Biomechanical evaluation of stress distributions at the implant-abutment complex and peri-implant bone around mandibular dental implants with different neck geometries and inclinations

2021 ◽  
pp. 095441192110229
Author(s):  
Murat M Dinc ◽  
Pinar Turkoglu ◽  
Firat Selvi
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Stress Distributions ◽  
Second Molar ◽  
Bone Stress ◽  
Switching Models ◽  
Implant Abutment ◽  
Stress Levels ◽  
Platform Switching ◽  
Simulation And Evaluation

This study aimed to investigate the effects of the different dental implant neck designs, diameters, and inclinations, on the stress distributions at the mandibular crestal bone and implant-abutment complex, using three-dimensional (3D) finite element stress analysis (FEA) method. Finite element models of three-unit fixed partial dentures supported with two same length implants (10 mm), placed on the second premolar and second molar regions, were designed. Eight different models were designed according to the implants’ neck designs (platform switching/traditional), diameters (4.1 mm/4.8 mm) and the tilting angles of the posterior implants (0°/15°). The anterior implants’ widths were 4.1 mm and the neck design of the anterior implants matched the posterior implants. Two types of 100-N loads in vertical and 30° oblique directions were applied separately onto each central fossae and functional cusps of the fixed partial dentures crowns. Algor Fempro Software was used for the simulation and evaluation of the stress levels at the implant-abutment complex and the crestal bone. Stress levels measured at the crestal bone were found to be lower for the platform switching models. However, the platform switching design generated higher stress magnitudes within the implant-abutment complex. Inclined placement of posterior implants increased the amount of stress at the crestal bone around both implants. Biomechanically, selection of the largest diameter possible when using tilted platform switched implants may be recommended at the posterior mandible.

scholarly journals Effect of Microthreads and Platform Switching on Crestal Bone Stress Levels: A Finite Element Analysis

2008 ◽  
Vol 79 (11) ◽  
pp. 2166-2172 ◽  
Author(s):  
Jason Schrotenboer ◽  
Yi-Pin Tsao ◽  
Vipul Kinariwala ◽  
Hom-Lay Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Element Analysis ◽  
Bone Stress ◽  
Stress Levels ◽  
Platform Switching

Influence of Fine Threads and Platform-Switching on Crestal Bone Stress Around Implant—A Three-Dimensional Finite Element Analysis

2013 ◽  
Vol 39 (6) ◽  
pp. 697-703 ◽  
Author(s):  
Pardeep Khurana ◽  
Arun Sharma ◽  
Kiranmeet Kaur Sodhi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Analysis ◽  
Vertical Loading ◽  
Bone Stress ◽  
Oblique Loading ◽  
Dimensional Finite Element ◽  
Platform Switching ◽  
Three Dimensional Finite Element

The aims of this study were to investigate the effect of implant fine threads on crestal bone stress compared to a standard smooth implant collar and to analyze how different abutment diameters influenced the crestal bone stress level. Three-dimensional finite element imaging was used to create a cross-sectional model in SolidWorks 2007 software of an implant (5-mm platform and 10 mm in length) placed in the premolar region of the mandible. The implant model was created to resemble a commercially available fine thread implant. Abutments of different diameters (5.0 mm: standard, 4.5 mm, 4.0 mm, and 3.5 mm) were loaded with a force of 100 N at 90° vertical and 40° oblique angles. Finite element analysis was done in COSMOSWorks software, which was used to analyze the stress patterns in bone, especially in the crestal region. Upon loading, the fine thread implant model had greater stress at the crestal bone adjacent to the implant than the smooth neck implant in both vertical and oblique loading. When the abutment diameter decreased progressively from 5.0 mm to 4.5 mm to 4 mm and to 3.5 mm the thread model showed a reduction of stress at the crestal bone level from 23.2 MPa to 15.02 MPa for fine thread and from 22.7 to 13.5 MPa for smooth collar implant group after vertical loading and from 43.7 MPa to 33.1 MPa in fine thread model and from 36.9 to 20.5 MPa in smooth collar implant model after oblique loading. Fine threads increase crestal stress upon loading. Reduced abutment diameter that is platform switching resulted in less stress translated to the crestal bone in the fine thread and smooth neck.

Comparison of Conventional and Pontic Fixed Partial Dentures Over Implants Using the Finite Element Method: Three-Dimensional Analysis of Cortical and Medullary Bone Stress

2020 ◽  
Vol 46 (3) ◽  
pp. 175-181
Author(s):  
Marcelo Bighetti Toniollo ◽  
Mikaelly dos Santos Sá ◽  
Fernanda Pereira Silva ◽  
Giselle Rodrigues Reis ◽  
Ana Paula Macedo ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Medullary Bone ◽  
Principal Stresses ◽  
Bone Stress ◽  
Bone Damage ◽  
Rehabilitation System ◽  
Minimum Requirements

Rehabilitation with implant prostheses in posterior areas requires the maximum number of possible implants due to the greater masticatory load of the region. However, the necessary minimum requirements are not always present in full. This project analyzed the minimum principal stresses (TMiP, representative of the compressive stress) to the friable structures, specifically the vestibular face of the cortical bone and the vestibular and internal/lingual face of the medullary bone. The experimental groups were as follows: the regular splinted group (GR), with a conventional infrastructure on 3 regular-length Morse taper implants (4 × 11 mm); and the regular pontic group (GP), with a pontic infrastructure on 2 regular-length Morse taper implants (4 × 11 mm). The results showed that the TMiP of the cortical and medullary bones were greater for the GP in regions surrounding the implants (especially in the cervical and apical areas of the same region) but they did not reach bone damage levels, at least under the loads applied in this study. It was concluded that greater stress observed in the GP demonstrates greater fragility with this modality of rehabilitation; this should draw the professional's attention to possible biomechanical implications. Whenever possible, professionals should give preference to use of a greater number of implants in the rehabilitation system, with a focus on preserving the supporting tissue with the generation of less intense stresses.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Finite Element Analysis of Poor Distal Contact of the Femoral Component of a Cementless Hip Endoprosthesis

1993 ◽  
Vol 207 (4) ◽  
pp. 255-261 ◽  
Author(s):  
M Taylor ◽  
E W Abel
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Influencing Factor ◽  
Three Dimensional ◽  
Stress Distributions ◽  
Element Analysis ◽  
Hip Endoprosthesis ◽  
Applied Loading ◽  
Femoral Geometry ◽  
Contact Models

The difficulty of achieving good distal contact between a cementless hip endoprosthesis and the femur is well established. This finite element study investigates the effect on the stress distribution within the femur due to varying lengths of distal gap. Three-dimensional anatomical models of two different sized femurs were generated, based upon computer tomograph scans of two cadaveric specimens. A further six models were derived from each original model, with distal gaps varying from 10 to 60 mm in length. The resulting stress distributions within these were compared to the uniform contact models. The extent to which femoral geometry was an influencing factor on the stress distribution within the bone was also studied. Lack of distal contact with the prosthesis was found not to affect the proximal stress distribution within the femur, for distal gap lengths of up to 60 mm. In the region of no distal contact, the stress within the femur was at normal physiological levels associated with the applied loading and boundary conditions. The femoral geometry was found to have little influence on the stress distribution within the cortical bone. Although localized variations were noted, both femurs exhibited the same general stress distribution pattern.

Sign in / Sign up

Export Citation Format

Share Document