scholarly journals A Comprehensive Coal Reservoir Classification Method Base on Permeability Dynamic Change and Its Application

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 644 ◽  
Author(s):  
Xinlu Yan ◽  
Songhang Zhang ◽  
Shuheng Tang ◽  
Zhongcheng Li ◽  
Yongxiang Yi ◽  
...  
Keyword(s):  
Coalbed Methane ◽  
Dynamic Change ◽  
Initial Permeability ◽  
Gas Production ◽  
Gas Desorption ◽  
Reservoir Permeability ◽  
Geological Conditions ◽  
Production Stages ◽  
Productivity Potential ◽  
Coal Reservoir

Due to the unique adsorption and desorption characteristics of coal, coal reservoir permeability changes dynamically during coalbed methane (CBM) development. Coal reservoirs can be classified using a permeability dynamic characterization in different production stages. In the single-phase water flow stage, four demarcating pressures are defined based on the damage from the effective stress on reservoir permeability. Coal reservoirs are classified into vulnerable, alleviative, and invulnerable reservoirs. In the gas desorption stage, two demarcating pressures are used to quantitatively characterize the recovery properties of permeability based on the recovery effect of the matrix shrinkage on permeability, namely the rebound pressure (the pressure corresponding to the lowest permeability) and recovery pressure (the pressure when permeability returns to initial permeability). Coal reservoirs are further classified into recoverable and unrecoverable reservoirs. The physical properties and influencing factors of these demarcating pressures are analyzed. Twenty-six wells from the Shizhuangnan Block in the southern Qinshui Basin of China were examined as a case study, showing that there is a significant correspondence between coal reservoir types and CBM well gas production. This study is helpful for identifying geological conditions of coal reservoirs as well as the productivity potential of CBM wells.

scholarly journals Quantitative optimization of drainage strategy of coalbed methane well based on the dynamic behavior of coal reservoir permeability

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Xinlu Yan ◽  
Songhang Zhang ◽  
Shuheng Tang ◽  
Zhongcheng Li ◽  
Qian Zhang ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Dynamic Behavior ◽  
Water Flow ◽  
Coalbed Methane ◽  
Single Phase ◽  
Reservoir Permeability ◽  
Geological Conditions ◽  
Cbm Production ◽  
Coal Reservoir ◽  
Flow Stage

AbstractThe development of coalbed methane (CBM) is not only affected by geological factors, but also by engineering factors, such as artificial fracturing and drainage strategies. In order to optimize drainage strategies for wells in unique geological conditions, the characteristics of different stages of CBM production are accurately described based on the dynamic behavior of the pressure drop funnel and coal reservoir permeability. Effective depressurization is achieved by extending the pressure propagation radius and gas desorption radius to the well-controlled boundary, in the single-phase water flow stage and the gas–water flow stage, respectively, with inter-well pressure interference accomplished in the single-phase gas flow stage. A mathematic model was developed to quantitatively optimize drainage strategies for each stage, with the maximum bottom hole flow pressure (BHFP) drop rate and the maximum daily gas production calculated to guide the optimization of CBM production. Finally, six wells from the Shizhuangnan Block in the southern Qinshui Basin of China were used as a case study to verify the practical applicability of the model. Calculation results clearly indicate the differences in production characteristics as a result of different drainage strategies. Overall, if the applied drainage strategies do not achieve optimal drainage results, the coal reservoir could be irreversibly damaged, which is not conducive to expansion of the pressure drop funnel. Therefore, this optimization model provides valuable guidance for rational CBM drainage strategy development and efficient CBM production.

Influence of Engineering Measurements on the Desorption and Production of CBM Wells by Eclipse

2013 ◽  
Vol 868 ◽  
pp. 700-704 ◽  
Author(s):  
Rui Wang ◽  
Fan Dong ◽  
Qing Zhong Zhu ◽  
Yan Hui Yang ◽  
Tian Peng Yao
Keyword(s):  
Coalbed Methane ◽  
Production Capacity ◽  
Gas Production ◽  
Simulation Software ◽  
Stage Of Development ◽  
Cbm Production ◽  
Stable Yield ◽  
Yield Time ◽  
Coal Reservoir ◽  
The Impact

Desorption of Coalbed Methane is one of the key controls to CBM recovery ratio and production capacity. This paper discusses the impact of engineered measures on CBM overall desorption and production capacity with CBM model of Eclipse numerical simulation software. The simulation results show that: with the extension of hydraulic fracture half-length, overall desorption of coal reservoir increased and CBM production capacity improved, daily gas production, maximum gas production and stable yield time increased correspondingly; in different deployment of spacing and well network, the smaller spacing is beneficial to the overall desorption of coal reservoir, but its production can not keep stability because of the serious decline in the late stage of development, while the larger spacing shows in the opposite way.

