Fuel Injection Strategy for Clean Diesel Engine Using Ethanol Blended Diesel Fuel

2005 ◽  
Author(s):  
Ali Mohammadi ◽  
Takuji Ishiyama ◽  
Takaaki Kakuta ◽  
Sung-Sub Kee
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Strategy ◽  
Clean Diesel

A phenomenological combustion analysis of a dual-fuel natural-gas diesel engine

2016 ◽  
Vol 231 (1) ◽  
pp. 66-83 ◽  
Author(s):  
Shuonan Xu ◽  
David Anderson ◽  
Mark Hoffman ◽  
Robert Prucka ◽  
Zoran Filipi
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Heat Release ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Heavy Duty ◽  
Engine System ◽  
Wiebe Function

Energy security concerns and an abundant supply of natural gas in the USA provide the impetus for engine designers to consider alternative gaseous fuels in the existing engines. The dual-fuel natural-gas diesel engine concept is attractive because of the minimal design changes, the ability to preserve a high compression ratio of the baseline diesel, and the lack of range anxiety. However, the increased complexity of a dual-fuel engine poses challenges, including the knock limit at a high load, the combustion instability at a low load, and the transient response of an engine with directly injected diesel fuel and port fuel injection of compressed natural gas upstream of the intake manifold. Predictive simulations of the complete engine system are an invaluable tool for investigations of these conditions and development of dual-fuel control strategies. This paper presents the development of a phenomenological combustion model of a heavy-duty dual-fuel engine, aided by insights from experimental data. Heat release analysis is carried out first, using the cylinder pressure data acquired with both diesel-only and dual-fuel (diesel and natural gas) combustion over a wide operating range. A diesel injection timing correlation based on the injector solenoid valve pulse widths is developed, enabling the diesel fuel start of injection to be detected without extra sensors on the fuel injection cam. The experimental heat release trends are obtained with a hybrid triple-Wiebe function for both diesel-only operation and dual-fuel operation. The ignition delay period of dual-fuel operation is examined and estimated with a predictive correlation using the concept of a pseudo-diesel equivalence ratio. A four-stage combustion mechanism is discussed, and it is shown that a triple-Wiebe function has the ability to represent all stages of dual-fuel combustion. This creates a critical building block for modeling a heavy-duty dual-fuel turbocharged engine system.

Characteristics of injection of diesel fuel, rapeseed oil and their mixtures in diesel engines of various types

2021 ◽  
pp. 167-178
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Rapeseed Oil ◽  
High Speed ◽  
Fuel Injection ◽  
Experimental Studies ◽  
Fuel Injector ◽  
High Speed Diesel ◽  
Engine Type

The necessity of adapting diesel engines to work on vegetable oils is justified. The possibility of using rapeseed oil and its mixtures with petroleum diesel fuel as motor fuels is considered. Experimental studies of fuel injection of small high-speed diesel engine type MD-6 (1 Ch 8,0/7,5)when using diesel oil and rapeseed oil and computational studies of auto-tractor diesel engine type D-245.12 (1 ChN 11/12,5), working on blends of petroleum diesel fuel and rapeseed oil. When switching autotractor diesel engine from diesel fuel to rapeseed oil in the full-fuel mode, the mass cycle fuel supply increased by 12 %, and in the small-size high-speed diesel engine – by about 27 %. From the point of view of the flow of the working process of these diesel engines, changes in other parameters of the fuel injection process are less significant. Keywords diesel engine; petroleum diesel fuel; vegetable oil; rapeseed oil; high pressure fuel pump; fuel injector; sprayer

Effect of Fuel Injection Strategy on DPF Regeneration in Single Cylinder Diesel Engine

2015 ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Experimental Results ◽  
Exhaust Gas ◽  
Post Injection ◽  
Gas Temperature ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) force automotive manufacturers to equip DPF (diesel particulate filter) on diesel cars. Generally, post injection is used as a method to regenerate DPF. However, it is known that post injection deteriorates specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration becomes one of key technologies for diesel powertrain equipped with a DPF. This paper presents correlations between fuel injection strategy and exhaust gas temperature for DPF regeneration. Experimental apparatus consists of a single cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, post injection timing covers from 40 deg aTDC to 110 deg aTDC and double post injection was considered. In addition, effects of injection pressures were investigated. The engine load was varied from low-load to mid-load and fuel amount of post injection was increased up to 10mg/stk. Oil dilution during fuel injection and combustion processes were estimated by diesel loss measured by comparing two global equivalences ratios; one is measured from Lambda sensor installed at exhaust port, the other one is estimated from intake air mass and injected fuel mass. In the present study, the differences in global equivalence ratios were mainly caused from oil dilution during post injection. The experimental results of the present study suggest an optimal engine operating conditions including fuel injection strategy to get appropriate exhaust gas temperature for DPF regeneration. Experimental results of exhaust gas temperature distributions for various engine operating conditions were summarized. In addition, it was revealed that amounts of oil dilution were reduced by splitting post injection (i.e., double post injection). Effects of injection pressure on exhaust gas temperature were dependent on combustion phasing and injection strategies.

