scholarly journals Design and Energy Consumption Analysis of Small Reverse Osmosis Seawater Desalination Equipment

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2275
Author(s):  
Zhuo Wang ◽  
Yanjie Zhang ◽  
Tao Wang ◽  
Bo Zhang ◽  
Hongwen Ma
Keyword(s):  
Energy Consumption ◽  
Water Resources ◽  
Reverse Osmosis ◽  
Specific Energy Consumption ◽  
Membrane System ◽  
Energy Utilization ◽  
Utilization Efficiency ◽  
Small Scale ◽  
Reverse Osmosis Membrane ◽  
Seawater Desalination

The reverse osmosis method has developed extremely rapidly in recent years and has become the most competitive seawater desalination technology in the world, and it has been widely used in all aspects. Large-scale reverse osmosis desalination plants cannot provide fresh water resources in areas with insufficient water resources and limited space. Therefore, this paper proposes a research plan for a small seawater desalination device based on reverse osmosis, which is mainly suitable for handling emergencies, disaster relief, desert areas and outdoor activities and other needs for timely freshwater resources. It mainly includes pretreatment modules, a reaction infiltration module, a post-processing module and an energy supply module. Detailed design calculations are carried out for the small-scale reverse osmosis membrane system, including the selection and quantity and arrangement of membranes. Subsequently, the one-stage two-stage small-scale reverse osmosis membrane system was modeled, and its energy consumption was analyzed theoretically from the perspectives of specific energy consumption and energy utilization efficiency; the main influencing factors were clarified, and the optimal recovery rate for system operation was determined to be 20%–30%. Finally, an experimental prototype was built to conduct relevant experiments to determine the influence trend of pressure, temperature, concentration, and flow rate on the operating performance of the reverse osmosis system.

scholarly journals Use of the Life Cycle Methodology to Calculate Energy Consumption of Urban Water Cycle: A Case Study of Ordos City

Water ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 2393
Author(s):  
Luming Zhou ◽  
Xinghua Xie ◽  
Shiqiang Wu
Keyword(s):  
Life Cycle ◽  
Energy Consumption ◽  
Water Resources ◽  
Energy Demand ◽  
Water Cycle ◽  
Thermal Power ◽  
Sewage Treatment ◽  
Energy Utilization ◽  
Utilization Efficiency ◽  
Unit Energy

Water resources and energy constitute two broad categories of resources required for social and economic development. The water-energy nexus has become a focus of research in recent years. Although water resources are closely related to energy systems, the processes involved remain incompletely understood due to the diversity and complexity of energy types, processes, and consumption sectors. This study aimed to accurately calculate the energy demand of water resources and to identify an effective method of improving the energy utilization efficiency of water. The life cycle of water resources was divided into five stages based on the life cycle methodology: (1) extraction, (2) purification, (3) transportation, (4) utilization, (5) sewage treatment. The quantity and characteristics of energy consumed in each stage were studied, and an equation to calculate energy consumption for each stage was proposed. Using the city of Ordos in Northwest China as an example, energy consumption of water resources from 2013 to 2017 was analyzed. The results showed that from 2013 to 2017, energy consumption and per unit energy consumption of water resources in Ordos decreased by 33.3% and 30.6% from 1.62 × 108 kWh to 1.08 × 108 kWh and from 10.11 kWh·m−3 to 7.02 kWh·m−3, respectively. The majority of energy consumption over the entire life cycle of water resources occurred during the utilization stage at a proportion of total energy consumed of ~95%. Use of water for thermal power generation was identified as the single largest consumer of energy and, therefore, has the greatest potential for energy saving.

scholarly journals Batch Reverse Osmosis Desalination Modeling under a Time-Dependent Pressure Profile

Membranes ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 173
Author(s):  
Abdeljalil Chougradi ◽  
François Zaviska ◽  
Ahmed Abed ◽  
Jérôme Harmand ◽  
Jamal-Eddine Jellal ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Reverse Osmosis ◽  
Specific Energy ◽  
Energy Demand ◽  
Specific Energy Consumption ◽  
Pressure Profile ◽  
Recovery Ratio ◽  
Feed Concentration ◽  
Energetic Performance ◽  
Feed Volume

As world demand for clean water increases, reverse osmosis (RO) desalination has emerged as an attractive solution. Continuous RO is the most used desalination technology today. However, a new generation of configurations, working in unsteady-state feed concentration and pressure, have gained more attention recently, including the batch RO process. Our work presents a mathematical modeling for batch RO that offers the possibility of monitoring all variables of the process, including specific energy consumption, as a function of time and the recovery ratio. Validation is achieved by comparison with data from the experimental set-up and an existing model in the literature. Energetic comparison with continuous RO processes confirms that batch RO can be more energy efficient than can continuous RO, especially at a higher recovery ratio. It used, at recovery, 31% less energy for seawater and 19% less energy for brackish water. Modeling also proves that the batch RO process does not have to function under constant flux to deliver good energetic performance. In fact, under a linear pressure profile, batch RO can still deliver better energetic performance than can a continuous configuration. The parameters analysis shows that salinity, pump and energy recovery devices efficiencies are directly linked to the energy demand. While increasing feed volume has a limited effect after a certain volume due to dilution, it also shows, interestingly, a recovery ratio interval in which feed volume does not affect specific energy consumption.

