Principle and structure of a multi-chamber piezoelectric pump with large flow rate integrated into printed circuit board

2022 ◽  
pp. 1045389X2110721
Author(s):  
Yun-Hao Peng ◽  
Dai-Hua Wang ◽  
Lian-Kai Tang
Keyword(s):  
Flow Rate ◽  
Compression Ratio ◽  
Layer Structure ◽  
Experimental Results ◽  
Processing Technology ◽  
Rate Model ◽  
Piezoelectric Pump ◽  
Central Deflection ◽  
Maximum Value ◽  
Large Flow

Parametric simulation of multi-chamber piezoelectric pump proposed by authors shows that its flow rate is positively correlated with chamber compression ratio when height of chamber wall is not less than central deflection of circular piezoelectric unimorph actuator (CPUA). Therefore, in this paper, principle and structure of multi-chamber piezoelectric pump with novel CPUAs with three-layer structure are proposed and realized, so as to improve its chamber compression ratio, and then improve its flow rate. Its processing technology compatible with PCB processing technology is studied and its flow rate model is established. Central deflection of CPUA with three-layer structure and the flow rate characteristics are tested. Experimental results show that when the central deflection of CPUA with three-layer structure reaches the maximum value of 106.8 μm, the chamber compression ratio and flow rate of multi-chamber piezoelectric pump reach the maximum value of 50% and 3.11 mL/min, respectively. The maximum flow rate is increased by 622% compared to unimproved pump. By comparing experimental results with numerical and finite element simulation results, the realized multi-chamber piezoelectric pump has large flow rate and the established flow rate model can predict its flow rate.

scholarly journals Equivalent Circuit Modeling for a Valveless Piezoelectric Pump

Sensors ◽  
2018 ◽  
Vol 18 (9) ◽  
pp. 2881 ◽  
Author(s):  
Jianhui Zhang ◽  
Yuan Wang ◽  
Jun Huang
Keyword(s):  
Equivalent Circuit ◽  
Flow Rate ◽  
Equivalent Circuit Model ◽  
Circuit Model ◽  
Experimental Results ◽  
Driving Voltage ◽  
Piezoelectric Pump ◽  
Pump System ◽  
Field Problem ◽  
Valveless Piezoelectric Pump

Various kinds of the models had been proposed to explain the relationship between the performance and the structural parameters of valveless piezoelectric pumps, so as to evaluate the functional performance such devices. Among the models, the equivalent circuit model, which converts the multi-field problem of a valveless piezoelectric pump system into a simple circuit problem, is the most simple and clear one. Therefore, the proposed structure and working principle of the valveless piezoelectric pump with multistage Y-shape treelike bifurcate tubes are analyzed; then, the equivalent circuit model of the valveless piezoelectric pump is established based on the working principles of this pump and liquid-electric analogy theory. Finally, an experimental study of the pump is carried out, with a comparative analysis of the experimental results and the simulation results of the generated equivalent circuit. The experimental results show that with a driving voltage of 100 V and frequency of 6 Hz, the maximum flow rate of the valveless piezoelectric pump is 1.16 mL/min. Meanwhile, the output current of equivalent circuit also reaches its peak at the frequency of 6 Hz, therefore, indicating a good predictive ability of this model in calculating the maximum output flow rate and best working frequency of valveless piezoelectric pumps.

Transient Characteristics of a Centrifugal Pump at Rapid Startup

2019 ◽  
Author(s):  
Teiichi Tanaka ◽  
Michiya Tabaru
Keyword(s):  
Flow Field ◽  
Centrifugal Pump ◽  
Flow Rate ◽  
Thrust Force ◽  
Experimental Results ◽  
Operating Point ◽  
Axial Thrust ◽  
Transient Characteristics ◽  
Transient Period ◽  
Large Flow

