Antimicrobial Poly(lactic acid)-Based Nanofibres Developed by Solution Blow Spinning

2015 ◽  
Vol 15 (1) ◽  
pp. 616-627 ◽  
Author(s):  
Marta Martínez-Sanz ◽  
Cristina Bilbao-Sainz ◽  
Wen-Xian Du ◽  
Bor-Sen Chiou ◽  
Tina G. Williams ◽  
...  
2013 ◽  
Vol 129 (6) ◽  
pp. 3672-3681 ◽  
Author(s):  
Juliano E. Oliveira ◽  
Eduardo A. Moraes ◽  
José M. Marconcini ◽  
Luiz H. C. Mattoso ◽  
Gregory M. Glenn ◽  
...  

2016 ◽  
Vol 51 (9) ◽  
pp. 4627-4638 ◽  
Author(s):  
Delne Domingos da Silva Parize ◽  
Milene Mitsuyuki Foschini ◽  
Juliano Elvis de Oliveira ◽  
Artur P. Klamczynski ◽  
Gregory Melvin Glenn ◽  
...  

2021 ◽  
pp. 113875
Author(s):  
Rafaella T. Paschoalin ◽  
Nathalia O. Gomes ◽  
Gabriela F. Almeida ◽  
Stanley Bilatto ◽  
Cristiane S. Farinas ◽  
...  

2014 ◽  
Vol 9 (4) ◽  
pp. 155892501400900 ◽  
Author(s):  
Juliano Oliveira ◽  
Glaúcia Silveira Brichi ◽  
José Manoel Marconcini ◽  
Luiz Henrique Capparelli Mattoso ◽  
Gregory Melvin Glenn ◽  
...  

Solution blow spinning (SBS) is a simple, safe, and inexpensive alternative to electrospinning for making nanofibers from polymer solutions. However, since SBS is a relatively new technique, there is a general lack of information on polymer solutions and properties that affect fiber morphology and intrinsic properties. The present study reports the solution properties of poly (lactic acid) (PLA) dissolved in chloroform, dichloromethane, and dichloroethane at 4%, 6%, or 8% (w/v) and the properties of fibers made by SBS. In contrast to 4% polymer solutions, fibers made from 6% polymer solutions had few beads and diameters in the range of 120–320 nm. Diameters were greater (311–570 nm) for fibers made from 8% polymer solutions. Solvent evaporation rate affected the fiber porosity and formation. Hansen solubility parameters indicate that dichloromethane was the solvent most miscible with PLA. Fibers made with PLA in dicloromethane had the broader range in fiber diameter. Hansen parameters could be a valuable predictive tool for identifying highly miscible polymer/solvent systems for the SBS process. Polymer solutions with high viscoelasticity and viscosity were well suited for the SBS process. Fibers made from polymer solutions containing dichloromethane had lower crystallinity compared to fibers made from the other solvents.


2016 ◽  
Vol 73 (11) ◽  
pp. 2973-2985 ◽  
Author(s):  
Rodrigo G. F. Costa ◽  
Glaucia S. Brichi ◽  
Caue Ribeiro ◽  
Luiz H. C. Mattoso

2016 ◽  
Vol 133 (18) ◽  
pp. n/a-n/a ◽  
Author(s):  
Delne Domingos da Silva Parize ◽  
Juliano Elvis de Oliveira ◽  
Milene Mitsuyuki Foschini ◽  
José Manoel Marconcini ◽  
Luiz Henrique Capparelli Mattoso

2017 ◽  
Vol 134 (19) ◽  
Author(s):  
Roberta F. Bonan ◽  
Paulo R. F. Bonan ◽  
André U. D. Batista ◽  
Danyel E. C. Perez ◽  
Lúcio R. C. Castellano ◽  
...  

2011 ◽  
Vol 131 (5) ◽  
pp. 395-400 ◽  
Author(s):  
Toru Oi ◽  
Katsuyoshi Shinyama ◽  
Shigetaka Fujita

Sign in / Sign up

Export Citation Format

Share Document