The Role of Vacancies and Interstitials in Transient Enhanced Diffusion of Arsenic Implanted into Silicon

1997 ◽  
Vol 469 ◽  
Author(s):  
D. Venables ◽  
V. Krishnamoorthy ◽  
H.- J. Gossmann ◽  
A. Lilak ◽  
K. S. Jones ◽  
...  
Keyword(s):  
Fermi Level ◽  
Point Defect ◽  
Boron Diffusion ◽  
Direct Role ◽  
Enhanced Diffusion ◽  
Projected Range ◽  
Transient Enhanced Diffusion ◽  
Diffusion Enhancement ◽  
Recombination Centers

ABSTRACTBoron and antimony doped superlattices (DSLs) were implanted with arsenic at 40 keV to doses of 2×1014 cm−2, 5×1015 cm−2 and 2×1016 cm−2. Increasing the arsenic dose above 5×1015 cm−2 resulted in a reduction in the extent of arsenic transient enhanced diffusion (TED) following annealing at 700°C, 16 hr. Concurrent with this reduction in TED was a reduction in the number of free interstitials beyond the end-of-range, as measured by the boron diffusion enhancement in the doped superlattices. No enhancement in antimony diffusivity was observed in this region, indicating that vacancies play no direct role in the diffusion of arsenic in this region, although an indirect role for vacancies as recombination centers for mobile interstitials is not precluded by these experiments. We conclude that interstitials dominate arsenic diffusion in the end-of-range region and beyond. Interpretation of the DSL data in the projected range region is complicated by Fermi level and segregation effects and no definitive conclusion can be reached about the point defect populations in this region.

Investigation of Fluorine Effect on the Boron Diffusion by Mean of Boron Redistribution in Shallow Delta-doped Layers

2004 ◽  
Vol 810 ◽  
Author(s):  
A. Halimaoui ◽  
J. M. Hartmann ◽  
C. Laviron ◽  
R. El-Farhane ◽  
F. Laugier
Keyword(s):  
Point Defects ◽  
Depth Profiling ◽  
Boron Diffusion ◽  
Enhanced Diffusion ◽  
Boron Doped ◽  
Transient Enhanced Diffusion ◽  
Sims Depth Profiling

ABSTRACTPreviously published articles have shown that co-implanted fluorine reduces transient enhanced diffusion of boron. However, it is not yet elucidated whether this effect is due to interaction of fluorine with point-defects or boron atoms. In this work, we have used boron redistribution in a shallow Delta-doped Si structures in order to get some insights into the role of fluorine in the boron diffusion. The structures consisted of 3 boron-doped layers separated by 40nm-thick undoped silicon. The samples were given to Ge preamorphization and F co-implant. SIMS depth profiling was used to analyse boron redistribution after annealing. The results we obtained strongly suggest that fluorine is not interacting with point-defects. The reduction in boron TED is most probably due to boron-fluorine interaction.

Effects of Interstitial Clustering on Transient Enhanced Diffusion of Boron in Silicon

1996 ◽  
Vol 439 ◽  
Author(s):  
S. Solmi ◽  
S. Valmorri
Keyword(s):  
Diffusion Mechanism ◽  
Boron Diffusion ◽  
Experimental Conditions ◽  
Enhanced Diffusion ◽  
Transient Enhanced Diffusion ◽  
Good Account ◽  
Diffusion Enhancement ◽  
Heavily Doped ◽  
Kinetics Of ◽  
New Phase

AbstractA simulation model for Boron diffusion which takes into account the aggregation of the excess interstitials in clusters, and subsequently, the dissolution of these defects, is proposed. The interstitial supersaturation and generation rate are determined according to the classical theory of nucleation and growth of particles, in analogy with the precipitation of a new phase in heavily doped silicon. The clusters are considered as precipitates formed by interstitial Si atoms. The B diffusion is modelled on the basis of the dopant-interstitial pair diffusion mechanism. The clusters dissolution during annealing maintains nearly constant, for a long period, the interstitial supersaturation and the related enhancement of the boron diffusion. This gives a good account of the diffusion results over a large range of experimental conditions. Furthermore, this approach describes most of the behavior of the transient enhanced diffusion (TED), like the temperature dependence of the level of the B diffusion enhancement, the dependence of the duration of the phenomenon on implanted dose, and the scarce dependence on the damage distribution in depth. The results of the simulations are compared with experimental data on the kinetics of interstitial cluster dissolution and of B TED.

