scholarly journals Fabrication of Polycaprolactone/Nano Hydroxyapatite (PCL/nHA) 3D Scaffold with Enhanced In Vitro Cell Response via Design for Additive Manufacturing (DfAM)

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1394
Author(s):  
Yong Sang Cho ◽  
So-Jung Gwak ◽  
Young-Sam Cho
Keyword(s):  
Mechanical Properties ◽  
Cell Response ◽  
Structural Characteristics ◽  
Structure Design ◽  
Compressive Modulus ◽  
Control Group ◽  
Design For Additive Manufacturing ◽  
3D Scaffold ◽  
3D Printed

In this study, we investigated the dual-pore kagome-structure design of a 3D-printed scaffold with enhanced in vitro cell response and compared the mechanical properties with 3D-printed scaffolds with conventional or offset patterns. The compressive modulus of the 3D-printed scaffold with the proposed design was found to resemble that of the 3D-printed scaffold with a conventional pattern at similar pore sizes despite higher porosity. Furthermore, the compressive modulus of the proposed scaffold surpassed that of the 3D-printed scaffold with conventional and offset patterns at similar porosities owing to the structural characteristics of the kagome structure. Regarding the in vitro cell response, cell adhesion, cell growth, and ALP concentration of the proposed scaffold for 14 days was superior to those of the control group scaffolds. Consequently, we found that the mechanical properties and in vitro cell response of the 3D-printed scaffold could be improved by kagome and dual-pore structures through DfAM. Moreover, we revealed that the dual-pore structure is effective for the in vitro cell response compared to the structures possessing conventional and offset patterns.

scholarly journals Evaluation of the Antibacterial Activity and Cell Response for 3D-Printed Polycaprolactone/Nanohydroxyapatite Scaffold with Zinc Oxide Coating

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2193
Author(s):  
Yong Sang Cho ◽  
Hee-Kyeong Kim ◽  
Min-Soo Ghim ◽  
Myoung Wha Hong ◽  
Young Yul Kim ◽  
...  
Keyword(s):  
Cell Proliferation ◽  
Zinc Oxide ◽  
Antibacterial Activity ◽  
Cell Response ◽  
Oxide Coating ◽  
Compressive Modulus ◽  
Bacterial Activity ◽  
Zinc Ions ◽  
3D Printed

Among 3D-printed composite scaffolds for bone tissue engineering, researchers have been attracted to the use of zinc ions to improve the scaffold’s anti-bacterial activity and prevent surgical site infection. In this study, we assumed that the concentration of zinc ions released from the scaffold will be correlated with the thickness of the zinc oxide coating on 3D-printed scaffolds. We investigated the adequate thickness of zinc oxide coating by comparing different scaffolds’ characteristics, antibacterial activity, and in vitro cell response. The scaffolds’ compressive modulus decreased as the zinc oxide coating thickness increased (10, 100 and 200 nm). However, the compressive modulus of scaffolds in this study were superior to those of other reported scaffolds because our scaffolds had a kagome structure and were made of composite material. In regard to the antibacterial activity and in vitro cell response, the in vitro cell proliferation on scaffolds with a zinc oxide coating was higher than that of the control scaffold. Moreover, the antibacterial activity of scaffolds with 100 or 200 nm-thick zinc oxide coating on Escherichia coli was superior to that of other scaffolds. Therefore, we concluded that the scaffold with a 100 nm-thick zinc oxide coating was the most appropriate scaffold to use as a bone-regenerating scaffold, given its mechanical property, its antibacterial activity, and its in vitro cell proliferation.