Abstract Experimental and CFD studies were carried out on transient behavior of a centrifugal pump at rapid startup. Relationship between the transient characteristics and a flow field in the centrifugal pump was investigated during transient period of the centrifugal pump from experimental results. A single-stage, volute type centrifugal pump is used for the experiments. The pump is equipped with transparent impeller, casing, suction pipe and discharge pipe for PIV in the future. The test setup is a closed-loop and consists of a suction tank, a test pump, an ultrasonic flow meter and a flow control valve. Instantaneous pressure and flow rate were measured at suction and discharge ports with rotational speed during the transient period. The pump suction and delivery pressures were measured using strain gauge type pressure transducers. Unsteady flow rate was calculated from pressure difference between two pressure measurement points in straight pipe of the pump suction lines using the difference of inertia force. The three-dimensional incompressible flow calculation of the test pump is performed using ANSYS® CFX 17.1. The CFD domain is consisted of a pump suction pipe, a pump casing, an impeller and a pump delivery pipe. For all computations, a block structure mesh of around 1,550,000 elements has been used. The mesh is created with the mesh generator ANSYS® ICEM CFD Ver.17.1. Frozen Rotor Method is used for the steady state calculation, and Transient Rotor Method is used for the unsteady calculation. The standard SST model is used for turbulence modelling. Boundary conditions of the pump inlet and outlet are used the time history of total head and mass flow rate obtained from experiment result, respectively. The variation of pump operating point, torque and axial thrust force during transient period were related to the time-dependent flow field, which was investigated using CFD, in the pump. As results of the present study, it was shown that the pump operating point in experiment were larger than quasi-steady one at early transient stage, and then the pump operating point reaches to quasi-steady one. CFD results indicated similar tendency to experimental results on the variation of the pump operating point. Moreover, variation of the torque and axial thrust force during transient period also indicated deviation from each quasi-steady change. From the experimental and CFD results, the deviation of pump operating point, torque and axial thrust force from the quasi-steady change during pump startup period occurs at a large flow rate acceleration. The reason is thought to be due to that the flow field at large flow rate change cannot develop compared with that at the quasi-steady change.

Improved Aero/Hydro Flow-Rate Model Using Acoustics

2018 ◽  
Vol 59 (4) ◽  
pp. 429-438
Author(s):  
Muralidhar Seshadri ◽  
◽  
Jonathan B. Freund ◽  
Pranab N. Jha ◽  
Atchyuta Ramayya Venna ◽  
...  
Keyword(s):  
Flow Rate ◽  
Rate Model

scholarly journals Research on a Piezoelectric Pump with Flexible Valves

2021 ◽  
Vol 11 (7) ◽  
pp. 2909
Author(s):  
Weiqing Huang ◽  
Liyi Lai ◽  
Zhenlin Chen ◽  
Xiaosheng Chen ◽  
Zhi Huang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Fluid Transport ◽  
Smooth Transition ◽  
Driving Voltage ◽  
Piezoelectric Pump ◽  
Venous Valve ◽  
Output Pressure ◽  
Small Flow ◽  
Working Principle ◽  
Opening And Closing

Imitating the structure of the venous valve and its characteristics of passive opening and closing with changes in heart pressure, a piezoelectric pump with flexible valves (PPFV) was designed. Firstly, the structure and the working principle of the PPFV were introduced. Then, the flexible valve, the main functional component of the pump, was analyzed theoretically. Finally, an experimental prototype was manufactured and its performance was tested. The research proves that the PPFV can achieve a smooth transition between valved and valveless by only changing the driving signal of the piezoelectric (PZT) vibrator. The results demonstrate that when the driving voltage is 100 V and the frequency is 25 Hz, the experimental flow rate of the PPFV is about 119.61 mL/min, and the output pressure is about 6.16 kPa. This kind of pump can realize the reciprocal conversion of a large flow rate, high output pressure, and a small flow rate, low output pressure under the electronic control signal. Therefore, it can be utilized for fluid transport and pressure transmission at both the macro-level and the micro-level, which belongs to the macro–micro combined component.

scholarly journals Thermal Efficiency and Economics of a Boil-Off Hydrogen Re-Liquefaction System Considering the Energy Efficiency Design Index for Liquid Hydrogen Carriers

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4566
Author(s):  
Minsoo Choi ◽  
Wongwan Jung ◽  
Sanghyuk Lee ◽  
Taehwan Joung ◽  
Daejun Chang
Keyword(s):  
Flow Rate ◽  
Life Cycle Cost ◽  
Specific Energy Consumption ◽  
Liquid Hydrogen ◽  
Efficient Design ◽  
Fuel Cell Stack ◽  
Energy Efficiency Design Index ◽  
The Cost ◽  
Large Flow

