scholarly journals BACK ANALYSIS OF THE RETAINING WALL AT JEMBER - BANYUWANGI ROAD KM 234+500

2019 ◽  
Vol 3 (1) ◽  
pp. 71
Author(s):  
Wisnu Sadewa Febryawan ◽  
Januar Fery Irawan ◽  
Luthfi Amri Wicaksono
Keyword(s):  
Secondary Structure ◽  
Bearing Capacity ◽  
Cross Section ◽  
Retaining Wall ◽  
Back Analysis ◽  
Strength Reduction ◽  
Reduction Stability

The retaining wall at Jember-Banyuwangi Road KM 234+500 consists of primer structure and secondary structure. The structure has a crack failure that the length is 2,5 m vertically. The back analysis is needed retaining wall stability and strength reduction stability. Methods used in stability calculations by Das method which calculate based on a failure of overturning, sliding, and bearing capacity, meanwhile strength reduction stability used by Plaxis program. The result stability calculations review Cross Section 1, 7, and 14 to check for overturning are 1,07 ; 1,29 ; 1,31 respectively, check for sliding are 0,87 ; 1,10 ; 1,16 respectively, check for bearing capacity failure are 6,64 ; 5,93 ; 6,83, check for strength reduction are 0,98 ; 0,99 ; 1,15 respectively. Dinding penahan tanah (DPT) di Jalan Raya Jember-Banyuwang KM 234+500 terdiri dari struktur utama dan struktur sekunder. Dinding penahan tanah tersebut mengalami kerusakan (crack) pada bagian atas struktur dengan panjang crack sepanjang 2,5 m secara vertikal. Diperlukan analisis balik stabilitas dinding penahan tanah dan pengurangan kekuatan untuk mengetahui penyebab kerusakan struktur DPT. Metode yang digunakan dalam perhitungan stabilitas tanah dengan metode Das yang meninjau cek terhadap guling, geser, dan kegagalan daya dukung, sedangkan stabilitas pengurangan kekuatan dengan program Plaxis. Hasil perhitungan stabilitas meninjau bagian struktur utama Cross Section 1, 7, 14 untuk cek terhadap guling masing-masing 1,07 ; 1,29 ; 1,31, cek terhadap geser masing-masing 0,87 ; 1,10 ; 1,16, cek terhadap kegagalan daya dukung masing-masing 6,64 ; 5,93 ; 6,83, cek terhadap pengurangan kekuatan 0,98 ; 0,99 ; 1,15.

Research of Direct Calculation Method for Design on Cross-Section of Retaining Wall

2013 ◽  
Vol 639-640 ◽  
pp. 714-717
Author(s):  
Wei Huang
Keyword(s):  
Bearing Capacity ◽  
Cross Section ◽  
Calculation Method ◽  
Calculated Result ◽  
Conversion Factor ◽  
Retaining Wall ◽  
Direct Calculation ◽  
Allowable Range ◽  
The Stability ◽  
Base Width

Based on meeting the requirement of ground bearing capacity, the allowable range of anti-overturning safety factor is derived. The relative parameters are expressed with base width and the relation graphs of conversion factor are presented, and then can design the cross-section of retaining wall directly by combining the stability requirement of anti-sliding. The calculated result shows that this method makes the design simple and reliable. It may be a reference for engineers.

SETTING A DIAGRAM APPROACH TO CALCULATING VIBRATED, CENTRIFUGED AND VIBROCENTRIFUGED REINFORCED CONCRETE COLUMNS WITH A VARIATROPIC STRUCTURE

2020 ◽  
pp. 22-34
Author(s):  
Л. Р. Маилян ◽  
С. А. Стельмах ◽  
Е. М. Щербань ◽  
М. П. Нажуев
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Cross Section ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
The Cross ◽  
Concrete Elements ◽  
Diagram Approach

Состояние проблемы. Железобетонные элементы изготавливаются, как правило, по трем основным технологиям - вибрированием, центрифугированием и виброцентрифугированием. Однако все основные расчетные зависимости для определения их несущей способности выведены, исходя из основного постулата - постоянства и равенства характеристик бетона по сечению, что реализуется лишь в вибрированных колоннах. Результаты. В рамках диаграммного подхода предложены итерационный, приближенный и упрощенный способы расчета несущей способности железобетонных вибрированных, центрифугированных и виброцентрифугированных колонн. Выводы. Расчет по диаграммному подходу показал существенно более подходящую сходимость с опытными данными, чем расчет по методике норм, а также дал лучшие результаты при использовании дифференциальных характеристик бетона, чем при использовании интегральных и, тем более, нормативных характеристик бетона. Statement of the problem. Reinforced concrete elements are typically manufactured according to three basic technologies - vibration, centrifugation and vibrocentrifugation. However, all the basic calculated dependencies for determining their bearing capacity were derived using the main postulate, i.e., the constancy and equality of the characteristics of concrete over the cross section, which is implemented only in vibrated columns. Results. Within the framework of the diagrammatic approach, iterative, approximate and simplified methods of calculating the bearing capacity of reinforced concrete vibrated, centrifuged and vibrocentrifuged columns are proposed. Conclusions. The calculation according to the diagrammatic approach showed a significantly better convergence with the experimental data than that using the method of norms, and also performs better when using differential characteristics of concrete than when employing integral and particularly standard characteristics of concrete.

