scholarly journals Spectrophotometric method for determination of ranitidine hydrochloride in bulk and in pharmaceutical preparation using ninhydrin

2020 ◽  
Vol 11 (4) ◽  
pp. 291-297
Author(s):  
Hutaf Mustafa Baker ◽  
Hussam Ahmad Alsaoud ◽  
Hamzeh Mohamad Abdel-Halim
Keyword(s):  
Spectrophotometric Method ◽  
Limit Of Detection ◽  
Pharmaceutical Preparation ◽  
Pharmaceutical Preparations ◽  
Molar Absorptivity ◽  
Limit Of Quantification ◽  
Ranitidine Hydrochloride ◽  
Relative Standard ◽  
Reproducible Method

A simple, sensitive and reproducible method for the determination of ranitidine hydrochloride in pharmaceutical preparations was investigated. This spectrophotometric method was based on the formation of a deep red color product with ninhydrin in basic media and the absorbance measured at λmax = 480 nm. The reaction occurs at 45 °C with pH = 10 having a contact time of 38 minutes. Under the optimum conditions, Beer’s Law is obeyed in the concentration range of 8.98×103 - 9.90×104 µg/L. The coefficient of correlation was found to be 0.999 for the obtained method with molar absorptivity of 3.05×103 L/mol.cm. The calculated Sandell’s sensitivity is 0.108 μg/cm2. The limit of detection and limit of quantification are 0.0997 and 0.3023 µg/mL, respectively. The low values of the percentage relative standard deviation and percentage relative error indicate the high precision and the good accuracy of the proposed method. The stoichiometry of the reaction is determined and found to be 1:4 (Ranitidine hydrochloride:Ninhydrin). The initial rate method confirmed that this reaction is first order one.

scholarly journals Spectrophotometric and RP-HPLC Methods for Determining Cefotaxime Sodium in Pharmaceutical Preparations

2020 ◽  
Vol 32 (6) ◽  
pp. 1314-1320
Author(s):  
Lamya A. Sarsam ◽  
Salim A. Mohammed ◽  
Sahar A. Fathe
Keyword(s):  
Limit Of Detection ◽  
Phosphate Buffer Solution ◽  
Pharmaceutical Preparations ◽  
Molar Absorptivity ◽  
Hplc Method ◽  
Buffer Solution ◽  
Limit Of Quantification ◽  
Rp Hplc ◽  
Relative Standard

A rapid, simple and sensitive spectrophotometric and RP-HPLC methods have been developed for the quantitative determination of cefotaxime-Na in both pure and dosage forms. The spectrophotometric method was based on diazotization of cefotaxime-Na and then coupling with 8-hydroxyquinoline in an alkaline medium. The resulting azo dye exhibited maximum absorption at 551 nm with a molar absorptivity of 0.597 × 104 L mol-1 cm-1. Beer′s law was obeyed over the range 10-700 μg/25 mL (i.e. 0.4-28.0 ppm) with an excellent determination coefficient (R2 = 0.9993). The limit of detection (LOD) and limit of quantification (LOQ) were found to be 0.0194 and 0.3765 μg mL-1, respectively. The recoveries were obtained in the range 97.3-102.5% and the relative standard deviation (RSD) was better than ± 1.56. The HPLC method has been developed for the determination of cefotaxime-Na. The analysis were carried out on a C18 column and a mobile phase composed of acetonitrile and phosphate buffer solution (0.024M KH2PO4 and 0.01M H3PO4) at pH 3.5 in the ratio of 60:40 (v:v), with a flow rate of 1.0 mL min-1 and UV detection at 258 nm. The proposed method showed good linearity (in a range of concentration 1.0-200 μg mL-1. The recovery percent and a relative standard deviations were found in the range 96 to 104.8% and ± 0.017 to ± 0.031%, respectively. Both methods were applied successfully to the assay of cefotaxime-Na in commercial injection preparations.

scholarly journals Simple UV Spectrophotometric Method for the Determination of Fluvastatin Sodium in Bulk and Pharmaceutical Formulations

2009 ◽  
Vol 6 (4) ◽  
pp. 1233-1239 ◽  
Author(s):  
J. Saminathan ◽  
A. S. Sankar ◽  
K. Anandakumar ◽  
T. Vetrichelvan
Keyword(s):  
Spectrophotometric Method ◽  
Limit Of Detection ◽  
Regression Line ◽  
Cost Effective ◽  
Pharmaceutical Formulations ◽  
Molar Absorptivity ◽  
Good Precision ◽  
Limit Of Quantification ◽  
Relative Standard

