Effects of different starch types on the physico-mechanical and morphological properties of low density polyethylene composites

2015 ◽  
Vol 35 (8) ◽  
pp. 793-804 ◽  
Author(s):  
Md. Dalour Hossen Beg ◽  
Shaharuddin Bin Kormin ◽  
Mohd Bijarimi ◽  
Haydar U. Zaman
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Water Absorption ◽  
Starch Content ◽  
Flexural Modulus ◽  
Morphological Properties ◽  
Low Density Polyethylene ◽  
Flow Index ◽  
Low Density ◽  
Sago Starch

Abstract The aim of this research is to investigate the effects of different thermoplastic starches and starch contents on the physico-mechanical and morphological properties of new polymeric-based composites from low density polyethylene (LDPE) and thermoplastic starches. Different compositions of thermoplastic starches (5–40 wt%) and LDPE were melt blended by extrusion and injection molding. The resultant materials were characterized with respect to the following parameters, i.e., melt flow index (MFI), mechanical properties (tensile, flexural, stiffness and impact strength) and water absorption. Scanning electron microscopy (SEM) was also used in this study for evaluating blend miscibility. MFI values of all blends decreased as the starch content increased, while the sago starch formulation showed a higher MFI value than others. The incorporation of fillers into LDPE matrix resulted in an increased in tensile modulus, flexural strength, flexural modulus and slightly decreased tensile strength and impact strength. However, sago starch filled composites exhibited better mechanical properties as compared to other starches. The SEM results revealed that the miscibility of such blends is dependent on the type of starch used. The water absorption increased with immersion time and the thermoplastic sago starch samples showed the lowest percentage of water absorption compared with other thermoplastic starches.

scholarly journals Low-Temperature Mechanical Properties of High-Density and Low-Density Polyethylene and Their Blends

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1821
Author(s):  
Ildar I. Salakhov ◽  
Nadim M. Shaidullin ◽  
Anatoly E. Chalykh ◽  
Mikhail A. Matsko ◽  
Alexey V. Shapagin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Impact Strength ◽  
Relative Elongation ◽  
High Density ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Elongation At Break ◽  
Subzero Temperatures ◽  
Izod Impact

Low-temperature properties of high-density polyethylene (HDPE), low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE), and their blends were studied. The analyzed low-temperature mechanical properties involve the deformation resistance and impact strength characteristics. HDPE is a bimodal ethylene/1-hexene copolymer; LDPE is a branched ethylene homopolymer containing short-chain branches of different length; LLDPE is a binary ethylene/1-butene copolymer and an ethylene/1-butene/1-hexene terpolymer. The samples of copolymers and their blends were studied by gel permeation chromatography (GPC), differential scanning calorimetry (DSC), 13С NMR spectroscopy, and dynamic mechanical analysis (DMA) using testing machines equipped with a cryochamber. It is proposed that such parameters as “relative elongation at break at −45 °C” and “Izod impact strength at −40 °C” are used instead of the ductile-to-brittle transition temperature to assess frost resistance properties because these parameters are more sensitive to deformation and impact at subzero temperatures for HDPE. LLDPE is shown to exhibit higher relative elongation at break at −45 °C and Izod impact strength at −20 ÷ 60 °C compared to those of LDPE. LLDPE terpolymer added to HDPE (at a content ≥ 25 wt.%) simultaneously increases flow properties and improves tensile properties of the blend at −45 °C. Changes in low-temperature properties as a function of molecular weight, MWD, crystallinity, and branch content were determined for HDPE, LLDPE, and their blends. The DMA data prove the resulting dependences. The reported findings allow one to understand and predict mechanical properties in the HDPE–LLDPE systems at subzero temperatures.