Impact of Various Parameters on the Production of Coalbed Methane

SPE Journal ◽  
2013 ◽  
Vol 18 (05) ◽  
pp. 910-923 ◽  
Author(s):  
Zhongwei Chen ◽  
Jishan Liu ◽  
Akim Kabir ◽  
Jianguo Wang ◽  
Zhejun Pan
Keyword(s):  
Time Constant ◽  
Coalbed Methane ◽  
Dominant Role ◽  
Gas Production ◽  
Fracture Permeability ◽  
Permeability Model ◽  
Gas Desorption ◽  
Desorption Time ◽  
Matrix Blocks ◽  
Cbm Production

Summary Coalbed-methane (CBM) reservoirs are naturally fractured formations, comprising both permeable fractures and matrix blocks. The interaction between fractures and matrix presents a great challenge for the forecast of CBM reservoir performance. In this work, a dual-permeability model was applied to study the parameter sensitivity on the CBM production, because the dual-permeability model incorporates not only the influence from matrix and fractures but also that between adjacent matrix blocks. The mass exchange between two systems is defined as a function of desorption time constant at the standard condition, coal matrix porosity, and the difference of gas pressure between two systems. Correspondingly, gas diffusivity in matrix is considered as a variable and represented by a function of shape factor, gas desorption time, and reservoir pressure. These relations are integrated into a fully coupled numerical model of coal geomechanical deformation and gas desorption/gas flow in both systems. This numerical approach demonstrates the important nonlinear effects of the complex interaction between matrix and fractures on CBM production behaviors that cannot be recovered without rigorously incorporating geomechanical influences. This model was then used to investigate the sensitivity of CBM extraction behavior to different controlling factors, including gas desorption time constant, initial fracture permeability, fracture spacing, swelling capacity, desorption capacity, production pressure, and fracture and matrix porosities. Modeling results show that the peak magnitudes of gas-production rate increase with initial fracture permeability, sorption and swelling capacities, and matrix porosity, and decrease with gas desorption time constant and production pressure. These results also show dramatic increase in gas-production efficiency with decreasing magnitudes of fracture spacing. The comparison of the transient contributions of the desorbed gas and the free phase gas from the matrix system to gas production shows that the free phase gas plays the dominant role at the early stage, but diminishes when the adsorption phase gas takes over the dominant role, indicating the necessity of incorporating free phase gas impact in simulation models. The numerical model was also applied to match the history data from a gas-production well. A better matching result than that for the single-permeability model demonstrates the potential capability of the dual-permeability model for the forecast of CBM production.

Control Mechanism of the Effective Stress on Nano-Micro Pores and the Permeability of High-Rank Coals

2021 ◽  
Vol 21 (1) ◽  
pp. 484-494
Author(s):  
Xiaofeng Ji ◽  
Dangyu Song ◽  
Shaokai Yu ◽  
Kaikai He ◽  
Yunbo Li
Keyword(s):  
Pore Pressure ◽  
Effective Stress ◽  
Gas Adsorption ◽  
Initial Permeability ◽  
High Rank ◽  
Control Factors ◽  
Reservoir Permeability ◽  
Variation Mechanism ◽  
Coal Reservoir ◽  
The Impact

To study the change and main control factors of the high-rank coal reservoir permeability in deep coal seams, permeability tests under different stresses and gas pressures were carried out in the laboratory. The development and distribution of nano-micro pores and fractures in the coal matrix were analyzed and observed by mercury intrusion porosimetry, gas adsorption, scanning electron microscope and computed tomography to reveal the permeability variation mechanism. The results showed that the initial permeability of the coal samples ranged from 0.0114 mD to 0.2349 mD when the effective stress was 0 MPa, and it clearly varied among different samples. The permeability of all the coal samples was very sensitive to the effective stress and decreased exponentially with the increase of the effective stress. The increase of the pore pressure also led to a decrease of the permeability, whereas the impact of the pore pressure on permeability was less obvious compared with the effective stress. Sub-nanopores, nanopores, micro-fractures and larger fractures are all developed in the coal samples. Connected larger fractures were the main gas migration channels in permeability determination, and the narrowing, disconnection, and closure of the fractures caused by the increase of the effective stress were the most important reasons for significant reduction of permeability.

Dynamic Variation Character of CBM Reservoir Permeability during Depletion of High-Rank Coalbed Methane

2011 ◽  
Vol 233-235 ◽  
pp. 2267-2271
Author(s):  
Gui Zhong Li ◽  
Ze Deng ◽  
Bo Wang ◽  
Meng Geng
Keyword(s):  
Coalbed Methane ◽  
Geological Structure ◽  
Initial Permeability ◽  
Rapid Decline ◽  
Low Permeability ◽  
Late Development ◽  
Dynamic Variation ◽  
Permian System ◽  
Reservoir Permeability ◽  
Production Wells

China is rich in CBM resources, but so far, some production wells present low production and rapid decline trend. In addition to these objective factors such as low permeability and complexity of geological structure of CBM reservoir, there is still the most important problem during the exploitation techniques that is the lack of understanding to dynamic variation character of CBM reservoir permeability, which leads to the unreasonable work of depletion for coalbed methane.Using P&M model and parameters from 3# coal seam of Shanxi Formation, Permian system in Qinshui basin, the permeability variations of this block (first decline, then ascend, reaching 2.8 times of initial permeability at the end) were analyzed, revealing good depletion prospect of this CBM field, and pointed that the higher Young's modulus is, the more obvious matrix shrinkage is and the higher gas saturation is, the more favor for permeability improvement through sensitivity analysis. Finally, two suggestions were proposed, (1) add the 'permeability variations' to the parameters for CBM block select, which may find the "innate" in the late development of the poor condition of properties easy to improve, develop potential for larger blocks. (2) Adjust and optimize the depletion method (amplitude and frequency of bleeding, pressure reduction) according to the permeability variation characters discussed in this paper

scholarly journals A Thermo-Hydro-Mechanical-Chemical Coupling Model and Its Application in Acid Fracturing Enhanced Coalbed Methane Recovery Simulation