A simple and cost effective spectrophotometric method is described for the determination of fluvastatin sodium in pure form and in pharmaceutical formulations. When the drug reacts with sodium hydroxide shows absorption maximum at 304 nm and obeys beer's law in the concentration range 5-25 µg mL-1. The absorbance was found to increase linearly with increasing concentration of FVS, which is corroborated by the calculated correlation coefficient value of 0.9999 (n=5). The apparent molar absorptivity and sandell sensitivity were 1.1905×104and 0.0368844 µg cm-2cm respectively. The slope and intercept of the equation of the regression line are 0.027112 and 0.003539 respectively. The limit of detection and limit of quantification was found to be 0.0811 µg mL-1& 0.2460 µg mL-1. The validity of the described procedure was assessed. Statistical analysis of the result has been carried out revealing high accuracy and good precision. The proposed method was successfully applied to the determination of FVS in pharmaceutical formulations without any interference from common excipients. The relative standard deviations were ≤ 0.937%, with recoveries of 98.60% -101.70%.

scholarly journals Spectrophotometric determination of methyldopa in pharmaceutical preparation via ion pair formation

2019 ◽  
Vol 10 (2) ◽  
pp. 1367-1371
Author(s):  
Khalaf F Al Samarrai ◽  
Eman Thiab A Al Samarrai ◽  
Baidaa Adnan Al Samarrai
Keyword(s):  
Limit Of Detection ◽  
Low Cost ◽  
Pharmaceutical Preparation ◽  
Pharmaceutical Preparations ◽  
Molar Absorptivity ◽  
Ion Pair ◽  
Pair Formation ◽  
Limit Of Quantification ◽  
Ion Pair Formation

A simple, rapid and low-cost spectrophotometric method for determination of Methyldopa (MDA) based on ion-pair formation using Bromothymol blue (BTB) as a reagent in alkaline medium (pH 8.7). The absorbance of the green-blue-coloured product is measured at 616 nm. Beer's Law is obeyed at concentration range up to 5-20μg/ml with molar absorptivity 0.8279x104 L/mol.cm. The correlation coefficient, limit of detection and limit of quantification were 0.9982, 0.4318 μg/ml and 1.4393 μg/ml respectively. The method has been successfully applied to the determination of Methyldopa in pharmaceutical preparations.

scholarly journals Estimation of Furosemide in Pharmaceutical Preparation Samples

2020 ◽  
Vol 1 (1) ◽  
Keyword(s):  
Standard Deviation ◽  
Spectrophotometric Method ◽  
Pharmaceutical Preparation ◽  
Pharmaceutical Preparations ◽  
Pharmaceutical Formulations ◽  
Molar Absorptivity ◽  
Oral Solution ◽  
Average Recovery ◽  
Relative Standard

A simple, accurate, precise, rapid, economical and sensitive ultraviolet spectrophotometric method has been developed for the determination of Furosemide in pharmaceutical preparations, which shows maximum absorbance at 228 nm in. Beer’s law was obeyed in the range of 1 -10 μg/ ml, with molar absorptivity of 3.5×104 L.mol-1.cm-1, relative standard deviation of the method was less than 1.4%, and accuracy (average recovery %) was 100 ± 1.0. The method was successfully applied to the determination of Furosemide in some pharmaceutical formulations (tablets, Oral solution and injection) samples. The proposed method was validated by sensitivity and precision which proves suitability for the routine analysis of Furosemide in true samples.

scholarly journals Spectrophotometric determination of Phenylephrine hydrochloride and Salbutamol sulphate drugs in pharmaceutical preparations using diazotized Metoclopramide hydrochloride

2015 ◽  
Vol 12 (1) ◽  
pp. 167-177 ◽  
Author(s):  
Baghdad Science Journal
Keyword(s):  
Limit Of Detection ◽  
Pharmaceutical Preparations ◽  
Correlation Coefficients ◽  
Limit Of Quantification ◽  
Pharmaceutical Dosage Forms ◽  
Salbutamol Sulphate ◽  
Phenylephrine Hydrochloride ◽  
Relative Standard ◽  
Metoclopramide Hydrochloride

A spectrophotometric method has been proposed for the determination of two drugs containing phenol group [phenylephrine hydrochloride (PHP) and salbutamol sulphate (SLB)] in pharmaceutical dosage forms. The method is based on the diazotization reaction of metoclopramide hydrochloride (MCP) and coupling of the diazotized reagent with drugs in alkaline medium to give intense orange colored product (?max at 470 nm for each of PHP and SLB). Variable parameters such as temperature, reaction time and concentration of the reactants have been analyzed and optimized. Under the proposed optimum condition, Beer’s law was obeyed in the concentration range of 1-32 and 1-14 ?g mL-1 for PHP and SLB, respectively. The limit of detection (LOD) and limit of quantification (LOQ) for each of PHP and SLB were 0.60, 0.52 ?g mL-1 and 2.02, 1.72 ?g mL-1, respectively. No interference was observed from common excipients present in pharmaceutical preparations. The good correlation coefficients and low relative standard deviation assert the applicability of this method. The suggested method was further applied for the determinations of drugs in commercial pharmaceutical preparations, which was compared statistically with reference methods by means of t- test and F- test and were found not to differ significantly at 95% confidence level. The procedure was characterized by its simplicity with accuracy and precision.

