27. Metal Working Fluid Assessment at the Coast Mountain Bus Company Fleet Overhaul Center

2005 ◽  
Author(s):  
C. Lynch ◽  
K. Bartlett
Keyword(s):  
Working Fluid ◽  
Metal Working ◽  
Fluid Assessment

6. Evaluation of Five Extraction Protocols for Determination of Endotoxin in Metal Working Fluid Aerosol

2001 ◽  
Author(s):  
K. Bartlett ◽  
J. Phipps ◽  
K. Kulhankova ◽  
P. Thorne
Keyword(s):  
Working Fluid ◽  
Metal Working

425. An Evaluation of Metal Working Fluid Mist Generation at a Machining Center

1999 ◽  
Author(s):  
W. Heitbrink ◽  
G. Dye ◽  
A. Spencer
Keyword(s):  
Working Fluid ◽  
Metal Working ◽  
Machining Center

Studying the lubricity of new eco-friendly cutting oil formulation in metal working fluid

2018 ◽  
Vol 70 (9) ◽  
pp. 1569-1579 ◽  
Author(s):  
M.R. Noor El-Din ◽  
Marwa R. Mishrif ◽  
Satish V. Kailas ◽  
Suvin P.S. ◽  
Jagadeesh K. Mannekote
Keyword(s):  
Surface Morphology ◽  
Corrosion Inhibitor ◽  
Castor Oil ◽  
Cutting Fluid ◽  
Working Fluid ◽  
Cutting Fluids ◽  
Metal Working ◽  
Content Type ◽  
Metalworking Fluid ◽  
3D Profilometer

PurposeThis paper aims to formulate a new metal working fluid (MWF) composition including some eco-friendly emulsifiers, corrosion inhibitor, biocide, and non- edible vegetable oil (castor oil) as the base oil. To achieve this aim, five MWFs with different hydrophilic–lipophilic balance (HLB) value as 10, 9.5, 9, 8.5 and 8 were prepared to identify the optimum HLB value that gives a highly stable oil-in-water emulsion. The performance of castor oil based MWF was evaluated using tool chip tribometer and drill dynamometer. The surface morphology of steel disc and friction pin was performed using scanning electron microscope (SEM) and 3D profilometer. The results revealed that the use of the prepared cutting fluid (E1) caused the cutting force to decrease from 500 N for dry high-speed steel sample to 280N, while the same value for a commercial cutting fluid (COM) was recorded as 340 N at drilling speed and cutting feed force as 1120 rpm and 4 mm/min., respectively.Design/methodology/approachA castor oil-based metalworking fluid was prepared using nonionic surfactants. The composition of the metalworking fluid was further optimized by adding performance-enhancing additives. The performance of castor oil based MWF was analyzed using Tool chip tribometer and Drill dynamometer. The surface morphology of steel ball and a disc was done using 3D profilometer and SEM.FindingsStudies revealed that castor oil-based MWF having Monoethanolamine (MEA) as corrosion inhibitor was found to be highly stable. The drilling dynamometer and tool chip tribometer studies showed that castor oil-based MWF performance was comparable to that of commercial MWF.Research limitations/implicationsThis study aims to explore the performance of the castor oil based metalworking fluid (MWF) using tool chip tribometer and drill dynamometer.Practical implicationsThe conventional MWFs are petroleum derives and are unsustainable. Use of non-edible plant-based oils for preparing the MWF will not only be conserved environment but also add value addition to agricultural crops.Social implicationsThe social Implications is aiming to decrease the environmental impact that results from the using of mineral cutting fluids.Originality/valueThe originality of this work is to replace the mineral oil and synthetic oil based cutting fluids with more eco-friendly alternatives one. In addition, the investigation will focus on developing functional additives required for cutting fluids which are environmentally benign.

Respiratory effect of acute and subacute exposure to endotoxin-contaminated metal working fluid (MWF) aerosols on Sprague-Dawley rats

2005 ◽  
Vol 79 (6) ◽  
pp. 321-329 ◽  
Author(s):  
Cheol-Hong Lim ◽  
Il Je Yu ◽  
Hyeon-Young Kim ◽  
Seung-Bae Lee ◽  
Min-Gu Kang ◽  
...  
Keyword(s):  
Working Fluid ◽  
Metal Working ◽  
Sprague Dawley ◽  
Respiratory Effect ◽  
Sprague Dawley Rats ◽  
Subacute Exposure

scholarly journals Comparative Life Cycle Assessment of a microalgae-based oil metal working fluid with its petroleum-based and vegetable-based counterparts

2022 ◽  
pp. 130506
Author(s):  
Mélanie Guiton ◽  
David Suárez-Montes ◽  
Rubén Sánchez ◽  
Paul Baustert ◽  
Christos Soukoulis ◽  
...  
Keyword(s):  
Life Cycle Assessment ◽  
Life Cycle ◽  
Working Fluid ◽  
Metal Working ◽  
Comparative Life Cycle Assessment

Microbial Contaminants Contribute to the Inflammatory Effect of Metal Working Fluid in a Murine Model

2007 ◽  
Vol 119 (1) ◽  
pp. S266
Author(s):  
M.C. Zacharisen ◽  
C.S. Barrios ◽  
V.P. Kurup ◽  
J.N. Fink
Keyword(s):  
Murine Model ◽  
Working Fluid ◽  
Metal Working ◽  
Microbial Contaminants ◽  
Inflammatory Effect

Size-Selective Pulmonary Dose Indices for Metal-Working Fluid Aerosols in Machining and Grinding Operations in the Automobile Manufacturing Industry

AIHAJ ◽  
1994 ◽  
Vol 55 (1) ◽  
pp. 20-29 ◽  
Author(s):  
Susan R. Woskie ◽  
Thomas J. Smith ◽  
Marilyn F. Hallock ◽  
S. Katharine Hammond ◽  
Frank Rosenthal ◽  
...  
Keyword(s):  
Manufacturing Industry ◽  
Working Fluid ◽  
Metal Working ◽  
Automobile Manufacturing ◽  
Grinding Operations
Sign in / Sign up

Export Citation Format

Share Document