Cable and Wire Application: Adoption of Nanomagnesium Hydroxide Blended with LDPE/EVA for Mechanical and Physical Properties

2013 ◽  
Vol 701 ◽  
pp. 202-206
Author(s):  
Ahmad Aroziki Abdul Aziz ◽  
Sakinah Mohd Alauddin ◽  
Ruzitah Mohd Salleh ◽  
Mohammed Iqbal Shueb
Keyword(s):  
Mechanical Properties ◽  
Physical Properties ◽  
Melt Flow Index ◽  
Low Density Polyethylene ◽  
Flow Index ◽  
Low Density ◽  
Elongation At Break ◽  
Mechanical And Physical Properties ◽  
Poly Ethylene ◽  
Loading Amount

Effect of nanoMagnesium Hydroxide (MH) nloading amount to the mechanical and physical properties of Low Density Polyethylene (LDPE)/ Poly (ethylene-co vinyl acetate)(EVA) nanocomposite has been described and investigated in this paper. The tensile strength results show that increased amount of nanofiller will decrease and deteriorate the mechanical properties. The elongation at break decreased continuously with increasing loading of nanofiller. Generally, mechanical properties become poorer as loading amount increase. Melt Flow Index values for physical properties also provide same trend as mechanical properties results. Increase filler amount reduced MFI values whereby increased resistance to the flow.

Effects of microcrystalline cellulose on the mechanical properties of low-density polyethylene composites

2018 ◽  
Vol 32 (3) ◽  
pp. 297-311 ◽  
Author(s):  
Yousef Ahmad Mubarak ◽  
Raghda Talal Abdulsamad
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Impact Strength ◽  
Tensile Properties ◽  
Microcrystalline Cellulose ◽  
Weight Fraction ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Ldpe Composites ◽  
The Impact

This work was intended to provide an understanding of the effect of microcrystalline cellulose (MCC) on the mechanical properties of low-density polyethylene (LDPE). The impact resistance and the tensile properties of low-density LDPE/MCC composites were investigated. The weight fraction of MCC was varied at (0, 0.5, 1, 2.5, 5, 10, 20, and 30 wt%). The obtained blends were then used to prepare the required tensile and impact testing samples by hot compression molding technique. It has been found that MCC has a strong influence on the mechanical properties of LDPE. At a low MCC weight fraction, there was a little improvement in the ultimate strength, fracture stress, and elongation at break, but at a high MCC weight fraction, the tensile properties were deteriorated and reduced significantly. The addition of 1 wt% MCC to LDPE enhanced the mentioned properties by 10, 25, and 6%, respectively. While at 30 wt% MCC, these properties were lowered by 36, 25, and 96%. The elastic modulus of LDPE composites was improved on all MCC weight fractions used in the study, at 20 wt% MCC, an increase in the elastic modulus by 12 folds was achieved. On the other hand and compared with the impact strength of pure LDPE, the addition of MCC particles enhanced the impact strength, the highest value obtained was for LDPE composites filled with 10 wt% MCC where the impact strength enhanced by two folds.

Low Density Polyethylene (LDPE)/Thermoplastic Sago Starch (TPSS) Blend Filled with Kenaf Core Fiber (KCF)

2012 ◽  
Vol 626 ◽  
pp. 1048-1053
Author(s):  
Norshahida Sarifuddin ◽  
Hanafi Ismail ◽  
Ahmad Zuraida
Keyword(s):  
Starch Content ◽  
Experimental Result ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Sago Starch ◽  
Elongation At Break ◽  
Kenaf Core ◽  
Blending Method ◽  
Core Fiber ◽  
Hydrocarbon Polymer

Recently, blending of common hydrocarbon polymer with natural based materials has gain much interest towards the development of degradable composite. In this study, a series of low density polyethylene (LDPE)/thermoplastic sago starch (TPSS) blend reinforced with kenaf core fiber (KCF) with starch content ranging from 10 to 40 % were prepared via melt-blending method. For this study, kenaf loading was fixed at 20 % (by weight). The blended samples were characterized by means of tensile test and morphological study. The experimental result shows that there is a gradual decrease in tensile strength, modulus and elongation at break with increase in starch loading. The scanning electron micrograph (SEM) supports the findings of tensile properties.

scholarly journals Fabrication of raw and oxidized saw dust reinforced low density polyethylene (LDPE) composites and investigation of their physico-mechanical properties

2013 ◽  
Vol 47 (4) ◽  
pp. 365-372 ◽  
Author(s):  
S Sultana ◽  
HP Nur ◽  
T Saha ◽  
M Saha
Keyword(s):  
Mechanical Properties ◽  
Mangifera Indica ◽  
Flexural Modulus ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Electron Micrograph ◽  
Scanning Electron Micrograph ◽  
Saw Dust ◽  
Ldpe Composites ◽  
Scanning Electron