scholarly journals Flotation-Spectrophotometric Method for the Determination of Aluminium ion Using Xylenol Orange

2011 ◽  
Vol 8 (4) ◽  
pp. 1528-1535 ◽  
Author(s):  
F. Nekouei ◽  
Sh. Nekouei
Keyword(s):  
Standard Deviation ◽  
Spectrophotometric Method ◽  
Calibration Curve ◽  
Limit Of Detection ◽  
Xylenol Orange ◽  
Molar Absorptivity ◽  
Relative Standard ◽  
Ion Associate ◽  
Sensitive Method

A simple, fast, reproducible and sensitive method for the flotation- spectrophotometric determination of Al3+is reported. The apparent molar absorptivity (ε) of the ion associate was determined to be 8.35×104L mol-1cm-1. The calibration curve was linear in the concentration range of 1.0-50 ng mL-1of Al3+with a correlation coefficient of 0.9997. The limit of detection (LOD) was 0.621 ng mL. The relative standard deviation (RSD) at 10 and 30 ng mL-1of aluminium were 1.580 and 2.410% (n=7) respectively. The method was applied for measuring the amount of aluminium in water samples.

scholarly journals Ultraviolet Spectrophotometric Method for Determination of Glipizide in Presence of Liposomal/Proliposomal Turbidity

2013 ◽  
Vol 2013 ◽  
pp. 1-5
Author(s):  
Neelkant Prasad ◽  
Roshan Issarani ◽  
Badri Prakash Nagori
Keyword(s):  
Spectrophotometric Method ◽  
Calibration Curve ◽  
Limit Of Detection ◽  
Quantitative Estimation ◽  
Uv Detection ◽  
Limit Of Quantification ◽  
Relative Standard ◽  
Precision And Accuracy ◽  
Clear Solution

A simple and sensitive ultraviolet spectrophotometric method for quantitative estimation of glipizide in presence of lipid turbidity is described to avoid false estimation due to diffraction by turbidity. UV detection was performed at 230 nm, 225 nm, and 235 nm, and the calibration curve was plotted between resultant of absorbance of [230 nm − (225 nm + 235 nm)/2] and concentration of analyte. The calibration curve was linear over the concentration range tested (1–20 μg/mL) with limit of detection of 0.27 μg/mL and limit of quantification of 0.82 μg/mL. Percent relative standard deviations and percent relative mean error, representing precision and accuracy, respectively, for clear as well as turbid solutions, were found to be within acceptable limits, that is, always less than 0.69 and 0.41, respectively, for clear solution and 0.65 and 0.47, respectively, for turbid solution. Conclusively, our method was successfully applied for the determination of glipizide in clear as well as turbid solutions, and it was found that the drug analyte in both types of solutions can be detected from the same calibration curve accurately and precisely and glipizide entrapped in the liposomes or in proliposomal matrix was not detected.

scholarly journals Rapid and Sensitive Spectrophotometric Method for the Determination of the Trace Amount of Thallium (III) in Water and Urine Samples by New Oxidative Coupling Reaction

2019 ◽  
Vol 53 (4) ◽  
Author(s):  
Padmarajaiah Nagaraja ◽  
Naef Ghllab Saeed Al-Tayar ◽  
Anantharaman Shivakumar ◽  
Ashwinee Kumar Shresta ◽  
Avinash K. Gowda
Keyword(s):  
Spectrophotometric Method ◽  
Limit Of Detection ◽  
Rapid Determination ◽  
Coupling Reaction ◽  
Molar Absorptivity ◽  
Urine Samples ◽  
Oxidative Coupling Reaction ◽  
Relative Standard ◽  
Student’S T

A very simple, sensitive and fairly selective direct spectrophotometric method is presented for the rapid determination of thallium(III) at trace level. The method is based on the oxidation of 2-hydrazono-3-methyl-2,3-dihydrobenzo[d]thiazole hydrochloride (MBTH) by thallium(III) in phosphoric acid medium to form a diazoniumcation, which couples immediately with 10,11-dihydro-5Hdibenzo[b,f]azepine (IDB) at room temperature giving a blue colored species having a maximum absorption at 660 nm. The reaction conditions and other important analytical parameters were optimized.The calibration curve was found to be linear over the range of 0.1-4 μg/mL with molar absorptivity of 4.5 × 104 L mol- cm-1 and Sandell’s sensitivity of 0.00454 μg cm-2. The relative standard deviation and limit of detection have been found to be 0.58% and 0.0147 μg/mL respectively. Almost all common anions and cations are found notto interfering in matrix level of the analytical process. The method has been successfully applied for the determination of thallium(III) in synthetic standard mixtures, water and human urine samples. The performance of proposed method was evaluated in terms of student’s t-test and variance ratio F-test, to find out the significance of proposed method over the reported methods.    