Enhanced mechanical properties and in vitro cell response of surface mechanical attrition treated pure titanium

2011 ◽  
Vol 27 (2) ◽  
pp. 113-118 ◽  
Author(s):  
Changli Zhao ◽  
Pei Han ◽  
Weiping Ji ◽  
Xiaonong Zhang
Keyword(s):  
Mechanical Properties ◽  
Cell Response ◽  
Pure Titanium ◽  
Mechanical Attrition

scholarly journals 3D Plotting using Camphene as Pore-regulating Agent to Produce Hierarchical Macro/micro-porous Poly(ε-caprolactone)/calcium phosphate Composite Scaffolds

Materials ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 2650
Author(s):  
Jae-Won Choi ◽  
Woo-Youl Maeng ◽  
Young-Hag Koh ◽  
Hyun Lee ◽  
Hyoun-Ee Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Phase Separation ◽  
Calcium Phosphate ◽  
Tensile Modulus ◽  
Compressive Modulus ◽  
Composite Scaffolds ◽  
In Vitro Biocompatibility ◽  
Porous Poly

This study demonstrates the utility of camphene as the pore-regulating agent for phase separation-based 3D plotting to produce hierarchical macro/micro-porous poly(ε-caprolactone) (PCL)–calcium phosphate (CaP) composite scaffolds, specifically featuring highly microporous surfaces. Unlike conventional particulate porogens, camphene is highly soluble in acetone, the solvent for PCL polymer, but insoluble in coagulation medium (water). In this study, this unique characteristic supported the creation of numerous micropores both within and at the surfaces of PCL and PCL–CaP composite filaments when using high camphene contents (40 and 50 wt%). In addition, the incorporation of the CaP particles into PCL solutions did not deteriorate the formation of microporous structures, and thus hierarchical macro/micro-porous PCL–CaP composite scaffolds could be successfully produced. As the CaP content increased, the in vitro biocompatibility, apatite-forming ability, and mechanical properties (tensile strength, tensile modulus, and compressive modulus) of the PCL–CaP composite scaffolds were substantially improved.

scholarly journals Radiopaque Chitosan Ducts Fabricated by Extrusion-Based 3D Printing to Promote Healing After Pancreaticoenterostomy

2021 ◽  
Vol 9 ◽  
Author(s):  
Maoen Pan ◽  
Chaoqian Zhao ◽  
Zeya Xu ◽  
Yuanyuan Yang ◽  
Tianhong Teng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Pancreatic Duct ◽  
Silicone Rubber ◽  
The Body ◽  
Molecular Weights ◽  
Pancreatic Duct Stent ◽  
3D Printed

Long-term placement of non-degradable silicone rubber pancreatic duct stents in the body is likely to cause inflammation and injury. Therefore, it is necessary to develop degradable and biocompatible stents to replace silicone rubber tubes as pancreatic duct stents. The purpose of our research was to verify the feasibility and biological safety of extrusion-based 3D printed radiopaque chitosan (CS) ducts for pancreaticojejunostomy. Chitosan-barium sulfate (CS-Ba) ducts with different molecular weights (low-, medium-, and high-molecular weight CS-Ba: LCS-Ba, MCS-Ba, and HCS-Ba, respectively) were soaked in vitro in simulated pancreatic juice (SPJ) (pH 8.0) with or without pancreatin for 16 weeks. Changes in their weight, water absorption rate and mechanical properties were tested regularly. The biocompatibility, degradation and radiopaque performance were verified by in vivo and in vitro experiments. The results showed that CS-Ba ducts prepared by this method had regular compact structures and good molding effects. In addition, the lower the molecular weight of the CS-Ba ducts was, the faster the degradation rate was. Extrusion-based 3D-printed CS-Ba ducts have mechanical properties that match those of soft tissue, good biocompatibility and radioopacity. In vitro studies have also shown that CS-Ba ducts can promote the growth of fibroblasts. These stents have great potential for use in pancreatic duct stent applications in the future.

scholarly journals Stability Assessment of Four Chimeric Proteins for Human Chagas Disease Immunodiagnosis

