scholarly journals 3D Simulation of Incompressible Poiseuille Flow through 180° Curved Duct of Square Cross-section under Effect of Thermal Buoyancy

2019 ◽  
Vol 63 (4) ◽  
pp. 257-269 ◽  
Author(s):  
Mourad Mokeddem ◽  
Houssem Laidoudi ◽  
Oluwole Daniel Makinde ◽  
Mohamed Bouzit
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Rate ◽  
Cross Section ◽  
Transfer Rate ◽  
Richardson Number ◽  
Dean Number ◽  
Thermal Buoyancy ◽  
Dimensionless Velocity ◽  
Curved Duct

In this paper, three-dimensional numerical simulations are carried out to investigate and analyze the gradual effects of thermal buoyancy strength on laminar flow of an incompressible viscous fluid and heat transfer rate inside a 180° curved channel of square cross-section. The governing equations of continuity, momentum and energy balance are obtained and solved numerically using finite volume method. The effect of Dean number, De, and Richardson number, Ri, on dimensionless velocity profiles and Nusselt number are examined for the conditions: De = 125 to 150, Ri = 0 to 2 at Pr = 1. The mean results are illustrated in terms of streamline and isotherm contours to interpret the flow behaviors and its effect on heat transfer rate. Dimensionless velocity profiles and the local Nusselt number at the angle 0° and 90° are presented and discussed. Also, the average Nusselt number on surfaces of curved duct is computed. The obtained results showed that by adding thermal buoyancy to computed domain, some early Dean vortices are observed at the angle 0° and new sort are observed at 90°. Furthermore, increase in Dean number increases the heat transfer rate. In other hand, increase in Richardson number decreases the average Nusselt number of 180° curved duct.

Simulation of Non Newtonian Power-Law Fluid Flows and Mixed Convection Heat Transfer inside of Curved Duct

2017 ◽  
Vol 378 ◽  
pp. 113-124 ◽  
Author(s):  
Bouzit Fayçal ◽  
Houssem Laidoudi ◽  
Mohamed Bouzit
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Power Law ◽  
Transfer Rate ◽  
Richardson Number ◽  
Flow Behavior ◽  
Thermal Buoyancy ◽  
Flow And Heat Transfer ◽  
Curved Duct ◽  
Power Law Fluids

A two-dimensional numerical simulation is carried out to understand the combined effects of thermal buoyancy strength and rheological flow behavior of non Newtonian power-law fluids on laminar flow and heat transfer rate through a 180° curved duct. The governing equations including the full Navier-Stokes, the continuity and the energy are solved using the commercial code ANSYS-CFX. The numerical results are presented and discussed for the range of conditions as: Re = 40 to 1000, Ri = 0 to 1 and n = 0.4 to 1.2 for fixed value of Prandt number of Pr = 1. In order to analyze the obtained results, the representative streamlines and isotherm patterns are presented. The average Nusselt number of the inner and outer walls of duct is computed to determine the role of Reynolds number, Richardson number and power-law index on flow and heat transfer. It is found that increase in Richardson number creates alternative vortices on duct walls. Moreover, the alternative vortices enhance the heat transfer rate for shear thinning, Newtonian and shear thickening fluids.

scholarly journals Effect of thermal buoyancy on flow pattern from a pair of side-by-side confined triangular cylinders

2020 ◽  
Vol 55 (1) ◽  
pp. 9-14
Author(s):  
H Laidoudi ◽  
M Bouzit
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Drag Coefficient ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Richardson Number ◽  
Average Nusselt Number ◽  
Convection Heat Transfer ◽  
Thermal Buoyancy ◽  
Energy Equations

The effects of ax ial and radial thermal buoyancy on fluid flow and mixed convection heat transfer from a pair of identical triangular cylinders in side-by-side arrangement confined within a straight channel. The numerical simulations are carried out by solving continuity, momentum and energy equations using the commercial code ANSYS-CFX. The obtained results are presented and discussed within the range of following conditions: Richardson number Ri = 0 to 2, Reynolds Re = 20, and Prandtl number Pr = 1 at fixed value of blockage ratio β = 0.2. The main results are depicted in terms of streamline and isotherm contours to analyze the fluidic and energetic behaviors. The total drag coefficient and average Nusselt number are also computed. Moreover, a simple correlation indicating the variations of drag coefficient and average Nusselt number versus Richardson number are also provided. It was found that for axial effect of thermal buoyancy, increase in buoyancy strength enhances the heat transfer rate for both cylinders. In other hand, for radial effect, increase in buoyancy strength increases the heat transfer rate of down cylinder and it is reduced for the upper cylinder. Bangladesh J. Sci. Ind. Res.55(1), 9-14, 2020

