scholarly journals Design and Analysis of Super Wideband Antenna for Microwave Applications

Sensors ◽  
2021 ◽  
Vol 21 (2) ◽  
pp. 477
Author(s):  
Warsha Balani ◽  
Mrinal Sarvagya ◽  
Ajit Samasgikar ◽  
Tanweer Ali ◽  
Pradeep Kumar
Keyword(s):  
Communication Systems ◽  
Equivalent Circuit Model ◽  
Wireless Communication Systems ◽  
Impedance Bandwidth ◽  
Frequency Range ◽  
Fractional Bandwidth ◽  
Wide Bandwidth ◽  
Wireless Applications ◽  
Frequency Constraint ◽  
Time Domain Characterization

In this article, a compact concentric structured monopole patch antenna for super wideband (SWB) application is proposed and investigated. The essential characteristics of the designed antenna are: (i) to attain super-wide bandwidth characteristics, the proposed antenna is emerged from a traditional circular monopole antenna and has obtained an impedance bandwidth of 38.9:1 (ii) another important characteristic of the presented antenna is its larger bandwidth dimension ratio (BDR) value of 6596 that is accomplished by augmenting the electrical length of the patch. The electrical dimension of the proposed antenna is 0.18λ×0.16λ (λ corresponds to the lower end operating frequency). The designed antenna achieves a frequency range from 1.22 to 47.5 GHz with a fractional bandwidth of 190% and exhibiting S11 < −10 dB in simulation. For validating the simulated outcomes, the antenna model is fabricated and measured. Good conformity is established between measured and simulated results. Measured frequency ranges from 1.25 to 40 GHz with a fractional bandwidth of 188%, BDR of 6523 and S11 < −10 dB. Even though the presented antenna operates properly over the frequency range from 1.22 to 47.5 GHz, the results of the experiment are measured till 40 GHz because of the high-frequency constraint of the existing Vector Network Analyzer (VNA). The designed SWB antenna has the benefit of good gain, concise dimension, and wide bandwidth above the formerly reported antenna structures. Simulated gain varies from 0.5 to 10.3 dBi and measured gain varies from 0.2 to 9.7 dBi. Frequency domain, as well as time-domain characterization, has been realized to guide the relevance of the proposed antenna in SWB wireless applications. Furthermore, an equivalent circuit model of the proposed antenna is developed, and the response of the circuit is obtained. The presented antenna can be employed in L, S, C, X, Ka, K, Ku, and Q band wireless communication systems.

scholarly journals Wideband Printed Wide-Slot Antenna with Fork-Shaped Stub

Electronics ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 347 ◽  
Author(s):  
Ke Li ◽  
Tao Dong ◽  
Zhenghuan Xia
Keyword(s):  
Wireless Communication ◽  
Communication Systems ◽  
Slot Antenna ◽  
Wireless Communication Systems ◽  
Impedance Bandwidth ◽  
Frequency Range ◽  
Slot Antennas ◽  
Resonance Technique ◽  
Operating Frequency Range ◽  
Measured Impedance

This paper presents a multiple-resonance technique that sought to achieve a wide bandwidth for printed wide-slot antennas with fork-shaped stubs. By properly appending an extra fork-shaped stub onto the main fork-shaped stub, the impedance bandwidth was able to be clearly broadened. To validate this technique, two designs where the extra stubs were added at different positions of the main stub were constructed. The measured impedance bandwidths of the proposed antennas reached 148.6% (0.9–6.1 GHz) for S11 < −10 dB, indicating a 17.9% wider bandwidth than that of the normal antenna (0.9–4.3 GHz). Moreover, a stable radiation pattern was observed within the operating frequency range. The proposed antennas were confirmed to be much-improved candidates for applications in various wireless communication systems.

scholarly journals A Low-Profile Wideband Monocone Antenna Using Bent Shorting Strips

2019 ◽  
Vol 9 (9) ◽  
pp. 1896 ◽  
Author(s):  
Kyo-Seung Keum ◽  
Young-Mi Park ◽  
Jae-Hoon Choi
Keyword(s):  
Reflection Coefficient ◽  
Wireless Communication ◽  
Communication Systems ◽  
Ground Plane ◽  
Experimental Results ◽  
Wireless Communication Systems ◽  
Impedance Bandwidth ◽  
Wide Bandwidth ◽  
Low Profile ◽  
Radiation Properties