Biosensors ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 289
Author(s):  
Paola Alejandra Fiorani Celedon ◽  
Leonardo Maia Leony ◽  
Ueriton Dias Oliveira ◽  
Natália Erdens Maron Freitas ◽  
Ângelo Antônio Oliveira Silva ◽  
...  
Keyword(s):  
Chagas Disease ◽  
Structural Integrity ◽  
Structural Characteristics ◽  
Control Group ◽  
Stability Tests ◽  
Adverse Conditions ◽  
Term Stability ◽  
Long Term Stability

The performance of an immunoassay relies on antigen-antibody interaction; hence, antigen chemical stability and structural integrity are paramount for an efficient assay. We conducted a functional, thermostability and long-term stability analysis of different chimeric antigens (IBMP), in order to assess effects of adverse conditions on four antigens employed in ELISA to diagnose Chagas disease. ELISA-based immunoassays have served as a model for biosensors development, as both assess molecular interactions. To evaluate thermostability, samples were heated and cooled to verify heat-induced denaturation reversibility. In relation to storage stability, the antigens were analyzed at 25 °C at different moments. Long-term stability tests were performed using eight sets of microplates sensitized. Antigens were structurally analyzed through circular dichroism (CD), dynamic light scattering, SDS-PAGE, and functionally evaluated by ELISA. Data suggest that IBMP antigens are stable, over adverse conditions and for over a year. Daily analysis revealed minor changes in the molecular structure. Functionally, IBMP-8.2 and IBMP-8.3 antigens showed reactivity towards anti-T. cruzi antibodies, even after 72 h at 25 °C. Long-term stability tests showed that all antigens were comparable to the control group and all antigens demonstrated stability for one year. Data suggest that the antigens maintained their function and structural characteristics even in adverse conditions, making them a sturdy and reliable candidate to be employed in future in vitro diagnostic tests applicable to different models of POC devices, such as modern biosensors in development.

scholarly journals Additive Manufacturing of Bone Scaffolds Using PolyJet and Stereolithography Techniques

2021 ◽  
Vol 11 (16) ◽  
pp. 7336
Author(s):  
Shummaila Rasheed ◽  
Waqas Akbar Lughmani ◽  
Muhannad Ahmed Obeidi ◽  
Dermot Brabazon ◽  
Inam Ul Ahad
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Dimensional Accuracy ◽  
Human Bone ◽  
Compression Tests ◽  
3D Scaffold ◽  
Bone Scaffolds ◽  
3D Printed ◽  
Printing Direction ◽  
Printing Techniques

In this study, the printing capability of two different additive manufacturing (3D printing) techniques, namely PolyJet and micro-stereolithography (µSLA), are investigated regarding the fabrication of bone scaffolds. The 3D-printed scaffold structures are used as supports in replacing and repairing fractured bone tissue. Printed bone scaffolds with complex structures produced using additive manufacturing technology can mimic the mechanical properties of natural human bone, providing lightweight structures with modifiable porosity levels. In this study, 3D scaffold structures are designed with different combinations of architectural parameters. The dimensional accuracy, permeability, and mechanical properties of complex 3D-printed scaffold structures are analyzed to compare the advantages and drawbacks associated with the two techniques. The fluid flow rates through the 3D-printed scaffold structures are measured and Darcy’s law is applied to calculate the experimentally measured permeability. The Kozeny–Carman equation is applied for theoretical calculation of permeability. Compression tests were performed on the printed samples to observe the effects of the printing techniques on the mechanical properties of the 3D-printed scaffold structures. The effect of the printing direction on the mechanical properties of the 3D-printed scaffold structures is also analyzed. The scaffold structures printed with the µSLA printer demonstrate higher permeability and mechanical properties as compared to those printed using the PolyJet technique. It is demonstrated that both the µSLA and PolyJet printing techniques can be used to print 3D scaffold structures with controlled porosity levels, providing permeability in a similar range to human bone.

scholarly journals Effect of 5% Calcium Hypochlorite on Mechanical Properties of Root Dentin: An in vitro Study