Effects of Interstitial Clustering on Transient Enhanced Diffusion of Boron in Silicon

1996 ◽  
Vol 438 ◽  
Author(s):  
S. Solmi ◽  
S. Valmorri
Keyword(s):  
Diffusion Mechanism ◽  
Boron Diffusion ◽  
Experimental Conditions ◽  
Enhanced Diffusion ◽  
Transient Enhanced Diffusion ◽  
Good Account ◽  
Diffusion Enhancement ◽  
Heavily Doped ◽  
Kinetics Of ◽  
New Phase

AbstractA simulation model for Boron diffusion which takes into account the aggregation of the excess interstitials in clusters, and subsequently, the dissolution of these defects, is proposed. The interstitial supersaturation and generation rate are determined according to the classical theory of nucleation and growth of particles, in analogy with the precipitation of a new phase in heavily doped silicon. The clusters are considered as precipitates formed by interstitial Si atoms. The B diffusion is modelled on the basis of the dopant-interstitial pair diffusion mechanism. The clusters dissolution during annealing maintains nearly constant, for a long period, the interstitial supersaturation and the related enhancement of the boron diffusion. This gives a good account of the diffusion results over a large range of experimental conditions. Furthermore, this approach describes most of the behavior of the transient enhanced diffusion (TED), like the temperature dependence of the level of the B diffusion enhancement, the dependence of the duration of the phenomenon on implanted dose, and the scarce dependence on the damage distribution in depth. The results of the simulations are compared with experimental data on the kinetics of interstitial cluster dissolution and of B TED.

Effect of Energy and Dose on Transient-Enhanced Diffusion and Defect Microstructure in Low Energy High Dose As+ Implanted Si

1996 ◽  
Vol 438 ◽  
Author(s):  
V. Krishnamoorthy ◽  
D. Venables ◽  
K. Moeller ◽  
K. S. Jones ◽  
B. Freer
Keyword(s):  
Point Defects ◽  
Surface Recombination ◽  
High Dose ◽  
Enhanced Diffusion ◽  
Projected Range ◽  
Diffusion Enhancement ◽  
Defect Microstructures ◽  
Dose Dependent ◽  
Higher Doses ◽  
Defect Microstructure

Abstract(001) CZ silicon wafers were implanted with arsenic (As+) at energies of 10–50keV to doses of 2×1014 to 5×1015/cm2. All implants were amorphizing in nature. The samples were annealed at 700°C for 16hrs. The resultant defect microstructures were analyzed by XTEM and PTEM and the As profiles were analyzed by SIMS. The As profiles showed significantly enhanced diffusion in all of the annealed specimens. The diffusion enhancement was both energy and dose dependent. The lowest dose implant/annealed samples did not show As clustering which translated to a lack of defects at the projected range. At higher doses, however, projected range defects were clearly observed, presumably due to interstitials generated during As clustering. The extent of enhancement in diffusion and its relation to the defect microstructure is explained by a combination of factors including surface recombination of point defects, As precipitation, As clustering and end of range damage.

Effect of Nitrogen Implants on Boron Transient Enhanced Diffusion

2000 ◽  
Vol 610 ◽  
Author(s):  
Omer Dokumaci ◽  
Paul Ronsheim ◽  
Suri Hegde ◽  
Dureseti Chidambarrao ◽  
Lahir Shaik-Adam ◽  
...  
Keyword(s):  
Low Temperature ◽  
Boron Diffusion ◽  
High Nitrogen ◽  
Enhanced Diffusion ◽  
Transient Enhanced Diffusion ◽  
High Boron ◽  
Buried Layer ◽  
Higher Doses ◽  
Low Nitrogen ◽  
Temperature Furnace