scholarly journals Energetic and exergetic analysis of a convective drier: A case study of potato drying process

2020 ◽  
Vol 5 (1) ◽  
pp. 563-572
Author(s):  
Iman Golpour ◽  
Mohammad Kaveh ◽  
Reza Amiri Chayjan ◽  
Raquel P. F. Guiné
Keyword(s):  
Energy Consumption ◽  
Research Work ◽  
Specific Energy Consumption ◽  
Exergy Efficiency ◽  
Operating Conditions ◽  
Energy Utilization ◽  
Convective Drying ◽  
Drying Time ◽  
Energy And Exergy ◽  
Exergy Losses

AbstractThis research work focused on the evaluation of energy and exergy in the convective drying of potato slices. Experiments were conducted at four air temperatures (40, 50, 60 and 70°C) and three air velocities (0.5, 1.0 and 1.5 m/s) in a convective dryer, with circulating heated air. Freshly harvested potatoes with initial moisture content (MC) of 79.9% wet basis were used in this research. The influence of temperature and air velocity was investigated in terms of energy and exergy (energy utilization [EU], energy utilization ratio [EUR], exergy losses and exergy efficiency). The calculations for energy and exergy were based on the first and second laws of thermodynamics. Results indicated that EU, EUR and exergy losses decreased along drying time, while exergy efficiency increased. The specific energy consumption (SEC) varied from 1.94 × 105 to 3.14 × 105 kJ/kg. The exergy loss varied in the range of 0.006 to 0.036 kJ/s and the maximum exergy efficiency obtained was 85.85% at 70°C and 0.5 m/s, while minimum exergy efficiency was 57.07% at 40°C and 1.5 m/s. Moreover, the values of exergetic improvement potential (IP) rate changed between 0.0016 and 0.0046 kJ/s and the highest value occurred for drying at 70°C and 1.5 m/s, whereas the lowest value was for 70°C and 0.5 m/s. As a result, this knowledge will allow the optimization of convective dryers, when operating for the drying of this food product or others, as well as choosing the most appropriate operating conditions that cause the reduction of energy consumption, irreversibilities and losses in the industrial convective drying processes.

scholarly journals Analytical Investigation of a Novel System for Combined Dew Point Cooling and Water Recovery

2021 ◽  
Vol 11 (4) ◽  
pp. 1481
Author(s):  
Aleksandra Cichoń ◽  
William Worek
Keyword(s):  
Energy Consumption ◽  
Convective Heat Transfer Coefficient ◽  
Specific Energy Consumption ◽  
Analytical Investigation ◽  
Dew Point ◽  
Energy Utilization ◽  
Coefficient Of Performance ◽  
Air Cooling ◽  
Water Recovery ◽  
Utilization Factor

This paper presents the analytical investigation of a novel system for combined Dew Point Cooling and Water Recovery (DPC-WR system). The operating principle of the presented system is to utilize the dew point cooling phenomenon implemented in two stages in order to obtain both air cooling and water recovery. The system performance is described by different indicators, including the coefficient of performance (COP), gained output ratio (GOR), energy utilization factor (EUF), specific energy consumption (SEC) and specific daily water production (SDWP). The performance indicators are calculated for various climatic zones using a validated analytical model based on the convective heat transfer coefficient. By utilizing the dew point cooling phenomenon, it is possible to minimize the heat and electric energy consumption from external sources, which results in the COP and GOR values being an order of magnitude higher than for other cooling and water recovery technologies. The EUF value of the DPC-WR system ranges from 0.76 to 0.96, with an average of 0.90. The SEC value ranges from 0.5 to 2.0 kWh/m3 and the SDWP value ranges from 100 to 600 L/day/(kg/s). In addition, the DPC-WR system is modular, i.e., it can be multiplied as needed to achieve the required cooling or water recovery capacity.

scholarly journals Environmental Performance of Small-Scale Seawater Reverse Osmosis Plant for Rural Area Water Supply

Membranes ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 40
Author(s):  
Latifah Abdul Ghani ◽  
Nora’aini Ali ◽  
Ilyanni Syazira Nazaran ◽  
Marlia M. Hanafiah
Keyword(s):  
Drinking Water ◽  
Global Warming ◽  
Water Supply ◽  
Reverse Osmosis ◽  
Resource Scarcity ◽  
Small Scale ◽  
Seawater Desalination ◽  
Seawater Reverse Osmosis ◽  
Desalination Technology ◽  
The Impact