This study analyzes the thermodynamic, economic, and regulatory aspects of boil-off hydrogen (BOH) in liquid hydrogen (LH2) carriers that can be re-liquefied using a proposed re-liquefaction system or used as fuel in a fuel cell stack. Five LH2 carriers sailing between two designated ports are considered in a case study. The specific energy consumption of the proposed re-liquefaction system varies from 8.22 to 10.80 kWh/kg as the re-liquefaction-to-generation fraction (R/G fraction) is varied. The economic evaluation results show that the cost of re-liquefaction decreases as the re-liquefied flow rate increases and converges to 1.5 $/kg at an adequately large flow rate. Three energy efficient design index (EEDI) candidates are proposed to determine feasible R/G fractions: an EEDI equivalent to that of LNG carriers, an EEDI that considers the energy density of LH2, and no EEDI restrictions. The first EEDI candidate is so strict that the majority of the BOH should be used as fuel. In the case of the second EEDI candidate, the permittable R/G fraction is between 25% and 33%. If the EEDI is not applied for LH2 carriers, as in the third candidate, the specific life-cycle cost decreases to 67% compared with the first EEDI regulation.

Experiment analysis of high output pressure piezoelectric pump with straight arm wheeled check valve

2021 ◽  
pp. 1045389X2098700
Author(s):  
Lipeng He ◽  
Xiaoqiang Wu ◽  
Zheng Zhang ◽  
Zhe Wang ◽  
Bangcheng Zhang ◽  
...  
Keyword(s):  
Chemical Analysis ◽  
Energy Loss ◽  
Check Valve ◽  
Experimental Results ◽  
Piezoelectric Pump ◽  
Output Pressure ◽  
Pressure Characteristic ◽  
Analysis System ◽  
Experiment Analysis ◽  
High Output

Piezoelectric pumps are applied in many fields, such as chemical analysis system and fluid pumping systems. Piezoelectric pumps with high output pressure can meet the needs of more fields. This article introduces the design and fabrication of a high output pressure piezoelectric pump with straight arm wheeled check valve. In this paper, the influence of straight arm wheeled check valve on the output pressure of piezoelectric pump is deeply discussed from the aspect of energy loss. This study investigated the effect of valve arm number ( N = 2, 3,4, and 5), the valve arm width ( W = 0.8, 1.0, and 1.2 mm), and the valve arm length ( L = 1.92, 2.02, and 2.12 mm) on the output pressure of piezoelectric pump. The output pressure characteristic of straight arm wheeled check valve piezoelectric pump with different valve parameters is obtained by experiment. Experimental results show that when N = 4, W = 1.0 mm, L = 2.02 mm, the output pressure of the straight arm wheeled check valve piezoelectric pump has the best output pressure of 27.41 kPa at 220 V and 85 Hz. This study provides a reference for the further application of piezoelectric pumps in fluid pumping field.

scholarly journals Improving Output Performance of a Resonant Piezoelectric Pump by Adding Proof Masses to a U-Shaped Piezoelectric Resonator

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 500
Author(s):  
Jian Chen ◽  
Wenzhi Gao ◽  
Changhai Liu ◽  
Liangguo He ◽  
Yishan Zeng
Keyword(s):  
Flow Rate ◽  
Maximum Flow ◽  
Working Fluid ◽  
Driving Voltage ◽  
Piezoelectric Resonator ◽  
Piezoelectric Pump ◽  
Compact Structure ◽  
Output Performance ◽  
Volume Efficiency ◽  
Working Efficiency

This study proposes the improvement of the output performance of a resonant piezoelectric pump by adding proof masses to the free ends of the prongs of a U-shaped piezoelectric resonator. Simulation analyses show that the out-of-phase resonant frequency of the developed resonator can be tuned more efficiently within a more compact structure to the optimal operating frequency of the check valves by adjusting the thickness of the proof masses, which ensures that both the resonator and the check valves can operate at the best condition in a piezoelectric pump. A separable prototype piezoelectric pump composed of the proposed resonator and two diaphragm pumps was designed and fabricated with outline dimensions of 30 mm × 37 mm × 54 mm. Experimental results demonstrate remarkable improvements in the output performance and working efficiency of the piezoelectric pump. With the working fluid of liquid water and under a sinusoidal driving voltage of 298.5 Vpp, the miniature pump can achieve the maximum flow rate of 2258.9 mL/min with the highest volume efficiency of 77.1% and power consumption of 2.12 W under zero backpressure at 311/312 Hz, and the highest backpressure of 157.3 kPa under zero flow rate at 383 Hz.