AbstractThe effect of nitrogen implants on boron transient enhanced diffusion was studied for nitrogen-only, boron-only, and boron plus nitrogen implants. A boron buried layer was used as a detector for interstitial supersaturation in the samples. Boron dose ranged from 1×1014 to 1×1015 cm−2 and N2+ dose from 5×1013 and 5×1014 cm−2. The energies were chosen such that the location of the nitrogen and boron peaks matched. After the implants, RTA and low temperature furnace anneals were carried out. The diffusivity enhancements were extracted from the buried layer profiles by simulation. Nitrogen-only implants were found to cause significant enhanced diffusion on the buried boron layer. For lower doses, the enhancement of the nitrogen implant is about half as that of boron whereas the enhancements are equal at higher doses. Nitrogen coimplant with boron increases the transient enhanced diffusion of boron at low boron doses, which implies that nitrogen does not act as a strong sink for excess interstitials unlike carbon. At high boron doses, nitrogen co-implant does not significantly change boron diffusion. Sheet resistance measurements indicate that low nitrogen doses do not affect the activation of boron whereas high nitrogen doses either reduce the activation of boron or the mobility of the holes.

Effect of Energy and Dose on Transient-Enhanced Diffusion and Defect Microstructure in Low Energy High Dose As+ Implanted Si

1996 ◽  
Vol 439 ◽  
Author(s):  
V. Krishnamoorthy ◽  
D. Venables ◽  
K. Moeller ◽  
K. S. Jones ◽  
B. Freer
Keyword(s):  
Point Defects ◽  
Surface Recombination ◽  
High Dose ◽  
Enhanced Diffusion ◽  
Projected Range ◽  
Diffusion Enhancement ◽  
Defect Microstructures ◽  
Dose Dependent ◽  
Higher Doses ◽  
Defect Microstructure

Abstract(001) CZ silicon wafers were implanted with arsenic (As+) at energies of 10–50keV to doses of 2x 1014 to 5x1015/cm2. All implants were amorphizing in nature. The samples were annealed at 700°C for 16hrs. The resultant defect microstructures were analyzed by XTEM and PTEM and the As profiles were analyzed by SIMS. The As profiles showed significantly enhanced diffusion in all of the annealed specimens. The diffusion enhancement was both energy and dose dependent. The lowest dose implant/annealed samples did not show As clustering which translated to a lack of defects at the projected range. At higher doses, however, projected range defects were clearly observed, presumably due to interstitials generated during As clustering. The extent of enhancement in diffusion and its relation to the defect microstructure is explained by a combination of factors including surface recombination of point defects, As precipitation, As clustering and end of range damage.

The Effect of Fluorine Implantation on Boron Diffusion in Metastable Si0.86 Ge0.14

2004 ◽  
Vol 810 ◽  
Author(s):  
Huda A. W. A. El Mubarek ◽  
Yun Wang ◽  
Janet M. Bonar ◽  
Peter Hemment ◽  
Peter Ashburn
Keyword(s):  
Thermal Diffusion ◽  
Sige Layer ◽  
Dislocation Loops ◽  
Boron Diffusion ◽  
Rich Region ◽  
Implantation Energy ◽  
Enhanced Diffusion ◽  
Partial Relaxation ◽  
Transient Enhanced Diffusion ◽  
Marker Layer

ABSTRACTThis paper investigates the effect of varying F+ implantation energy on boron thermal diffusion and boron transient enhanced diffusion (TED) in metastable Si0.86Ge0.14 by characterising the diffusion of a boron marker layer in samples with and without P+ and F+ implants. The effect of two F+ implantation energies (185keV and 42keV) was studied at two anneal temperatures 950°C and 1025°C. In samples implanted with P+ & 185keV F+, the fluorine suppresses boron transient enhanced diffusion completely at 950°C and suppresses thermal diffusion by 25% at 1025°C. In samples implanted with P+ & 42keV F+, the fluorine does not reduce boron transient enhanced diffusion at 950°C. This result is explained by the location of the boron marker layer in the vacancy-rich region of the fluorine damage profile for the 185keV implant but in the interstitial-rich region for the 42keV implant. Isolated dislocation loops are seen in the SiGe layer for the 185keV implant. We postulate that these loops are due to the partial relaxation of the metastable Si0.86Ge0.14 layer.