scholarly journals Flexural bearing capacity and failure mechanism of CFRP-aluminum laminate beam with double-channel cross-section

2021 ◽  
Vol 28 (1) ◽  
pp. 139-152
Author(s):  
Teng Huang ◽  
Dongdong Zhang ◽  
Yaxin Huang ◽  
Chengfei Fan ◽  
Yuan Lin ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Bearing Capacity ◽  
Failure Mechanism ◽  
Cross Section ◽  
Failure Criterion ◽  
Failure Modes ◽  
Channel Cross Section ◽  
Fiber Layer ◽  
Flexural Bearing Capacity ◽  
Double Channel

Abstract In this study, the flexural bearing capacity and failure mechanism of carbon fiber-reinforced aluminum laminate (CARALL) beams with a double-channel cross-section and a 3/2 laminated configuration were experimentally and numerically studied. Two types of specimens using different carbon fiber layup configurations ([0°/90°/0°]3 and [45°/0°/−45°]3) were fabricated using the pressure molding thermal curing forming process. The double-channel CARALL beams were subjected to static three-point bending tests to determine their failure behaviors in terms of ultimate bearing capacity and failure modes. Owing to the shortcomings of the two-dimensional Hashin failure criterion, the user-defined FORTRAN subroutine VUMAT suitable for the ABAQUS/Explicit solver and an analysis algorithm were established to obtain a progressive damage prediction of the CFRP layer using the three-dimensional Hashin failure criterion. Various failure behaviors and mechanisms of the CARALL beams were numerically analyzed. The results indicated that the numerical simulation was consistent with the experimental results for the ultimate bearing capacity and final failure modes, and the failure process of the double-channel CARALL beams could be revealed. The ultimate failure modes of both types of double-channel CARALL beams were local buckling deformation at the intersection of the upper flange and web near the concentrated loading position, which was mainly caused by the delamination failure among different unidirectional plates, tension and compression failure of the matrix, and shear failure of the fiber layers. The ability of each fiber layer to resist damage decreased in the order of 90° fiber layer > 0° fiber layer > 45° fiber layer. Thus, it is suggested that 90°, 0°, and 45° fiber layers should be stacked for double-channel CARALL beams.

Finite Element Modeling of a Mechanically Stabilized Earth Trial Wall

2021 ◽  
pp. 036119812110164
Author(s):  
Andrew Lees ◽  
Michael Dobie
Keyword(s):  
Finite Element ◽  
Shear Strength ◽  
Retaining Wall ◽  
Back Analysis ◽  
Soil Parameters ◽  
Failure Behavior ◽  
Valuable Insight ◽  
Deformation And Failure ◽  
First Case ◽  
Soil Shear Strength

Polymer geogrid reinforced soil retaining walls have become commonplace, with routine design generally carried out by limiting equilibrium methods. Finite element analysis (FEA) is becoming more widely used to assess the likely deformation behavior of these structures, although in many cases such analyses over-predict deformation compared with monitored structures. Back-analysis of unit tests and instrumented walls improves the techniques and models used in FEA to represent the soil fill, reinforcement and composite behavior caused by the stabilization effect of the geogrid apertures on the soil particles. This composite behavior is most representatively modeled as enhanced soil shear strength. The back-analysis of two test cases provides valuable insight into the benefits of this approach. In the first case, a unit cell was set up such that one side could yield thereby reaching the active earth pressure state. Using FEA a test without geogrid was modeled to help establish appropriate soil parameters. These parameters were then used to back-analyze a test with geogrid present. Simply using the tensile properties of the geogrid over-predicted the yield pressure but using an enhanced soil shear strength gave a satisfactory comparison with the measured result. In the second case a trial retaining wall was back-analyzed to investigate both deformation and failure, the failure induced by cutting the geogrid after construction using heated wires. The closest fit to the actual deformation and failure behavior was provided by using enhanced fill shear strength.

scholarly journals Assessment of Rectangular Cavity in Concrete Gravity Retaining Wall using Finite Element Method

2019 ◽  
Vol 8 (4) ◽  
pp. 2656-2661
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Stress Distribution ◽  
Cross Section ◽  
Retaining Wall ◽  
Rectangular Cavity ◽  
Gravity Retaining Wall ◽  
The Cross ◽  
Conditions Of Stability ◽  
Element Method

