on a single story masonry system eventually isolated at the base and tested on a shaking table in India.Methods:Four friction isolation interfaces, namely, marble-marble, marble-high-density polyethylene, marble-rubber sheet, and marble-geosynthetic were involved. Those interfaces differ for the friction coefficient, which was experimentally obtained through the aforementioned research. The FE model adopted here is based on a macroscopic approach for masonry, which is assumed as an isotropic material exhibiting damage and softening. The Concrete damage plasticity (CDP) model, that is available in standard package of ABAQUS finite element software, is used to determine the non-linear behavior of the house under non-linear dynamic excitation.Results and Conclusion:The results of FE analyses show that the utilization of friction isolation systems could much decrease the acceleration response at roof level, with a very good agreement with the experimental data. It is also found that systems with marble-marble and marble-geosynthetic interfaces reduce the roof acceleration up to 50% comparing to the system without isolation. Another interesting result is that there was little damage appearing in systems with frictional isolation during numerical simulations. Meanwhile, a severe state of damage was clearly visible for the system without isolation.

Sign in / Sign up

Export Citation Format

Share Document