Numerical simulation of water/alumina nanofluid mixed convection in square lid-driven cavity

2019 ◽  
Vol 30 (5) ◽  
pp. 2781-2807
Author(s):  
Davood Toghraie ◽  
Ehsan Shirani
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Richardson Number ◽  
Hartmann Number ◽  
Two Phase ◽  
Content Type ◽  
Driven Cavity

Purpose The purpose of this paper is to investigate the mixed convection of a two-phase water–aluminum oxide nanofluid in a cavity under a uniform magnetic field. Design/methodology/approach The upper wall of the cavity is cold and the lower wall is warm. The effects of different values of Richardson number, Hartmann number, cavitation length and solid nanoparticles concentration on the flow and temperature field and heat transfer rate were evaluated. In this paper, the heat flux was assumed to be constant of 10 (W/m2) and the Reynolds number was assumed to be constant of 300 and the Hartmann number and the volume fraction of solid nanoparticles varied from 0 to 60 and 0 to 0.06, respectively. The Richardson number was considered to be 0.1, 1 and 5. Aspect ratios were 1, 1.5 and 2. Findings Comparison of the results of this paper with the results of the numerical and experimental studies of other researchers showed a good correlation. The results were presented in the form of velocity and temperature profiles, stream and isotherm lines and Nusselt numbers. The results showed that by increasing the Hartmann number, the heat transfer rate decreases. An increase from 0 to 20 in Hartmann number results in a 20 per cent decrease in Nusselt numbers, and by increasing the Hartmann number from 20 to 40, a 16 per cent decrease is observed in Nusselt number. Accordingly, it is inferred that by increasing the Hartmann number, the reduction in the Nusselt number is decreased. As the Richardson number increased, the heat transfer rate and, consequently, the Nusselt number increased. Therefore, an increase in the Richardson number results in an increase of the Nusselt number, that is, an increase in Richardson number from 0.1 to 1 and from 1 to 5 results in 37 and 47 per cent increase in Nusselt number, respectively. Originality/value Even though there have been numerous investigations conducted on convection in cavities under various configurations and boundary conditions, relatively few studies are conducted for the case of nanofluid mixed convection in square lid-driven cavity under the effect of magnetic field using two-phase model.

3D Simulation of Dean Vortices at 30° Position of 180° Curved Duct of Square Cross-Section under Opposing Buoyancy

2018 ◽  
Vol 389 ◽  
pp. 153-163 ◽  
Author(s):  
Mourad Mokeddem ◽  
Houssem Laidoudi ◽  
Mohamed Bouzit
Keyword(s):  
Cross Section ◽  
Richardson Number ◽  
Three Dimensions ◽  
Governing Equations ◽  
Dean Number ◽  
Thermal Buoyancy ◽  
Dean Vortices ◽  
Flow And Heat Transfer ◽  
Curved Duct ◽  
Physical Phenomena

3D numerical simulations are performed to analyze correctly the effect of opposing thermal buoyancy and Dean number on Dean vortices, fluid flow and heat transfer through 180° curved duct of square cross-section. Due to tremendous found results, this works emphasizes only at the position 30° of the bend portion. The governing equations involving momentum, continuity and energy are solved in three dimensions under these assumptions: the flow is laminar, steady-state and incompressible. The present study is investigated in the range of these conditions: Dean number of De = 125 to 150, Richardson number of Ri = 0 to 2 at Pr = 1. The principal obtained results are represented in forms of streamlines and isotherms to analyze and to discuss the found physical phenomena. The local Nusselt number along the wall of square cross-section is also computed and presented. The main found point is that the opposing thermal buoyancy has a tendency to eliminate the effect of centrifugal force at the position 30° of bend portion of 180° curved duct.

scholarly journals Natural Convection from Four Circular Cylinders in Across Arrangement within Horizontal Annular Space