2016 ◽  
Vol 1 (2) ◽  
pp. 56-59
Author(s):  
Natanasabapathy Velmurugan ◽  
Poornima Reddy ◽  
Suma Balla ◽  
Sandhya S Raghu ◽  
Garlapati T Gupta ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
In Vitro Study ◽  
Chlorine Concentration ◽  
Control Group ◽  
Calcium Hypochlorite ◽  
Significant Difference ◽  
Root Dentin

ABSTRACT Introduction The aim of this study was to compare in vitro the effect of 5% calcium hypochlorite [Ca(OCl)2] and 5% sodium hypochlorite (NaOCl) on flexural strength and modulus of elasticity of root dentin. Materials and methods The available chlorine concentration of each solution was determined using iodometric titration. Standardized planoparallel dentin bars (n= 20) were divided into two test groups and one control group. The control, group 1, consisted of dentin bars stored in normal saline. The dentin bars in the two test groups were treated by exposure to following solutions: Group 2 to 5% Ca(OCl)2; and group 3 to 5% NaOCl. All the three test solutions were changed once in 15 minutes for 30 minutes. The dentin bars were then loaded to failure using three-point bend test. Results Available chlorine concentration was 64% in both the test solutions. There was a significant reduction in the flexural strength of 5% NaOCl group compared to 5% Ca(OCl)2-treated ones. A significant difference in modulus of elasticity was observed between the test groups and the control groups and also between the 5% Ca(OCl)2 and 5% NaOCl groups. Conclusion Within the limitations of this study, 5% NaOCl reduced the flexural strength and modulus of elasticity of root dentin bars more when compared to 5% Ca(OCl)2. How to cite this article Reddy P, Balla S, Raghu SS, Velmurugan N, Gupta GT, Sahoo HS. Effect of 5% Calcium Hypochlorite on Mechanical Properties of Root Dentin: An in vitro Study. J Oper Dent Endod 2016;1(2):56-59.

Alterations of mechanical properties in canine basilar arteries after subarachnoid hemorrhage

1989 ◽  
Vol 71 (3) ◽  
pp. 430-436 ◽  
Author(s):  
Phyo Kim ◽  
Thoralf M. Sundt ◽  
Paul M. Vanhoutte
Keyword(s):  
Mechanical Properties ◽  
Subarachnoid Hemorrhage ◽  
Autologous Blood ◽  
Myogenic Tone ◽  
Control Group ◽  
Resting Tension ◽  
Length Contraction ◽  
Basilar Arteries ◽  
Chronic Vasospasm

✓ The purpose of this study was to examine the hypotheses that structural stiffening of the arterial wall contributes to chronic cerebral vasospasm, and that alteration in properties of smooth muscle takes place after subarachnoid hemorrhage (SAH). Subarachnoid hemorrhage and subsequent chronic vasospasm were induced in dogs by two cisternal injections of autologous blood (on Day 0 and Day 2). Vasospasm was confirmed by angiography performed on Day 0 and Day 7. Animals in the control group underwent angiography only. On Day 8, the mechanical properties of the basilar arteries were studied in vitro. Passive compliance, measured under total inhibition of spontaneous myogenic tone with diltiazem (10−4 M) plus papaverine (10−4 M) was smaller in the SAH group. The length-contraction curve was shifted to the left and the optimum length for maximum contraction (Lmax) was significantly shorter in the spastic blood vessels. The spontaneous myogenic tone was augmented in the SAH group, resulting in an increase in resting tension at each length. By contrast, the maximum contractions in response to KCl and uridine 5′-triphosphate were markedly reduced in the SAH group, without changes in sensitivity to these agents. These differences in mechanical properties were observed in rings both with and without endothelium. The results indicate that, in chronic vasospasm, stiffening of the noncontractile component of the vasculature takes place as well as alterations in the contractile component, both of which presumably contribute to the shift in resting length-tension relationship and length-contraction relationship of the artery. The decreased distensibility, the increase in resting tension, and the shortening of the Lmax all favor a smaller diameter of the artery after SAH, possibly contributing to vasospasm.