Seawater desalination is an alternative technology to provide safe drinking water and to solve water issues in an area having low water quality and limited drinking water supply. Currently, reverse osmosis (RO) is commonly used in the desalination technology and experiencing significant growth. The aim of this study was to analyze the environmental impacts of the seawater reverse osmosis (SWRO) plant installed in Kampung Pantai Senok, Kelantan, as this plant was the first installed in Malaysia. The software SimaPro 8.5 together with the ReCiPe 2016 database were used as tools to evaluate the life cycle assessment (LCA) of the SWRO plant. The results showed that the impact of global warming (3.90 kg CO2 eq/year) was the highest, followed by terrestrial ecotoxicity (1.62 kg 1,4-DCB/year) and fossil resource scarcity (1.29 kg oil eq/year). The impact of global warming was caused by the natural gas used to generate the electricity, mainly during the RO process. Reducing the environmental impact can be effectively achieved by decreasing the electricity usage for the seawater desalination process. As a suggestion, electricity generation can be overcome by using a high-flux membrane with other suitable renewable energy for the plant such as solar and wind energy.

Carbon Emission of Mining Industry’s Energy Consumption in Heilongjiang Province

2015 ◽  
Vol 1092-1093 ◽  
pp. 1597-1600
Author(s):  
Zhong Hua Wang ◽  
Xin Ye Chen
Keyword(s):  
Energy Consumption ◽  
Carbon Emissions ◽  
Carbon Emission ◽  
Industrial Structure ◽  
Mining Industry ◽  
Calculation Model ◽  
Energy Utilization ◽  
Utilization Efficiency ◽  
Heilongjiang Province ◽  
Low Carbon

The need to reduce carbon emission in Heilongjiang Province of China is urgent challenge facing sustainable development. This paper aims to make explicit the problem-solving of carbon emission to find low carbon emission ways. According to domestic and foreign literatures on estimating and calculating carbon emissions and by integrating calculation methods of carbon emissions, it was not possible to consider all of the many contributions to carbon emissions. Calculation model of carbon emissions suitable to this paper is selected. The carbon emissions of energy consumption in mining industry are estimated and calculated from 2005 to 2012, and the characteristics of carbon emission are analyzed at the provincial level. It makes the point that carbon emissions of energy consumption in mining industry can be reduced when we attempt to alter energy consumption structure, adjust industrial structure and improve energy utilization efficiency.

Simulation and Analysis of Cryogenic Air Separation Process with LNG Cold Energy Utilization

2014 ◽  
Vol 881-883 ◽  
pp. 653-658 ◽  
Author(s):  
Yong Qiang Xiong ◽  
Ben Hua
Keyword(s):  
Energy Consumption ◽  
Liquid Nitrogen ◽  
Electric Energy ◽  
Separation Process ◽  
Air Separation ◽  
Energy Utilization ◽  
Utilization Efficiency ◽  
Pure Oxygen ◽  
Pure Nitrogen ◽  
Cold Energy

In this paper, a cryogenic air separation process with LNG cold energy utilization is proposed to produce liquid nitrogen and high pressure pure oxygen gas economically. To reduce the electric energy consumption of air separation products, liquid nitrogen have been produced by condensing the separated pure nitrogen gas with LNG cold energy utilization, and the recycled nitrogen is served to transfer cold energy from LNG stream to cool off air stream in the proposed cryogenic air separation process. The specifications of streams and the major equipments of the air separation process are simulated with Aspen Plus software and the main parameters analysis are performed. The results show that the energy consumption of the proposed air separation process with LNG cold energy utilization decreased about 58.2% compared with a conventional cryogenic air separation process. The compressed pressure of recycled nitrogen has a big impact on the cost of air separation products and utilization efficiency of LNG cold energy. The LNG cold energy could be fully utilized when the recycled nitrogen has been compressed to above 6.5MPa.

Analysis of China’s Provincial Energy Efficiency Based on the Generalized DEA Method

2014 ◽  
Vol 953-954 ◽  
pp. 890-895
Author(s):  
Hui Min Li ◽  
Cun Bin Li ◽  
Zhan Xin Ma
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
Energy Utilization ◽  
Utilization Efficiency ◽  
Total Energy Consumption ◽  
Rapid Economic Growth ◽  
Technology Changes ◽  
Dea Method ◽  
Save Energy ◽  
The Impact

In recent years, with the rapid economic growth, the demand on the amount of energy in China is increasing. So the problem of how to improve the energy utilization efficiency and save energy consumption has to be tackled. The traditional CCR model and BCC model used in the study of provincial energy efficiency do not take the impact of technological progress into consideration. Therefore, the paper uses the generalized DEA method to research the energy utilization efficiency of China’s 29 provinces, that is, to evaluate and analyze the energy utilization efficiency by selecting the capital stock, employment and total energy consumption of China’s provinces as input factors and GDP, per capital GDP as output factors, and then draw tables showing each province’s change of average annual overall efficiency and the pure technology changes, and finally analyze the regularities underlying these changes.

Sign in / Sign up

Export Citation Format

Share Document