A low-profile wideband monocone antenna with bent shorting strips, and parasitic and circular sleeves is proposed. By loading the bent shorting strips, parasitic sleeves, and circular sleeves, miniaturization of the antenna is achieved. Along with bent shorting strips from the monocone hat to the ground plane, parasitic sleeves, and circular sleeves are mounted to enhance the impedance bandwidth. From the experimental results, the –10 dB reflection coefficient bandwidth of the proposed antenna ranges from 810 MHz to 5340 MHz. In addition to the wide bandwidth characteristics, the proposed antenna has highly desirable omnidirectional radiation properties for wireless communication systems.

scholarly journals Circularly Polarized Broadband Printed Antenna for Wireless Applications

Sensors ◽  
2018 ◽  
Vol 18 (12) ◽  
pp. 4261 ◽  
Author(s):  
Md. Samsuzzaman ◽  
Mohammad Islam
Keyword(s):  
Wireless Communication ◽  
Communication Systems ◽  
Ground Plane ◽  
Axial Ratio ◽  
Wireless Communication Systems ◽  
Impedance Bandwidth ◽  
Printed Antenna ◽  
Circularly Polarized ◽  
Wireless Applications ◽  
Design Structure

A simple, compact sickle-shaped printed antenna with a slotted ground plane is designed and developed for broadband circularly polarized (CP) radiation. The sickle-shaped radiator with a tapered feed line and circular slotted square ground plane are utilized to realize the wideband CP radiation feature. With optimized dimensions of 0.29λ × 0.29λ × 0.012λ at 2.22 GHz frequency for the realized antenna parameters, the measured results display that the antenna has a 10 dB impedance bandwidth of 7.70 GHz (126.85%; 2.22–9.92 GHz) and a 3 dB axial ratio (AR) bandwidth of 2.64 GHz (73.33%; 2.28–4.92 GHz). The measurement agrees well with simulation, which proves an excellent circularly polarized property. For verification, the mechanism of band improvement and circular polarization are presented, and the parametric study is carried out. Since, the proposed antenna is a simple design structure with broad impedance and AR bandwidth, which is a desirable feature as a candidate for various wireless communication systems. Because of the easy printed structure and scaling the dimension with broadband CP characteristics, the realized antenna does incorporate in a number of CP wireless communication applications.

scholarly journals Designing a Microstrip coupled line bandpass filter

2013 ◽  
Vol 2 (4) ◽  
pp. 266 ◽  
Author(s):  
Taoufik Ragani ◽  
N. Amar Touhami ◽  
M. Agoutane
Keyword(s):  
Wireless Communication ◽  
Significant Role ◽  
Communication Systems ◽  
Bandpass Filter ◽  
Bandpass Filters ◽  
Center Frequency ◽  
Wireless Communication Systems ◽  
Frequency Range ◽  
Wide Bandwidth ◽  
Coupled Line

Bandpass filters play a significant role in wireless communication systems. Transmitted and received signals have to be filtered at a certain center frequency with a specific bandwidth, in this paper, a coupled-line bandpass Filter at the center frequency 6 GHz with the wide bandwidth of 2 GHz. this type of filter can be used in WLAN and other applications for the frequency range of 5-7 GHz.

scholarly journals Propagation Channel Measurements in the mm- and Sub-mm Wave Range for Different Indoor Communication Scenarios

2021 ◽  
Vol 42 (4) ◽  
pp. 357-370
Author(s):  
M. A. Salhi ◽  
T. Kleine-Ostmann ◽  
T. Schrader
Keyword(s):  
Wireless Communication ◽  
Communication Systems ◽  
Wireless Communication Systems ◽  
Electromagnetic Spectrum ◽  
Channel Measurements ◽  
Frequency Range ◽  
Propagation Channel ◽  
Data Rates ◽  
Indoor Wireless ◽  
Wave Range

AbstractIncreasing data rates in wireless communications are accompanied with the need for new unoccupied and unregulated bandwidth in the electromagnetic spectrum. Higher carrier frequencies in the lower THz frequency range might offer the solution for future indoor wireless communication systems with data rates of 100 Gbit/s and beyond that cannot be located elsewhere. In this review, we discuss propagation channel measurements in an extremely broad frequency range from 50 to 325 GHz in selected indoor communication scenarios including kiosk downloading, office room communication, living rooms, and typical industrial environments.

scholarly journals Band notched self complementaryultra wideband antenna for wireless applications