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 626 ◽  
Author(s):  
Chaojun Fan ◽  
Mingkun Luo ◽  
Sheng Li ◽  
Haohao Zhang ◽  
Zhenhua Yang ◽  
...  
Keyword(s):  
Coal Seam ◽  
Coalbed Methane ◽  
Coupled Model ◽  
Coupling Model ◽  
Gas Production ◽  
Methane Recovery ◽  
Acid Fracturing ◽  
Enhanced Coalbed Methane Recovery ◽  
Reservoir Permeability ◽  
Enhanced Coalbed Methane

The reservoir permeability dominates the transport of gas and water in coal seam. However, coal seams rich in gas usually contain various pores and fractures blocked by a large amount of minerals, which leads to an ultra-low permeability and gas extraction rate, and thus an increase of drilling workload. We first propose a thermo-hydro-mechanical-chemical coupled model (THMC) for the acid fracturing enhanced coalbed methane recovery (AF-ECBM). Then, this model is applied to simulate the variation of key parameters during AF-ECBM using a 2D geometry. The effect of different extraction schedules are comparatively analyzed to give an insight into these complex coupling responses in coal seam. Result confirms that the AF-ECBM is an effective way to increase the reservoir permeability and improve the gas production using the proposed model. The range of permeability increment zone increases most dramatically in the way of acid fracturing, followed by none-acid fracturing and acidizing over time. The gas production in order is: acid fracturing (AF-ECBM) > fracturing (F-ECBM) > acidification (A-ECBM)> direct extraction (D-CBM).

Quantification of Gas and Water Transfer Between Coal Matrix and Cleat Network During Drainage Process

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Mingjun Zou ◽  
Chongtao Wei ◽  
Miao Zhang ◽  
Xiaochun Lv
Keyword(s):  
Coalbed Methane ◽  
Gas Production ◽  
Water Transfer ◽  
Gas Transfer ◽  
Critical Porosity ◽  
Coal Matrix ◽  
Gas Desorption ◽  
Southern Qinshui Basin ◽  
Fluid Transfer

Mathematical models were developed in this study to quantify the gas and water transfer between coal matrix and cleat network during coalbed methane (CBM) drainage, which can be helpful to achieve some useful findings on features of fluid migration within coal reservoirs during drainage process. A typical CBM well located at southern Qinshui basin of China was selected as the case study. The ineffective critical porosity was defined and was used to acquire fluid transfer as a key parameter of the established model. Results showed that both the gas and water transfer controlled the drainage performances. Water drained from cleat was found to be the main reason for the decrease in the reservoir pressure at the early drainage stage, while the water transfer became significantly more important with the continuation of the drainage process. The first peak of gas production was controlled by gas desorption, and the subsequent peaks were influenced by the gas transfer.

Productivity Prediction of Coalbed Methane Considering the Permeability Changes in Coal

2014 ◽  
Author(s):  
H.. Chen ◽  
M.. Li ◽  
Y.. Zhang ◽  
C.. Liu ◽  
Y.. Li
Keyword(s):  
Numerical Model ◽  
Coalbed Methane ◽  
Field Data ◽  
Gas Production ◽  
Phase Flow ◽  
Two Phase ◽  
Gas Desorption ◽  
Permeability Changes ◽  
Cbm Production ◽  
Production Period

Abstract This paper describes a three-dimensional numerical model for predicting the coalbed methane (CBM) production. The model describes single phase gas desorption from coal matrix, diffusion to the fracture and two-phase flow of gas and water in the natural fracture system as well as the permeability changes in coal which result from effective stress changes and matrix shrinkage due to gas desorption. The model was discretized by a finite difference method. The implicit pressure-explicit saturation (IMPES) method was used to solve the two-phase flow equations and gas desorption equation was solved implicitly. The numerical model was validated by the field data from Qinshui basin in China. Based on the model, the impact of various reservoir and Langmuir isothermal adsorption parameters on the gas production was investigated. The results show that the gas production rate of the coalbed methane predicted by this model is in good accordance with the field data. The permeability near the wellbore dramatically decreases as the reservoir pressure drops at the early production period while at the later production period, the permeability near the wellbore increases because of the matrix shrinkage. The permeability changes far away from the wellbore are not so remarkable. In addition, the gas production rate increases with the increased permeability, seam thickness and Langmuir pressure constant while it decreases with the increased porosity and Langmuir volume constant. The numerical model can be used to predict and analyze the production performance of CBM reservoirs and the research results provide theoretical support for CBM production.

Sign in / Sign up

Export Citation Format

Share Document