scholarly journals Study on the Adhesive Force of Powder Coating Layer (II)

1979 ◽  
Vol 52 (4) ◽  
pp. 174-178
Author(s):  
Go KIKUCHI ◽  
Teruo TSUNODA
Keyword(s):  
Coating Layer ◽  
Powder Coating ◽  
Adhesive Force

scholarly journals Development of adhesion force evaluation equipment for nano diamond coated tool using shear method

2020 ◽  
pp. 002029402097789
Author(s):  
Jinghua Li ◽  
SoJin Lee ◽  
HyunKyu Kweon
Keyword(s):  
Evaluation System ◽  
Evaluation Method ◽  
Adhesion Force ◽  
Coating Layer ◽  
Low Cost ◽  
High Surface ◽  
Surface Hardness ◽  
Adhesive Force ◽  
Diamond Coating ◽  
Acceleration Sensors

In this study, we have developed a thin film adhesion evaluation system for diamond coating tool, which is mainly used for CFRP processing. CFRP is widely used in aviation and automobile industries. Because of the high surface hardness of the diamond coating tool, it is difficult to evaluate the adhesive strength of the tool, and it is difficult to quantitatively evaluate the existing adhesion force evaluation method and it is costly. This study has developed an evaluation method to measure the adhesive force based on the data of the grinding process using a low-cost polishing pad. When the frictional force and the shearing force are applied to the specimen by the sanding belt, friction is continuously generated between the coating layer and the belt, and peeling occurs at the moment when a specific load is applied. Acceleration, load, and torque values that occur during each experiment are collected through acceleration sensors, load cells, and torque sensors. The data obtained through the experiments are subjected to FFT processing and analysis. As a result, the peeling point and the critical load value at this point are identified and referred to as the adhesion force of the coating layer.

A method for measuring the in-plane compressive strength and the compression behavior of coating layers

TAPPI Journal ◽  
2011 ◽  
Vol 10 (7) ◽  
pp. 29-34
Author(s):  
TEEMU PUHAKKA ◽  
ISKO KAJANTO ◽  
NINA PYKÄLÄINEN
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Calcium Carbonate ◽  
Coating Layer ◽  
Test Methods ◽  
Coating Films ◽  
Precipitated Calcium Carbonate ◽  
Coating Color ◽  
Mineral Coatings ◽  
Styrene Butadiene

Cracking at the fold is a quality defect sometimes observed in coated paper and board. Although tensile and compressive stresses occur during folding, test methods to measure the compressive strength of a coating have not been available. Our objective was to develop a method to measure the compressive strength of a coating layer and to investigate how different mineral coatings behave under compression. We used the short-span compressive strength test (SCT) to measure the in-plane compressive strength of a free coating layer. Unsupported free coating films were prepared for the measurements. Results indicate that the SCT method was suitable for measuring the in-plane compressive strength of a coating layer. Coating color formulations containing different kaolin and calcium carbonate minerals were used to study the effect of pigment particles’ shape on the compressive and tensile strengths of coatings. Latices having two different glass transition temperatures were used. Results showed that pigment particle shape influenced the strength of a coating layer. Platy clay gave better strength than spherical or needle-shaped carbonate pigments. Compressive and tensile strength decreased as a function of the amount of calcium carbonate in the coating color, particularly with precipitated calcium carbonate. We also assessed the influence of styrene-butadiene binder on the compressive strength of the coating layer, which increased with the binder level. The compressive strength of the coating layer was about three times the tensile strength.

Nanorobots Sense Local Physiochemical Heterogeneities of Tumor Matrisome

2020 ◽  
Author(s):  
Debayan Dasgupta ◽  
Dharma Pally ◽  
Deepak K. Saini ◽  
Ramray Bhat ◽  
Ambarish Ghosh
Keyword(s):  
Cell Lines ◽  
Cancer Cell ◽  
Cancer Cell Lines ◽  
Adhesive Force ◽  
Surrounding Tissue ◽  
Quantitative Measurements ◽  
Malignant Breast Tumor ◽  
Malignant Breast ◽  
Cancer Dissemination

The dissemination of cancer is brought about by continuous interaction of malignant cells with their surrounding tissue microenvironment. Understanding and quantifying the remodeling of local extracellular matrix (ECM) by invading cells can therefore provide fundamental insights into the dynamics of cancer dissemination. In this paper, we use an active and untethered nanomechanical tool, realized as magnetically driven nanorobots, to locally probe a 3D tissue culture microenvironment consisting of cancerous and non-cancerous epithelia, embedded within reconstituted basement membrane (rBM) matrix. Our assay is designed to mimic the in vivo histopathological milieu of a malignant breast tumor. We find that nanorobots preferentially adhere to the ECM near cancer cells: this is due to the distinct charge conditions of the cancer-remodeled ECM. Surprisingly, quantitative measurements estimate that the adhesive force increases with the metastatic ability of cancer cell lines, while the spatial extent of the remodeled ECM was measured to be approximately 40 μm for all cancer cell lines studied here. We hypothesized and experimentally confirmed that specific sialic acid linkages specific to cancer-secreted ECM may be a major contributing factor in determining this adhesive behavior. The findings reported here can lead to promising applications in cancer diagnosis, quantification of cancer aggression, in vivo drug delivery applications, and establishes the tremendous potential of magnetic nanorobots for fundamental studies of cancer biomechanics.

Impact of high temperature and soft nip calendering on the pore structure of the coating layer

2002 ◽  
Vol 17 (2) ◽  
pp. 147-152 ◽  
Author(s):  
Magnus Wikström ◽  
Mikael Bouveng ◽  
Mikael Rigdahl ◽  
Anthony G. Hiorns
Keyword(s):  
High Temperature ◽  
Pore Structure ◽  
Coating Layer
Sign in / Sign up

Export Citation Format

Share Document