scholarly journals SPECTROPHOTOMETRIC DETERMINATION OF CEFPIROME IN PHARMACEUTICAL PREPARATION

2020 ◽  
pp. 124-127
Author(s):  
DILIP M CHAFLE
Keyword(s):  
Standard Deviation ◽  
Spectrophotometric Method ◽  
Limit Of Detection ◽  
Pharmaceutical Preparation ◽  
Effect Of Temperature ◽  
Percentage Error ◽  
Ferric Nitrate ◽  
Red Color ◽  
Relative Standard

Objective: A simple, sensitive and precise visible spectrophotometric method has been proposed for the determination of cefpirome (CFM) in pure and oral injectable dosage form. Methods: A spectrophotometric method is based on the formation of stable red color product by oxidation of drugs by ferric nitrate and subsequent complexation with 1, 10 – phenanthroline with maximum absorption at 515 nm. Result: The red color complex was formed between Fe (II) and 1, 10 – phenanthroline after reduction of Fe (III) to Fe (II) in the presence of CFM drug. The phosphoric acid solution was used only for quenching the complex formation reaction. Several parameters such as the maximum wavelength of absorption, the volume of reagents, sequence of addition and effect of temperature and time of heating were optimized to achieve high sensitivity, stability and reproducible results. Under the optimum conditions, linear relationship with good correlation coefficient (0.994) was found over the concentration range from 0.20 to 6.00 μg/mL with a molar extinction coefficient 7.7813 × 104 L/mol/cm, limit of detection 0.2026 and limit of quantification 0.6141 μg/mL, respectively. Conclusion: The proposed method was evaluated statistically for linearity, accuracy, and precision in terms of standard deviation, percentage recovery, percentage error and relative standard deviation. The proposed method can be applied for the routine estimation of CFM in the laboratory.

scholarly journals ULTRAVIOLET-SPECTROPHOTOMETRIC METHOD DEVELOPMENT AND VALIDATION FOR THE DETERMINATION OF NORFLOXACIN PRESENT IN TASTE MASKED DRUG RESIN COMPLEX

2018 ◽  
Vol 11 (4) ◽  
pp. 244
Author(s):  
Ayya Rajendra Prasad ◽  
Jayanthi Vijaya Ratna
Keyword(s):  
Spectrophotometric Method ◽  
Absorption Maximum ◽  
Method Development ◽  
Limit Of Detection ◽  
Statistical Parameters ◽  
Limit Of Quantification ◽  
Relative Standard ◽  
Validation Parameters ◽  
Development And Validation

 Objective: The objective of this study was developed and validated a novel, specific, precise, and simple ultraviolet (UV)-spectrophotometric method for the estimation of norfloxacin present in taste masked drug-resin complex.Methods: UV-spectrophotometric determination was performed with ELICO SL 1500 UV-visible spectrophotometer using 0.1 N HCl as a medium. The spectrum of the standard solution was run from 200 to 400 nm range for the determination of absorption maximum (λ max). λ max of norfloxacin was found at 278 nm. The absorbance of standard solutions of 1, 2, 3, 4, and 5 μg/ml of drug solution was measured at an absorption maximum at 278 nm against the blank. Then, a graph was plotted by taking concentration on X-axis and absorbance on Y-axis which gave a straight line. Validation parameters such as linearity and range, selectivity and specificity, limit of detection (LOD) and limit of quantification (LOQ), accuracy, precision, and robustness were evaluated as per the International Conference on Harmonization (ICH) guidelines.Results: Linearity for the UV-spectrophotometric method was noted over a concentration range of 1–5 μg/ml with a correlation coefficient of 0.9995. The LOD and LOQ for norfloxacin were found at 0.39 μg/ml and 1.19 μg/ml, respectively. Accuracy was in between 99.00% and 99.17%. % relative standard deviation for repeatability, intraday precision, and interday precision was found to be 0.600, in between 0.291 and 0.410, and in between 0.682 and 1.439, respectively. The proposed UV spectrophotometric method is found to be robust.Conclusion: The proposed UV-spectrophotometric method was validated according to the ICH guidelines, and results and statistical parameters demonstrated that the developed method is sensitive, precise, reliable, and simple for the estimation of norfloxacin present in taste masked drug-resin complex.

Sign in / Sign up

Export Citation Format

Share Document