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

Experimental investigations on combustion of jatropha methyl ester in a turbocharged direct-injection diesel engine

2008 ◽  
Vol 222 (10) ◽  
pp. 1865-1877 ◽  
Author(s):  
K Anand ◽  
R P Sharma ◽  
P S Mehta
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Peak Pressure ◽  
Direct Injection ◽  
Pressure Rise ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Gas Temperature

Suitability of vegetable oil as an alternative to diesel fuel in compression ignition engines has become attractive, and research in this area has gained momentum because of concerns on energy security, high oil prices, and increased emphasis on clean environment. The experimental work reported here has been carried out on a turbocharged direct-injection multicylinder truck diesel engine using diesel fuel and jatropha methyl ester (JME)-diesel blends. The results of the experimental investigation indicate that an increase in JME quantity in the blend slightly advances the dynamic fuel injection timing and lowers the ignition delay compared with the diesel fuel. A maximum rise in peak pressure limited to 6.5 per cent is observed for fuel blends up to 40 per cent JME for part-load (up to about 50 per cent load) operations. However, for a higher-JME blend, the peak pressures decrease at higher loads remained within 4.5 per cent. With increasing proportion of JME in the blend, the peak pressure occurrence slightly advances and the maximum rate of pressure rise, combustion duration, and exhaust gas temperature decrease by 9 per cent, 15 per cent and 17 per cent respectively. Although the changes in brake thermal efficiencies for 20 per cent and 40 per cent JME blends compared with diesel fuel remain insignificant, the 60 per cent JME blend showed about 2.7 per cent improvement in the brake thermal efficiency. In general, it is observed that the overall performance and combustion characteristics of the engine do not alter significantly for 20 per cent and 40 per cent JME blends but show an improvement over diesel performance when fuelled with 60 per cent JME blend.

Tribological and emission characteristics of indirect ignition diesel engine fuelled with waste edible oil

2016 ◽  
Vol 68 (5) ◽  
pp. 554-560 ◽  
Author(s):  
De-Xing Peng
Keyword(s):  
Economic Growth ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Fuel Injection ◽  
Engine Performance ◽  
Vital Role ◽  
Fuel Additive ◽  
Content Type ◽  
Lubricating Property

Purpose Energy is the prime mover of economic growth and is vital to the sustenance of a modern economy. Future economic growth depends heavily on the long-term availability of energy from sources that are affordable, accessible and environmentally friendly. Regulating the sulfur content in diesel fuel is expected to reduce the lubricity of these fuels, which may result in increased wear and damage of fuel injection systems in diesel engines. Design/methodology/approach The tribological properties of the biodiesels as additive in pure petro-diesel are studied by ball-on-ring wear tester to find optimal concentration, and the mechanism of the reduction of wear and friction will be investigated by optical microscopy. Findings Studies have shown that low concentrations of biodiesel blends are more effective as lubricants because of their superior polarity. Using biodiesel as a fuel additive in a pure petroleum diesel fuel improves engine performance and exhaust emissions. The high biodegradability and superior lubricating property of biodiesel when used in compression ignition engines renders it an excellent fuel. Originality/value This detailed experimental investigation confirms that biodiesel can substitute mineral diesel without any modification in the engine. The use of biofuels as diesel engine fuels can play a vital role in helping the developed and developing countries to reduce the environmental impact of fossil fuels.

A Survey of Analysis, Modeling, and Diagnostics of Diesel Fuel Injection Systems

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Tomi R. Krogerus ◽  
Mika P. Hyvönen ◽  
Kalevi J. Huhtala
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Power Plants ◽  
Fuel Injection ◽  
High Reliability ◽  
Injection System ◽  
Engine Fuel ◽  
Injection Equipment ◽  
Diesel Fuel Injection