In this research work, cellulosic waste mango (Mangifera indica) saw dust used as the reinforcing material with low density polyethylene (LDPE). A number of samples of saw dust reinforced low density polyethylene (LDPE) composites were prepared by compression moulding technique. In order to improve the mechanical properties of saw dust-LDPE composites, unbleached raw saw dust fibers were modified by oxidation using sodium hypochlorite. FT-IR spectroscopic and scanning electron micrograph (SEM) analyses were done and the results showed the evidence of positive oxidation reaction. The effects of oxidized saw dust on the performance of oxidized saw dust reinforced LDPE composites were studied comparing with the raw saw dust-LDPE composites. The effects of fiber content on the physico-mechanical properties of composites were also studied by preparing the composites with different percentage of fiber loading (from 7.5 wt% to 30 wt%) for each type of composite. Mechanical properties such as tensile strength, tensile modulus, elongation at break, flexural strength, flexural modulus of the resulting composite were measured. Better results were obtained from oxidized saw dust-LDPE composites. Scanning electron micrograph and water absorption tests were carried out for all composites and improved results were found for oxidized saw dust-LDPE composites. Bangladesh J. Sci. Ind. Res. 47(4), 365-372, 2012 DOI: http://dx.doi.org/10.3329/bjsir.v47i4.14065

scholarly journals Hybrid Cellulose-Glass Fiber Composites for Automotive Applications

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3189 ◽  
Author(s):  
Annandarajah ◽  
Langhorst ◽  
Kiziltas ◽  
Grewell ◽  
Mielewski ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Fiber Composite ◽  
Glass Fibers ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
Polyamide 6 ◽  
Morphological Properties ◽  
Hybrid Fibers ◽  
Glass Fiber Composites

: In the recent years, automakers have been striving to improve the carbon footprint of their vehicles. Sustainable composites, consisting of natural fibers, and/or recycled polymers have been developed as a way to increase the “green content” and reduce the weight of a vehicle. In addition, recent studies have found that the introduction of synthetic fibers to a traditional fiber composite such as glass filled plastics, producing a composite with multiple fillers (hybrid fibers), can result in superior mechanical properties. The objective of this work was to investigate the effect of hybrid fibers on characterization and material properties of polyamide-6 (PA6)/polypropylene (PP) blends. Cellulose and glass fibers were used as fillers and the mechanical, water absorption, and morphological properties of composites were evaluated. The addition of hybrid fibers increased the stiffness (tensile and flexural modulus) of the composites. Glass fibers reduced composite water absorption while the addition of cellulose fibers resulted in higher composite stiffness. The mechanical properties of glass and cellulose filled PA6/PP composites were optimized at loading levels of 15 wt% glass and 10 wt% cellulose, respectively.

Study on the Crystallinity and Mechanical Properties of PC/PLA/LLDPE/ Montmorillonite Blends

2013 ◽  
Vol 739 ◽  
pp. 38-41
Author(s):  
Yi Chen ◽  
Yue Peng ◽  
Wen Yong Liu ◽  
Guang Sheng Zeng ◽  
Xiang Gang Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Impact Strength ◽  
High Performance ◽  
Impact Resistance ◽  
Low Density Polyethylene ◽  
Poly Lactic Acid ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Elongation At Break

Polycarbonate/poly (lactic acid)/(PC/PLA) blend is a kind of novel potential material for introducing the degradability of PLA to high performance PC. However, the bad compatibility between PC and PLA results in poor impact resistance and strength, which limits its applications. For resolving the problem, linear low density polyethylene (LLDPE) was added into blend to improve the mechanical properties, especially the toughness. Meantime, nanosized montmorillonite was also used as an additive for modifying the blend. The results showed that the the tensile and impact strength, the elongation at break of PC/PLA all be improved with the increase of LLDPE, the nanosized montmorillonite could also increase the strength of blends when the content is lower than wt5% of blends.

Sign in / Sign up

Export Citation Format

Share Document