The design of the Gravity retaining wall (GRW) is a trial and error process. Prevailing conditions of backfill are used to determine the profile of GRW, which proceeds with the selection of provisional dimensions. The optimum section is having factors of safety of stability higher than the allowable values and stresses in the cross-section smaller than permissible. The cross-section is designed to fulfill conditions of stability, subjected to very low stresses. The strength of the material, which is provided in the cross-section remains unutilized. A computer program is developed to find stresses at various locations on the cross-section of GRW using the Finite Element Method (FEM). A discontinuity in the form of a rectangular cavity is introduced in the cross-section of GRW to optimize it. The rectangular cavity is introduced in the cross-section of GRW at different locations. An attempt is made in this paper to find the stress distribution in the gravity retaining wall cross-section and to study the effect of the rectangular cavity on the stress distribution. Two cases representing different locations are considered to study the effect of the cavity. The location of the cavity is distinguished by the parameter w, the effects of cases with varied was 0.2305 (Case-I) and 0.1385 (Case-II) are observed. The cavity, which is provided not only makes the wall structurally efficient but also economically feasible.

scholarly journals Experimental and Numerical Study on Ultimate Shear Load Carrying Capacity of Corroded RC Beams

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Zhanzhan Tang ◽  
Zhixiang He ◽  
Zheng Chen ◽  
Lingkun Chen ◽  
Hanyang Xue ◽  
...  
Keyword(s):  
Shear Strength ◽  
Bearing Capacity ◽  
Cross Section ◽  
Loss Rate ◽  
Numerical Study ◽  
Rc Beams ◽  
Load Carrying ◽  
Shear Bearing Capacity ◽  
The Cross ◽  
The Impact

For an RC beam, the strength of steel rebar, the bonding strength between the concrete and reinforcement, and the bite action between the aggregates will deteriorate significantly due to corrosion. In the present study, 10 RC beams were designed to study the impact of corrosion on the shear bearing capacity. The mechanism of corrosion for stirrups and longitudinal bars and their effects were analyzed. Based on the existing experimental data, the correlation between the stirrup corrosion factor and the cross section loss rate was obtained. An effective prediction formula on the shear bearing capacity of the corroded RC beams was proposed and validated by the experimental results. Moreover, a numerical analysis approach based on the FE technique was proposed for the prediction of the shear strength. The results show that corrosion of the reinforcements could reduce the shear strength of the RC beams. The corrosion of stirrups can be numerically simulated by the reduction of the cross section. The formulae in the literature are conservative and the predictions are very dispersed, while the predictions by the proposed formula agree very well with the experiment results.

Shape Rolling Simulation of Tailor Rolled Blanks Based on Deform-3D

2011 ◽  
Vol 101-102 ◽  
pp. 897-900 ◽  
Author(s):  
Can Huang ◽  
Yi Gan ◽  
Ji Tao Du ◽  
Cheng Zhan Chen ◽  
Qi Jun Chen
Keyword(s):  
Simulation Model ◽  
Bearing Capacity ◽  
Cross Section ◽  
Rolling Process ◽  
Simple Analysis ◽  
Shape Rolling ◽  
Automotive Body ◽  
Flexible Rolling ◽  
Tailor Rolled Blanks ◽  
Deform 3D

Tailor rolled blanks (TRB) is made by flexible rolling system. And the thickness of TRB can be determined according to the load of this section. With its good bearing capacity and designed, it can be used to make automotive body for reducing the material and lower the weight. This paper describes the rolling process of TRB, and rolling simulation model of TRB was constructed using Deform-3D. The result curve of TRB rolling simulation was compared with a given target curve to determine the TRB rolling implementation, and had a simple analysis about the factors of each cross section during rolling. This research will give a guidance to realize the rolling of TRB.

Numerical Analysis on the Bearing Capacity of Single Pile in Deep Excavation Area

2013 ◽  
Vol 671-674 ◽  
pp. 226-229
Author(s):  
Jun Jie Wu ◽  
Jin Jian Chen ◽  
Shuai Jun Liu ◽  
Jian Hua Wang
Keyword(s):  
Bearing Capacity ◽  
Large Scale ◽  
Numerical Study ◽  
Back Analysis ◽  
Load Test ◽  
Deep Excavation ◽  
Static Load Test ◽  
Fem Modeling ◽  
Vertical Bearing ◽  
Element Technique

Large-scale deep excavation may affect the bearing capacity of piles inside the excavation zone. It does not only cause the loss of friction, but also change the stress state of the subsoil. In this paper, nonlinear finite element technique is employed to investigate the bearing capacity of piles influenced by the deep excavation. Parameters of soil are obtained by back analysis on the pile static load test results. The bearing capacity of the piles during excavation is analyzed by performing FEM modeling under three conditions using the calibrated parameters. The numerical study shows that the loss ratio of vertical bearing capacity of pile foundation caused by excavation unloading is 34%.