Diesel engines are widely used due to their high reliability, high thermal efficiency, fuel availability, and low consumption. They are used to generate power, e.g., in passenger cars, ships, power plants, marine offshore platforms, and mining and construction machines. The engine is at heart of these applications, so keeping it in good working condition is vital. Recent technical and computational advances and environmental legislation have stimulated the development of more efficient and robust techniques for the diagnostics of diesel engines. The emphasis is on the diagnostics of faults under development and the causes of engine failure or reduced efficiency. Diesel engine fuel injection plays an important role in the development of the combustion in the engine cylinder. Arguably, the most influential component of the diesel engine is the fuel injection equipment; even minor faults can cause a major loss of efficiency of the combustion and an increase in engine emissions and noise. With increased sophistication (e.g., higher injection pressures) being required to meet continuously improving noise, exhaust smoke, and gaseous emission regulations, fuel injection equipment is becoming even more susceptible to failure. The injection systems have been shown to be the largest contributing factor in diesel engine failures. Extracting the health information of components in the fuel injection system is a very demanding task. Besides the very time-consuming nature of experimental investigations, direct measurements are also limited to selected observation points. Diesel engine faults normally do not occur in a short timeframe. The modeling of typical engine faults, particularly combustion related faults, in a controlled manner is thus vital for the development of diesel engine diagnostics and fault detection. Simulation models based on physical grounds can enlarge the number of studied variables and also obtain a better understanding of localized phenomena that affect the overall behavior of the system. This paper presents a survey of the analysis, modeling, and diagnostics of diesel fuel injection systems. Typical diesel fuel injection systems and their common faults are presented. The most relevant state of the art research articles on analysis and modeling of fluid injection systems as well as diagnostics techniques and measured signals describing the behavior of the system are reviewed and the results and findings are discussed. The increasing demand and effect of legislation related to diagnostics, especially on-board diagnostics (OBD), are discussed with reference to the future progress of this field.

scholarly journals RESEARCH ON THE PROCESS OF BIOFUEL INJECTION / BIODEGALŲ IŠPURŠKIMO PROCESO TYRIMAS

2012 ◽  
Vol 4 (4) ◽  
pp. 381-385
Author(s):  
Birutė Skukauskaitė ◽  
Tomas Mickevičius
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Diesel Fuel ◽  
Rapeseed Oil ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Fuel Spray ◽  
Chamber Volume ◽  
Air Density ◽  
Engine Combustion

The purpose of this research was to examine penetration peculiarities of rapeseed oil injected into the combustion chamber of a diesel engine. For conducting tests, a stand imitating conditions (air density) for the engine combustion chamber was designed. The analysis of pictures obtained using a fast recording camera determined fuel injection into the chamber volume and calculated the velocity of spray head. It was established that fuel spray of injected rapeseed oil proceeds deeper into the combustion chamber than that of mineral diesel fuel. The parameters of fuel spray are mainly influenced by injection pressure rather than by the density of compressed gases. Santrauka Šio darbo tikslas buvo ištirti į dyzelinio variklio degimo kamerą įpurškiamos rapsų aliejaus čiurkšlės kitimo ypatumus, lyginant su mineraliniu dyzelinu. Tyrimams sukonstruotas stendas, kuriame buvo imituojamos sąlygos (oro tankis), esančios variklio degimo kameroje. Analizuojant spartaus filmavimo vaizdo kamera gautus vaizdus, buvo išmatuotas degalų čiurkšlės įsiskverbimo į degimo kamerą dydis, apskaičiuotas čiurkšlės fronto judėjimo greitis. Nustatyta, kad įpurškiamo rapsų aliejaus čiurkšlė į degimo kamerą įsiskverbia giliau, negu mineralinio dyzelino čiurkšlė. Įpurškiamų degalų čiurkšlės parametrams didesnės įtakos turi įpurškimo slėgis nei aplinkos dujų tankis.

scholarly journals The Influence of Diesel Oil Improvers on Indices of Atomisation and Combustion in High-Efficiency Engines

2017 ◽  
Vol 24 (3) ◽  
pp. 99-105 ◽  
Author(s):  
Ireneusz Pielecha ◽  
Jacek Pielecha ◽  
Maciej Skowron ◽  
Aleksander Mazanek
Keyword(s):  
Diesel Engine ◽  
Physicochemical Properties ◽  
Diesel Fuel ◽  
Liquid Fuel ◽  
High Efficiency ◽  
Fuel Injection ◽  
Diesel Oil ◽  
Fuel Combustion

Abstract The process of fuel combustion in a diesel engine is determined by factors existing during liquid fuel injection and atomisation. The physicochemical properties of the fuel to a large extent decide upon the quality of this phase of cylinder fuelling. So it is important to ensure appropriate properties of a fuel affecting its atomisation and, as a result, combustion. The paper deals with the topic of diesel oil improvers and the analysis of their influence on atomisation and combustion indices. In the studies base diesel oil and a diesel fuel improved by a package of additives, were used. The process of conventional and improved fuel injection was analysed by using optical examinations. The amount of released heat was evaluated during the studies carried out on combustion. Significant aspects of the applied improvers in relation to fuel injection and its combustion have been indicated.

Sign in / Sign up

Export Citation Format

Share Document