A New Practical Approach to Implement a Transient Enhanced Diffusion Model into an Fem-Based 2-D Process Simulator

1997 ◽  
Vol 490 ◽  
Author(s):  
Noriyuki Sugiyasu ◽  
Kaina Suzuki ◽  
Syuichi Kojima ◽  
Yasushi Ohyama
Keyword(s):  
Diffusion Model ◽  
Boron Diffusion ◽  
Combined Method ◽  
Solution System ◽  
Charge Neutrality ◽  
Robust Solution ◽  
Enhanced Diffusion ◽  
Transient Enhanced Diffusion ◽  
Vacancy Pair ◽  
Process Simulator

ABSTRACTWe have proposed a coupled and de-coupled combined method to solve partial differential equations for a transient enhanced diffusion model. In the case of a boron diffusion process, the sum of concentrations of interstitial Si and of impurity-interstitial pair, the sum of concentrations of vacancy and of impurity-vacancy pair and each chemical impurity concentration are kept constant. The charge neutrality law is also applied. This procedure has realized a robust solution system which is implemented into our in-house FEM-based 2-D process simulator, and transient enhanced diffusion simulations for a sub-quarter micron nMOSFET have been demonstrated.

Application of High Energy Ion Beam on the Control of Boron Diffusion

2003 ◽  
Vol 792 ◽  
Author(s):  
Wei-Kan Chu ◽  
Lin Shao ◽  
Jiarui Liu
Keyword(s):  
Point Defect ◽  
Point Defects ◽  
Anomalous Diffusion ◽  
Ion Beam ◽  
Surface Region ◽  
High Energy ◽  
Boron Diffusion ◽  
Defect Engineering ◽  
Projected Range ◽  
Ultrashallow Junction

ABSTRACTAnomalous diffusion of boron during annealing is a detriment on the fabrication of ultrashallow junction required by the next generation Si devices. This has driven the need to develop new doping methods. In the point defect engineering approach, high-energy ion bombardments inject vacancies near the surface region and create excessive interstitials near the end of projected range of incident ions. Such manipulation of point defects can retard boron diffusion and enhance activation of boron. We will review the current understanding of boron diffusion and our recent activities in point defect engineering.

A Comprehensive Model for Carbon Suppression of Boron Transient Enhanced Diffusion

2001 ◽  
Vol 669 ◽  
Author(s):  
Julie L. Ngau ◽  
Peter B. Griffin ◽  
James D. Plummer
Keyword(s):  
Point Defect ◽  
Recent Work ◽  
Comprehensive Model ◽  
Pairing Mechanism ◽  
Diffusion Behavior ◽  
Interstitial Carbon ◽  
Enhanced Diffusion ◽  
Transient Enhanced Diffusion ◽  
Single Temperature ◽  
Carbon Interstitial

ABSTRACTIn this work, the time evolution of B transient enhanced diffusion (TED) suppression due to the incorporation of 0.018% substitutional carbon in silicon was studied. The combination of having low C concentrations, which reduce B TED without completely eliminating it, and having diffused B profiles for several times at a single temperature provides much data upon which various models for the suppression of B TED can be tested. Recent work in the literature has indicated that the suppression of B TED in C-rich Si is caused by non-equilibrium Si point defect concentrations, specifically the undersaturation of Si self-interstitials, that result from the coupled out-diffusion of carbon interstitials via the kick-out and Frank-Turnbull reactions. Attempts to model our data with these two reactions revealed that the time evolved diffusion behavior of B was not accurately simulated and that an additional reaction that further reduces the Si self-inter- stitial concentration was necessary. In this work, we incorporate a carbon interstitial, carbon substitutional (CiCs) pairing mechanism into a comprehensive model that includes the C kick-out reaction, C Frank-Turnbull reaction, {311} defects, and boron interstitial clusters (BICs) and demonstrate that this model successfully simulates C suppression of B TED at 750 °C for anneal times ranging from 10 s to 60 min.

Sign in / Sign up

Export Citation Format

Share Document