Study of Raman Spectrum of Fe Doped CeO2 Thin Films Grown by Pulsed Laser Deposition

2010 ◽  
Vol 123-125 ◽  
pp. 375-378 ◽  
Author(s):  
Ram Prakash ◽  
Shalendra Kumar ◽  
Chan Gyu Lee ◽  
S.K. Sharma ◽  
Marcelo Knobel ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Single Phase ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Fe Doping ◽  
Full Width ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
X Ray

Ce1-xFexO2 (x=0, 0.01, 0.03 and 0.0 5) thin films were grown by pulsed laser deposition technique on Si and LaAlO3 (LAO) substrates. These films were deposited in vacuum and 200 mTorr oxygen partial pressure for both the substrates. These films were characterized by x-ray diffraction XRD and Raman spectroscopy measurements. XRD results reveal that these films are single phase. Raman results show F2g mode at ~466 cm-1 and defect peak at 489 cm-1 for film that deposited on LAO substrates, full width at half maximum (FWHM) is increasing with Fe doping for films deposited on both the substrates.

CRYSTALLINE SrTiO3 THIN FILMS ON SILICON BY PULSED LASER DEPOSITION

2005 ◽  
Vol 19 (01n03) ◽  
pp. 533-535
Author(s):  
J. H. HAO ◽  
J. GAO
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Perovskite Oxide ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
Rocking Curve ◽  
X Ray ◽  
Silicon Materials

We have developed a process to grow SrTiO 3 ( STO ) thin films showing single (110) orientation directly on Si by means of pulsed laser deposition technique. The growth of STO films directly on Si has been described. The crystallinity of the grown STO films was characterized by X-ray diffraction analysis of θ-2θ scan and rocking curve. Our results may be of interest for better understanding of the growth based on the perovskite oxide thin films on silicon materials.

Preparation and microstructural characterization of Si(100) Ce1−x GdxO2−δ thin films prepared by pulsed laser deposition technique

2014 ◽  
Vol 32 (4) ◽  
pp. 541-546 ◽  
Author(s):  
P. Nagaraju ◽  
Y. Vijayakumar ◽  
D. Phase ◽  
V. Reddy ◽  
M. Ramana Reddy
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Microstructural Characterization ◽  
Laser Deposition ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Krf Excimer Laser

AbstractMicrostructural properties of Ce1-x GdxO2-δ (x = 0 to 0.3) thin films prepared by pulsed laser deposition technique were studied. The thin films were deposited on Si(100) substrate at a substrate temperature of 973 K at the oxygen partial pressure of 0.2 Pa using KrF excimer laser with energy of 220 mJ. The prepared thin films were characterized by X-ray diffraction, Raman spectroscopy and atomic force microscopy. X-ray diffraction analysis confirmed the polycrystalline nature of the thin films. Crystallite size, strain and dislocation density were calculated. The Raman studies revealed the formation of Ce-O with the systematic variation of peak intensity and full width half maxima depending on concentration of gadolinium dopant. The thickness of the films was estimated using Talystep profiler. The surface roughness was estiamted based on AFM.

Synchrotron X-ray Diffraction Study of Single-Phase β-AlN Thin Films Heteroepitaxially Grown on Sapphire (0001) Substrates by Pulsed Laser Deposition

2010 ◽  
Vol 49 (2) ◽  
pp. 020212 ◽  
Author(s):  
Kazushi Sumitani ◽  
Ryota Ohtani ◽  
Tomohiro Yoshida ◽  
You Nakagawa ◽  
Satoshi Mohri ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Diffraction Study ◽  
Single Phase ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
X Ray

Epitaxial Pd-Doped LaFeO3 Films Grown on (100) SrTiO3 by Pulsed Laser Deposition

2014 ◽  
Vol 936 ◽  
pp. 282-286
Author(s):  
Ying Wen Duan
Keyword(s):  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Film Surface ◽  
Laser Deposition ◽  
Structural Quality ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
Orientation Relationships ◽  
X Ray ◽  
Transmission Electron

Single-crystalline, epitaxial LaFeO3 films with 5 at. % substitution of Pd on the Fe site are grown on (100) SrTiO3 substrate by pulsed-laser deposition technique. The epitaxial orientation relationships are (110)[001]LFPO||(100)[001]STO. X-ray diffraction and transmission electron microscopy reveal that the LFPO films have high structural quality and an atomically sharp LFPO/STO interface. After reduction treatments of as-grown LFPO films, very little Pd escaped the LFPO lattice onto the film surface, the formed Pd (100) particles are oriented epitaxially, and parallel to the LFPO films surface.