The Application Research and Discussion on a Viaduct Artificial Excavated Pile Technology

2012 ◽  
Vol 446-449 ◽  
pp. 2449-2452
Author(s):  
Dong Guo Li ◽  
Gui Mei Shi
Keyword(s):  
Bearing Capacity ◽  
Pile Foundation ◽  
Retaining Wall ◽  
Wall Effect ◽  
Construction Technology ◽  
Application Research ◽  
Technical Work ◽  
Bored Pile

A viaduct of the Qinglai expressway fourth contract was artificial excavated piles. The construction technical work was regarded as an example. The technical comparison were done between the artificial excavated pile and the bored pile on the pile foundation bearing capacity and the retaining wall effect . The artificial excavated pile replacing the bored pile was feasible, and the construction technology and the key problems of the artificial excavated piles were confirmed. The references were provided to the similar projects.

LOAD-BEARING CAPACITY OF CONCRETE-FILLED STEEL COLUMNS

2009 ◽  
Vol 15 (1) ◽  
pp. 21-33 ◽  
Author(s):  
Artiomas Kuranovas ◽  
Douglas Goode ◽  
Audronis Kazimieras Kvedaras ◽  
Shantong Zhong
Keyword(s):  
Bearing Capacity ◽  
Cross Section ◽  
Cross Sections ◽  
Rectangular Cross Section ◽  
Circular Cross Section ◽  
Steel Tube ◽  
Sustained Load ◽  
Load Bearing Capacity ◽  
Concrete Core ◽  
Load Bearing

This paper represents the analysis of 1303 specimens of CFST experimental data. Test results are compared with EC4 provided method for determining the load‐bearing capacity of these composite elements. Several types of CFSTs were tested: both circular and rectangular cross‐sections with solid and hollow concrete core with axial load applied without and with moment, with sustained load and preloading. For circular cross‐section columns there is a good agreement between the test failure load and the EC4 calculation for both short and long columns with and without moment. For rectangular cross‐section columns the agreement is good except when the concrete cylinder strength was greater than 75 MPa, when many tests failed below the strength predicted by EC4. Preloading the steel tube before filling with concrete seems to have no effect on the strength. This paper also presents the stress distribution, confinement distribution and complete average longitudinal stress‐strain curves for concrete‐filled steel tubular elements. Based on the definition of the “Unified Theory”, the CFST is looked upon as an entity of a new composite material. In this paper, the research achievement of the strength and stability for centrifugal‐hollow and solid concrete filled steel tube are introduced. These behaviours relate to the hollowness ratio and the confining indexes of corresponding solid CFST. If the hollow ratio equals to 0,4–0,5 and over, the N‐ϵ relationship exists in steady descending stage. The critical stress of CFST elements stability is determined as an eccentric member with the initial eccentricity by use of finite element method. Santrauka Straipsnyje analizuojami 1303 betonšerdžių plieninių strypų bandinių eksperimentiniai duomenys. Duomenys lyginami su eurokode 4 pateiktais kompozitinių elementų laikomosios galios nustatymo metodais. Analizuojami šie betonšerdžių plieninių strypų bandinių tipai: pilnaviduriai ir tuščiaviduriai, apskrito ir stačiakampio skerspjūvio kolonos, kurių galuose veikia arba neveikia momentas, su iš anksto pridėta arba ilgalaike apkrova. Apskrito skerspjūvio kolonų laikomosios galios bandymų rezultatai atitinka skaičiavimų reikšmes, apskaičiuotas pagal eurokode 4 pateiktu metodu. Stačiakampio skerspjūvio elementų laikomosios galios reikšmių bandymo rezultatai puikiai atitinka teorines reikšmes, kai betono ritininis stipris nesiekia 75 MPa. Išankstinis elementų apkrovimas poveikio elementų laikomajai galiai beveik neturi. Taip pat nagrinėjami betonšerdžių elementų įtempių būvių pasiskirstymas, betono apspaudimo poveikis ir išilginių deformacijų ir įtempių kreivės. Pateikiama S. T. Zhong „Unifikuota teorija“, kuri nagrinėja kompozitinį elementą kaip visumą. Straipsnyje nagrinėjamos kompozitinio plieninio ir betoninio elemento stiprumo ir pastovumo sąlygos. Tokių elementų reikšmėmis. Jeigu tuštumos santykis lygus 0,4–0,5 ir daugiau, N-ε sąryšis yra kritimo stadijoje. Elgsenos stadijos keičiasi pagal tuštumos koeficientą.

Sign in / Sign up

Export Citation Format

Share Document