Modeling two-phase fluid flow and rock deformation in fractured porous media

Poromechanics ◽  
2020 ◽  
pp. 333-338
Author(s):  
M. Bai ◽  
F. Meng ◽  
J.-C. Roegiers ◽  
Y. Abousleiman
Keyword(s):  
Porous Media ◽  
Fluid Flow ◽  
Fractured Porous Media ◽  
Rock Deformation ◽  
Two Phase ◽  
Phase Fluid

Development of a Numerical Model for Single- and Two-Phase Flow Simulation in Perforated Porous Media

2019 ◽  
Vol 142 (4) ◽  
Author(s):  
Hamed Movahedi ◽  
Mehrdad Vasheghani Farahani ◽  
Mohsen Masihi
Keyword(s):  
Porous Media ◽  
Fluid Flow ◽  
Transient Flow ◽  
Accurate Determination ◽  
Flow Simulation ◽  
Velocity Profiles ◽  
Geometrical Parameters ◽  
Reservoir Properties ◽  
Two Phase ◽  
Phase Fluid

Abstract In this paper, we present a computational fluid dynamics (CFD) model to perform single- and two-phase fluid flow simulation on two- and three-dimensional perforated porous media with different perforation geometries. The finite volume method (FVM) has been employed to solve the equations governing the fluid flow through the porous media and obtain the pressure and velocity profiles. The volume of fluid (VOF) method has also been utilized for accurate determination of the volume occupied by each phase. The validity of the model has been achieved via comparing the simulation results with the available experimental data in the literature. The model was used to analyze the effect of perforation geometrical parameters (length and diameter), degree of heterogeneity, and also crushed zone properties (permeability and thickness) on the pressure and velocity profiles. The two-phase fluid flow around the perforation tunnel under the transient flow regime was also investigated by considering a constant mass flow boundary condition at the inlet. The developed model successfully predicted the pressure drop and resultant temperature changes for the system of air–water along clean and gravel-filled perforations under the steady-state conditions. The presented model in this study can be used as an efficient tool to design the most appropriate perforation strategy with respect to the well characteristics and reservoir properties.

Fabrication of a Microchannel Device With a Three-Dimensional Pore Network Using a Sacrificial Sugar Template

2020 ◽  
Author(s):  
Haipeng Zhang ◽  
Tomer Palmon ◽  
Seunghee Kim ◽  
Sangjin Ryu
Keyword(s):  
Porous Media ◽  
Fluid Flow ◽  
Pore Structure ◽  
Three Dimensional ◽  
Pore Network ◽  
Compressed Air ◽  
Microfluidic Channels ◽  
Two Phase ◽  
Flow Through ◽  
Phase Fluid

Abstract Porous media compressed air energy storage (PM-CAES) is an emerging technology that stores compressed air in an underground aquifer during the off-peak periods, to mitigate the mismatch between energy supplies and demands. Thus, PM-CAES involves repeated two-phase fluid flow in porous media, and ensuring the success of PM-CAES requires a better understanding of repetitive two-phase fluid flow through porous media. For this purpose, we previously developed microfluidic channels that retain a two-dimensional (2D) pore network. Because it was found that the geometry of the pore structure significantly affects the patterns and occupational efficiencies of a non-wetting fluid during the drainage-imbibition cycles, a more realistic microfluidic model is needed to reflect the three-dimensional (3D) nature of pore structures in the underground geologic formation. In this study, we developed an easy-to-adopt method to fabricate a microfluidic device with a 3D random pore network using a sacrificial sugar template. Instead of using a master mold made in photolithography, a sacrificial mold was made using sugar grains so that the mold could be washed away after PDMS curing. First, we made sugar templates with different levels of compaction load, and found that the thickness of the templates decreased as the compaction load increased, which suggests more packing of sugar grains and thus lower porosity in the template. Second, we fabricated PDMS porous media using the sugar template as a mold, and imaged their pore structure using micro computed tomography (micro-CT). Pores within PDSM samples appeared more tightly packed as the compacting force increased. Last, we fabricated a prototype PDMS channel device with a 3D pore network using a sugar template, and visualized flow through the pore network using colored water. The flow visualization result shows that the water was guided by the random pores and that the resultant flow pattern was three dimensional.

scholarly journals Finite element method for modelling of two phase fluid flow in porous media

2018 ◽  
Vol 1123 ◽  
pp. 012002 ◽  
Author(s):  
H Ali ◽  
H Soleimani ◽  
N Yahya ◽  
M K Baig ◽  
A Rostami
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Porous Media ◽  
Fluid Flow ◽  
Flow In Porous Media ◽  
Two Phase ◽  
Phase Fluid ◽  
Element Method

Microfluidic Study on the Two-Phase Fluid Flow in Porous Media During Repetitive Drainage-Imbibition Cycles and Implications to the CAES Operation

2019 ◽  
Vol 131 (2) ◽  
pp. 449-472 ◽  
Author(s):  
Jingtao Zhang ◽  
Haipeng Zhang ◽  
Donghee Lee ◽  
Sangjin Ryu ◽  
Seunghee Kim
Keyword(s):  
Porous Media ◽  
Fluid Flow ◽  
Flow In Porous Media ◽  
Two Phase ◽  
Phase Fluid
Sign in / Sign up

Export Citation Format

Share Document