2018 ◽  
Vol 7 (2.8) ◽  
pp. 529 ◽  
Author(s):  
Ch Ramakrishna ◽  
G A.E.Satish Kumar ◽  
P Chandra Sekhar Reddy
Keyword(s):  
High Frequency ◽  
Return Loss ◽  
Wide Band ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Relative Dielectric Permittivity ◽  
Frequency Range ◽  
Ground Structure ◽  
Wireless Applications ◽  
Patch Edge

This paper presents a band notched WLAN self complementaryultra wide band antenna for wireless applications. The proposed antenna encounters a return loss (RL) less than -10dB for entire ultra wideband frequency range except band notched frequency. This paper proposes a hexagon shape patch, edge feeding, self complementary technique and defective ground structure. The antenna has an overall dimensionof 28.3mm × 40mm × 2mm, builton  substrate FR4 with a relative dielectric permittivity 4.4. And framework is simulated finite element method with help of high frequency structured simulator HFSSv17.2.the proposed antenna achieves a impedance bandwidth of 8.6GHz,  band rejected WLAN frequency range 5.6-6.5 GHz with  vswr is less than 2.

Methods for improving the accuracy of frequency shift estimation in 5G NR

2021 ◽  
Author(s):  
Vladimir Sergeevich Milyutin ◽  
Eugeniy Vasilevich Rogozhnikov ◽  
Kirill Petrovskiy ◽  
Dmitriy Pokamestov ◽  
Edgar Dmitriyev ◽  
...  
Keyword(s):  
Frequency Shift ◽  
High Frequency ◽  
Communication Systems ◽  
Wide Frequency Range ◽  
Wireless Communication Systems ◽  
Frequency Synchronization ◽  
Frequency Range ◽  
Transmission Rates ◽  
Synchronization Accuracy ◽  
High Order Modulation

Abstract Frequency synchronization is a necessary operation for all wireless communication systems. Due to the wide frequency range defined for 5G NR systems, this procedure becomes critical. To ensure high transmission rates and the use of high-order modulation, up to 256 QAM for 5G communication systems, it is necessary to ensure high frequency synchronization accuracy. In this article, we have reviewed various approaches to implementing frequency synchronization and proposed, in our opinion, the most effective method for correcting the frequency shift of the signal.

scholarly journals Pattern Reconfigurable Antenna for VANET, Wi-Fi, and WiMAX Wireless Communication Systems

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Rahmani Faouzi ◽  
Amar Touhami Naima ◽  
BelbachirKchairi Abdelmounaim ◽  
Aknin Noura ◽  
Taher Nihade
Keyword(s):  
Wireless Communication ◽  
Communication Systems ◽  
Equivalent Circuit Model ◽  
Coaxial Cable ◽  
Wireless Communication Systems ◽  
Reconfigurable Antenna ◽  
Antenna Characteristic ◽  
Beam Switching ◽  
Theoretical Results ◽  
Good Agreement

This work presents the design and analysis of a beam switching antenna for VANET, Wi-Fi, and WiMAX wireless communication systems. The proposed reconfigurable antenna is powered by a coaxial cable and consists of a circular patch, six fish-shaped radiating elements, and a circular planar ground. The antenna was constructed on a Rogers RT5880 substrate. Its dimensions are as follows: 0.81λ0 × 0.81λ0 × 0.03λ0. It performs six reconfigurable operating states, at the same frequency, by controlling the activation and deactivation of six PIN diodes to change the beam’s direction. A theoretical equivalent circuit model of the antenna is extracted. A progressive analysis of improving the antenna characteristic performances is provided. The bandwidth of the proposed antenna is 9.07% (measured), 9.62% (simulated), and 9.31% (theoretical). The designed antenna has a maximum gain of 9.57 dB for all pattern states and a superior efficiency ratio from 85% to 95% over the operating range (5.54 GHz–6.10 GHz). The proposed reconfigurable antenna is fabricated. Measured, simulated, and theoretical results are given and show good agreement, including reflection coefficient (S11) and radiation patterns.

Development of Wireless Communication Systems in the Subterahertz Frequency Range

2019 ◽  
Vol 61 (10) ◽  
pp. 763-772
Author(s):  
V. V. Biryukov ◽  
V. L. Vaks ◽  
K. I. Kisilenko ◽  
A. N. Panin ◽  
S. I. Pripolzin ◽  
...  
Keyword(s):  
Wireless Communication ◽  
Communication Systems ◽  
Wireless Communication Systems ◽  
Frequency Range
Sign in / Sign up

Export Citation Format

Share Document