Growth of CaFeOX/LaFeO3 Superlattice on SrTiO3(100) Substrates

2011 ◽  
Vol 1292 ◽  
Author(s):  
Nobuyuki Iwata ◽  
Mark Huijben ◽  
Guus Rijnders ◽  
Hiroshi Yamamoto ◽  
Dave H. A. Blank
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Layer Growth ◽  
Laser Deposition ◽  
Growth Mode ◽  
Layer By Layer ◽  
X Ray Diffraction ◽  
Reciprocal Space Mapping ◽  
X Ray

ABSTRACTThe CaFeOX(CFO) and LaFeO3(LFO) thin films as well as superlattices were fabricated on SrTiO3(100) substrates by pulsed laser deposition (PLD) method. The tetragonal LFO film grew with layer-by-layer growth mode until approximately 40 layers. In the case of CFO, initial three layers showed layer-by-layer growth, and afterward the growth mode was transferred to two layers-by-two layers (TLTL) growth mode. The RHEED oscillation was observed until the end of the growth, approximately 50nm. Orthorhombic twin CaFeO2.5 (CFO2.5) structure was obtained. However, it is expected that the initial three CFO layers are CaFeO3 (CFO3) with the valence of Fe4+. The CFO and LFO superlattice showed a step-terraces surface, and the superlattice satellite peaks in a 2θ-θ and reciprocal space mapping (RSM) x-ray diffraction (XRD) measurements, indicating that the clear interfaces were fabricated.

High temperature x-ray diffraction studies of zirconia thin films prepared by reactive pulsed laser deposition

2011 ◽  
Vol 47 (4) ◽  
pp. 415-422 ◽  
Author(s):  
G. Balakrishnan ◽  
P. Kuppusami ◽  
S. Murugesan ◽  
E. Mohandas ◽  
D. Sastikumar
Keyword(s):  
Thin Films ◽  
High Temperature ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
X Ray

scholarly journals Lead potassium niobate thin films grown by Pulsed Laser Deposition

2016 ◽  
Vol vol1 (1) ◽  
Author(s):  
Billal Allouche ◽  
Yaovi Gagou ◽  
M. El Marssi
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Potassium Niobate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Deposition Parameters ◽  
Out Of Plane

By pulsed laser deposition, lead potassium niobate Pb2KNb5O15 was grown on (001) oriented Gd3Ga5O12 substrate using a platinum buffer layer. The PKN thin films were characterized by X-Ray diffraction and Scanning Electron Microscopy (SEM). The dependence of their structural properties as a function of the deposition parameters was studied. It has been found that the out of plane orientation of PKN film depends on the oxygen pressure used during the growth. Indeed, PKN thin film is oriented [001] for low pressure and is oriented [530] for high pressure. For these two orientations, the crystalline quality of PKN film was determined using omega scans.

ZrC Thin Films Grown by Pulsed Laser Deposition

2003 ◽  
Vol 780 ◽  
Author(s):  
V. Craciun ◽  
D. Craciun ◽  
J. M. Howard ◽  
R. K. Singh
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Photoelectron Spectroscopy ◽  
Pulsed Laser ◽  
Surface Region ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Si Substrates ◽  
Crystalline Films

AbstractZrC thin films were grown on Si substrates by the pulsed laser deposition (PLD) technique. X- ray photoelectron spectroscopy, x-ray diffraction and reflectivity, variable angle spectroscopic ellipsometry, and four point probe measurements were used to investigate the composition, density, thickness, surface morphology, optical and electrical properties of the grown structures. It has been found that crystalline films could be grown only by using fluences above 6 J/cm2 and substrate temperatures in excess of 500 °C. For a fluence of 10 J/cm2 and a substrate temperature of 700 °C, highly (100)-textured ZrC films exhibiting a cubic structure (a=0.469 nm) and a density of 6.7 g/cm3 were deposited. The use of a low-pressure atmosphere of C2H2 had a beneficial effect on crystallinity and stoichiometry of the films. All films contained high levels of oxygen contamination, especially in the surface region, because of the rather reactive nature of Zr atoms.

The effect of target crystallography on the growth of Pb(Mg1/3Nb2/3)O3 thin films using pulsed laser deposition

1999 ◽  
Vol 14 (6) ◽  
pp. 2355-2358 ◽  
Author(s):  
M. H. Corbett ◽  
G. Catalan ◽  
R. M. Bowman ◽  
J. M. Gregg
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Growth Conditions ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
Plan View ◽  
X Ray ◽  
Transmission Electron ◽  
Lead Magnesium

Pulsed laser deposition has been used to make two sets of lead magnesium niobate thin films grown on single-crystal h100j MgO substrates. One set was fabricated using a perovskite-rich target while the other used a pyrochlore-rich target. It was found that the growth conditions required to produce almost 100% perovskite Pb(Mg1/3Nb2/3)O3 (PMN) films were largely independent of target crystallography. Films were characterized crystallographically using x-ray diffraction and plan view transmission electron microscopy, chemically using energy dispersive x-ray analysis, and electrically by fabricating a planar thin film capacitor structure and monitoring capacitance as a function of temperature. All characterization techniques indicated that perovskite PMN thin films had been successfully fabricated.

Sign in / Sign up

Export Citation Format

Share Document