2020 ◽  
Vol 14 (2) ◽  
pp. 98-102
Author(s):  
Houssem Laidoudi
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Prandtl Number ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Initial Conditions ◽  
Fluid Motion ◽  
Circular Cylinders ◽  
Thermal Buoyancy

AbstractNumerical investigation is accomplished to study the roles of governing parameters of natural convection on the fluid motion and heat transfer rate of four heated circular cylinders placed inside a circular enclosure of cold surface. The cylinders are positioned in across arrangement. The representative results are obtained within the ranges of initial conditions as: Prandtl number (Pr = 7.1 to 1000) and Rayleigh number (Ra = 103 to 105). The average Nusselt number of each inner cylinder is computed. The effects of thermal buoyancy strength on the fluid motion and temperature are also illustrated. It was found that the heat transfer rate of cylinders depends significantly on the position inside the enclosure. Moreover, the role of Prandtl number on flow and thermal patterns is negligible. The values of Nusselt number are also given, which can be useful for some engineering applications.

The Flow and Mixed Convection around Tandem Circular Cylinders at Low Reynolds Number

2017 ◽  
Vol 378 ◽  
pp. 59-67
Author(s):  
Houssem Laidoudi ◽  
Blissag Bilal ◽  
Mohamed Bouzit
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Mixed Convection ◽  
Drag Coefficient ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Richardson Number ◽  
Circular Cylinders ◽  
Thermal Buoyancy ◽  
Flow And Heat Transfer

A numerical investigation is carried out to understand the effects of thermal buoyancy and Reynolds number on flow characteristics and mixed convection heat transfer over three isothermal circular cylinders situated in a tandem arrangement within a horizontal channel. The distance between cylinders is fixed at the value of 2.5 widths of the cylinder. The obtained results are presented and discussed for the range of conditions as: Re = 5 to 40, Ri = 0 to 2 at fixed Pr number of 1 and blockage ratio β = 0.25. The main results are depicted in terms of streamlines and isotherm contours to analyze the effect of thermal buoyancy on fluid flow and heat transfer rate. Moreover, the overall drag coefficient and Nusselt number are computed to elucidate the role of Reynolds number and Richardson number on the flow and heat transfer. It is found that increase in the Richardson number increases the drag coefficient of the upstream cylinder whereas it decreases the heat transfer rate of this cylinder. The superimposed of thermal buoyancy created a new sort of recirculation zones between the tandem cylinders.

Heat Transfer Investigation of a Tube Partially Wrapped by Metal Porous Layer as a Potential Novel Tube for Air Cooled Heat Exchangers

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
M. Mohammadpour-Ghadikolaie ◽  
M. Saffar-Avval ◽  
Z. Mansoori ◽  
N. Alvandifar ◽  
N. Rahmati
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Rate ◽  
Porous Layer ◽  
Transfer Rate ◽  
Metal Foam ◽  
Convection Heat Transfer ◽  
Darcy Number ◽  
High Heat Transfer

Laminar forced convection heat transfer from a constant temperature tube wrapped fully or partially by a metal porous layer and subjected to a uniform air cross-flow is studied numerically. The main aim of this study is to consider the thermal performance of some innovative arrangements in which only certain parts of the tube are covered by metal foam. The combination of Navier–Stokes and Darcy–Brinkman–Forchheimer equations is applied to evaluate the flow field. Governing equations are solved using the finite volume SIMPLEC algorithm and the effects of key parameters such as Reynolds number, metal foam thermophysical properties, and porous layer thickness on the Nusselt number are investigated. The results show that using a tube which is fully wrapped by an external porous layer with high thermal conductivity, high Darcy number, and low drag coefficient, can provide a high heat transfer rate in the high Reynolds number laminar flow, increasing the Nusselt number almost as high as 16 times compared to a bare tube. The most important result of thisstudy is that by using some novel arrangements in which the tube is partially covered by the foam layer, the heat transfer rate can be increased at least 20% in comparison to the fully wrapped tube, while the weight and material usage can be considerably reduced.