A Technique for the Laboratory Determination of Recirculation in Single Needle Dialysis

1993 ◽  
Vol 16 (2) ◽  
pp. 63-70 ◽  
Author(s):  
N.A. Hoenich ◽  
P.T. Smirthwaite ◽  
C. Woffindin ◽  
P. Lancaster ◽  
T.H. Frost ◽  
...  
Keyword(s):  
Experimental Data ◽  
Flow Rate ◽  
Experimental Results ◽  
New Technique ◽  
Treatment Efficiency ◽  
Single Lumen ◽  
Theoretical Predictions ◽  
Lumen Catheter ◽  
A New Technique

Recirculation is an important factor in single needle dialysis and, if high, can compromise treatment efficiency. To provide information regarding recirculation characteristics of access devices used in single needle dialysis, we have developed a new technique to characterise recirculation and have used this to measure the recirculation of a Terumo 15G fistula needle and a VasCath SC2300 single lumen catheter. The experimentally obtained results agreed well with those established clinically (8.5 ± 2.4% and 18.4 ± 3.4%). The experimental results have also demonstrated a dependence on access type, pump speeds and fistula flow rate. A comparison of experimental data with theoretical predictions showed that the latter exceeded those measured with the largest contribution being due to the experimental fistula.

Evaporation and Viscous Flow in Triangular Grooves in Micro Heat Pipes

2005 ◽  
Author(s):  
Mulugeta Markos ◽  
Vladimir S. Ajaev ◽  
G. M. Homsy
Keyword(s):  
Cross Section ◽  
Flow Rate ◽  
Cross Sections ◽  
Wedge Angle ◽  
Heat Pipes ◽  
Type Model ◽  
Pressure Gradients ◽  
Maximum Value ◽  
Dry Out ◽  
Micro Heat Pipes

We develop a lubrication type model of a liquid flow in a wedge in the limit of small capillary numbers and negligible gravity. The model incorporates the effects of capillary pressure gradients and evaporation. Steady vapor-liquid interface shapes are found for a range of parameters. In the limit of weak evaporation the flow is the same in all cross-sections and can be controlled by changing the wedge angle. We find the wedge angle that results in the maximum value of the flow rate for a given contact angle. For high evaporation rates, both the flow rate and the amount of liquid in each cross-section along the wedge decrease until the point of dry-out is reached. The location of the dry-out point is studied as a function of evaporation. Practical suggestions about optimization of micro heat pipes are given.

Optimization of Inlet Ring Groove Arrangement for Suppression of Unstable Flow in a Centrifugal Impeller

2005 ◽  
Author(s):  
Masahiro Ishida ◽  
Daisaku Sakaguchi ◽  
Hironobu Ueki
Keyword(s):  
Flow Rate ◽  
The Other ◽  
Centrifugal Impeller ◽  
Shape Parameters ◽  
Unstable Flow ◽  
Ring Groove ◽  
Flow Rates ◽  
Small Flow ◽  
Specific Speed ◽  
Large Flow

An optimization of the inlet ring groove arrangement has been pursued in the present study for obtaining better impeller characteristics and a wider operation range at both small and large flow rates in a high specific speed type centrifugal impeller with inducer. The effects of the shape parameters with respect to the inlet ring groove on the impeller characteristic and the flow incidence were analyzed mainly based on numerical simulations, but also compared to the experimental results. At small flow rates, a significant improvement in the impeller characteristic is achieved due to reduction in the excessive-positive flow incidence by optimizing both location and width of the rear groove near the inducer tip throat. On the other hand, the impeller characteristic is improved at large flow rates by implementing the corner radius at the rear groove edge and by placing another front ring groove in the suction pipe. As a result, by the optimized configuration of the front and rear ring grooves, the unstable flow range of the test impeller can be reduced by about 50% without deterioration of the impeller characteristic even at the 125% flow rate.

Sign in / Sign up

Export Citation Format

Share Document