scholarly journals Fabrication and In Vitro Evaluation of 3D Printed Porous Polyetherimide Scaffolds for Bone Tissue Engineering

2019 ◽  
Vol 2019 ◽  
pp. 1-8 ◽  
Author(s):  
Xiongfeng Tang ◽  
Yanguo Qin ◽  
Xinyu Xu ◽  
Deming Guo ◽  
Wenli Ye ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Cell Proliferation ◽  
Cell Adhesion ◽  
3D Printing ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Porous Scaffold ◽  
3D Printed

For bone tissue engineering, the porous scaffold should provide a biocompatible environment for cell adhesion, proliferation, and differentiation and match the mechanical properties of native bone tissue. In this work, we fabricated porous polyetherimide (PEI) scaffolds using a three-dimensional (3D) printing system, and the pore size was set as 800 μm. The morphology of 3D PEI scaffolds was characterized by the scanning electron microscope. To investigate the mechanical properties of the 3D PEI scaffold, the compressive mechanical test was performed via an electronic universal testing system. For the in vitro cell experiment, bone marrow stromal cells (BMSCs) were cultured on the surface of the 3D PEI scaffold and PEI slice, and cytotoxicity, cell adhesion, and cell proliferation were detected to verify their biocompatibility. Besides, the alkaline phosphatase staining and Alizarin Red staining were performed on the BMSCs of different samples to evaluate the osteogenic differentiation. Through these studies, we found that the 3D PEI scaffold showed an interconnected porous structure, which was consistent with the design. The elastic modulus of the 3D PEI scaffold (941.33 ± 65.26 MPa) falls in the range of modulus for the native cancellous bone. Moreover, the cell proliferation and morphology on the 3D PEI scaffold were better than those on the PEI slice, which revealed that the porous scaffold has good biocompatibility and that no toxic substances were produced during the progress of high-temperature 3D printing. The osteogenic differentiation level of the 3D PEI scaffold and PEI slice was equal and ordinary. All of these results suggest the 3D printed PEI scaffold would be a potential strategy for bone tissue engineering.

An Experimental Investigation of the Effects of Gamma Radiation on 3D Printed ABS for In-Space Manufacturing Purposes

2016 ◽  
Author(s):  
Behzad Rankouhi ◽  
Fereidoon Delfanian ◽  
Robert McTaggart ◽  
Todd Letcher
Keyword(s):  
Mechanical Properties ◽  
Fused Deposition Modeling ◽  
Mechanical Performance ◽  
Space Station ◽  
Surface Hardness ◽  
Low Earth Orbit ◽  
Radiation Environment ◽  
Control Group ◽  
Fused Deposition ◽  
3D Printed

The following work is presented as a preliminary study on the effects of gamma irradiation on mechanical properties of Acrylonitrile Butadiene Styrene (ABS) as an in-space 3D printing feedstock to investigate the forthcoming possibilities of this technology for future space exploration missions. 3D printed testing samples were irradiated at different dosages from 1 to 1400 kGy (1 Gray (Gy) = 1 J/kg = 100 rad) using a Cobalt-60 gamma irradiator to simulate space radiation environment. Testing samples were manufactured using Fused Deposition Modeling (FDM) with a Makerbot Replicator 2x 3D printer. The correlation between the mechanical properties of irradiated samples and accumulated radiation dosage were evaluated by a series of tensile and flexural tests. Furthermore, Shore hardness tests were conducted to evaluate changes in surface hardness of irradiated parts. Finally, results were compared with a control group of samples. Findings showed a significant decrease in mechanical performance and noticeable changes in appearance of the parts with accumulated dosage of 1000 kGy and higher. However, for dosages below 10 kGy, samples showed no significant decrease in mechanical performance or change in appearance. These results were used to predict the life of a 3D printed part on board the International Space Station (ISS), on Low Earth Orbit (LEO) satellites, in deep space and long duration missions.

Sign in / Sign up

Export Citation Format

Share Document