Heat Transfer for Laminar Flow in Spiral Ducts of Rectangular Cross Section

2005 ◽  
Vol 127 (3) ◽  
pp. 352-356 ◽  
Author(s):  
Michael W. Egner ◽  
Louis C. Burmeister
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Cross Section ◽  
Rectangular Cross Section ◽  
Three Dimensional ◽  
Radius Of Curvature ◽  
Dean Number ◽  
Aspect Ratios ◽  
Small Pitch

Laminar flow and heat transfer in three-dimensional spiral ducts of rectangular cross section with aspect ratios of 1, 4, and 8 were determined by making use of the FLUENT computational fluid dynamics program. The peripherally averaged Nusselt number is presented as a function of distance from the inlet and of the Dean number. Fully developed values of the Nusselt number for a constant-radius-of-curvature duct, either toroidal or helical with small pitch, can be used to predict those quantities for the spiral duct in postentry regions. These results are applicable to spiral-plate heat exchangers.

3D optimization of baffle arrangement in a multi-phase nanofluid natural convection based on numerical simulation

2019 ◽  
Vol 30 (5) ◽  
pp. 2583-2605 ◽  
Author(s):  
Mohammad Mohsen Peiravi ◽  
Javad Alinejad ◽  
D.D. Ganji ◽  
Soroush Maddah
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Target Function ◽  
Optimal Arrangement ◽  
Content Type ◽  
Multi Phase

Purpose The purpose of this study is investigating the effect of using multi-phase nanofluids, Rayleigh number and baffle arrangement simultaneously on the heat transfer rate and Predict the optimal arrangement type of baffles in the differentiation of Rayleigh number in a 3D enclosure. Design/methodology/approach Simulations were performed on the base of the L25 Taguchi orthogonal array, and each test was conducted under different height and baffle arrangement. The multi-phase thermal lattice Boltzmann based on the D3Q19 method was used for modeling fluid flow and temperature fields. Findings Streamlines, isotherms, nanofluid volume fraction distribution and Nusselt number along the wall surface for 104 < Ra < 108 have been demonstrated. Signal-to-noise ratios have been analyzed to predict optimal conditions of maximize and minimize the heat transfer rate. The results show that by choosing the appropriate height and arrangement of the baffles, the average Nusselt number can be changed by more than 57 per cent. Originality/value The value of this paper is surveying three-dimensional and two-phase simulation for nanofluid. Also using the Taguchi method for Predicting the optimal arrangement type of baffles in a multi-part enclosure. Finally statistical analysis of the results by using of two maximum and minimum target Function heat transfer rates.

scholarly journals Mixed convective hybrid nanofluid flow in lid-driven undulated cavity: effect of MHD and Joule heating

2019 ◽  
Vol 16 (2) ◽  
pp. 109-126 ◽  
Author(s):  
Ishrat Zahan ◽  
R Nasrin ◽  
M A Alim
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Rate ◽  
Joule Heating ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Hybrid Nanoparticles ◽  
Wave Number ◽  
Hybrid Nanofluid

A numerical analysis has been conducted to show the effects of magnetohydrodynamic (MHD) and Joule heating on heat transfer phenomenon in a lid driven triangular cavity. The heat transfer fluid (HTF) has been considered as water based hybrid nanofluid composed of equal quantities of Cu and TiO2 nanoparticles. The bottom wall of the cavity is undulated in sinusoidal pattern and cooled isothermally. The left vertical wall of the cavity is heated while the inclined side is insulated. The two dimensional governing partial differential equations of heat transfer and fluid flow with appropriate boundary conditions have been solved by using Galerkin's finite element method built in COMSOL Multyphysics. The effects of Hartmann number, Joule heating, number of undulation and Richardson number on the flow structure and heat transfer characteristics have been studied in details. The values of Prandtl number and solid volume fraction of hybrid nanoparticles have been considered as fixed. Also, the code validation has been shown. The numerical results have been presented in terms of streamlines, isotherms and average Nusselt number of the hybrid nanofluid for different values of governing parameters. The comparison of heat transfer rate by using hybrid nanofluid, Cu-water nanofluid,  TiO2 -water nanofluid and clear water has been also shown. Increasing wave number from 0 to 3 enhances the heat transfer rate by 16.89%. The enhanced rate of mean Nusselt number for hybrid nanofluid is found as 4.11% compared to base fluid.

Sign in / Sign up

Export Citation Format

Share Document