scholarly journals Application of a diode array spectroradiometer to measuring the spectral scattering properties of cloud types in a laboratory

2007 ◽  
Vol 7 (22) ◽  
pp. 5803-5813 ◽  
Author(s):  
A. R. D. Smedley ◽  
A. R. Webb ◽  
C. P. R. Saunders
Keyword(s):  
Single Scattering ◽  
Small Scale ◽  
Diode Array ◽  
Full Spectrum ◽  
Solar Radiation Incident ◽  
Scattering Phase ◽  
Set Up ◽  
Phase Functions ◽  
Mixed Phase Clouds ◽  
Ultraviolet Solar Radiation

Abstract. In the last few years diode array spectroradiometers have become useful complements to traditional scanning instruments when measuring visible and ultraviolet solar radiation incident on the ground. This study describes the application of such an instrument to the problem of measuring the radiation scattered by different cloud-types in a laboratory environment. Details of how the instrument is incorporated into the experimental set-up are given together with the development of the system as a whole. The capability to measure a full spectrum for each scattering angle is an undoubted advantage, although the limited sensitivity impacts on the usefulness for optically thin clouds. Nevertheless example results are presented: (1) scattering phase functions at a range of wavelengths recorded simultaneously for water clouds, showing spectral deviation at the rainbow angle and verification of Mie theory; (2) likewise for mixed phase clouds, with evidence of both halo and rainbow features in a single scattering function; and, (3) detail of the forward scattering region in a glaciated cloud showing a barely perceptible halo feature, with implications for the small-scale structure of the ice crystals produced.

scholarly journals Application of a diode array spectroradiometer to measuring the spectral scattering properties of cloud types in a laboratory

2007 ◽  
Vol 7 (4) ◽  
pp. 10767-10797
Author(s):  
A. R. D. Smedley ◽  
A. R. Webb ◽  
C. P. R. Saunders
Keyword(s):  
Dynamic Range ◽  
Single Scattering ◽  
Small Scale ◽  
Diode Array ◽  
Full Spectrum ◽  
Solar Radiation Incident ◽  
Scattering Phase ◽  
Set Up ◽  
Phase Functions ◽  
Mixed Phase Clouds

Abstract. In the last few years diode array spectroradiometers have become useful complements to traditional scanning instruments when measuring visible and ultraviolet solar radiation incident on the ground. This study describes the application of such an instrument to the problem of measuring the radiation scattered by different cloud types in a laboratory environment. Details of how the instrument is incorporated into the experimental set-up are given together with the development of the system as a whole. The capability to measure a full spectrum for each scattering angle is an undoubted advantage, although the limited dynamic range impacts on the usefulness for optically thin clouds. Nevertheless example results are presented: (1) scattering phase functions at a range of wavelengths recorded simultaneously for water clouds, showing spectral deviation at the rainbow angle and verification of Mie theory; (2) likewise for mixed phase clouds, with evidence of both halo and rainbow features in a single scattering function; and, (3) detail of the forward scattering region in a glaciated cloud showing a barely perceptible halo feature, with implications for the small-scale structure of the ice crystals produced.

Statistical estimates of the effect of the sea water scattering phase function on the characteristics of airborne hydrooptical lidar signals

2021 ◽  
pp. 171-177
Author(s):  
A.A. Lisenko ◽  
◽  
V.S. Shamanaev ◽  
Keyword(s):  
Sea Water ◽  
Water Layer ◽  
Single Scattering ◽  
Airborne Lidar ◽  
Statistical Estimates ◽  
Scattering Approximation ◽  
Coastal Sea ◽  
Scattering Phase ◽  
Scattering Phase Function ◽  
Phase Functions

The effect of the scattering phase functions of sea water types by the Petzold classification on the characteristics of signals of an airborne lidar is investigated using the Monte Carlo method. It is shown that for pure and coastal waters, the single scattering approximation is applicable for solving the laser sensing equation. Based on the analysis of the results obtained in the closed numerical experiment, the method of reconstruction of the extinction coefficient of lidar signals by pure and coastal sea waters in the mixing water layer is proposed and substantiated. The obtained results can be used to expand the possibilities of lidar signal interpretation, especially in complex and ambiguous situations.

scholarly journals Modelling Laboratory Data of Bidirectional Reflectance of a Regolith Surface Containing Alumina

2011 ◽  
Vol 28 (3) ◽  
pp. 261-265 ◽  
Author(s):  
C. Bhattacharjee ◽  
D. Deb ◽  
H. S. Das ◽  
A. K. Sen ◽  
R. Gupta
Keyword(s):  
Laboratory Data ◽  
Size Composition ◽  
Single Scattering ◽  
Bidirectional Reflectance ◽  
Reflection Function ◽  
Versus Phase ◽  
Scattering Phase ◽  
Scattering Phase Function ◽  
Phase Functions ◽  
Bidirectional Reflection

AbstractBidirectional reflectance of a surface is defined as the ratio of the scattered radiation at the detector to the incident irradiance as a function of geometry. Accurate knowledge of the bidirectional reflection function for layers composed of discrete, randomly positioned scattering particles is essential for many remote sensing, engineering, and biophysical applications, as well as for different areas of astrophysics. Computations of bidirectional reflection functions for plane parallel particulate layers are usually reduced to solving the radiative transfer equation by the existing techniques. In this work we present our laboratory data on bidirectional reflectance versus phase angle for two sample sizes of alumina, 0.3 and 1 μm, for the He–Ne laser at wavelengths of 632.8 nm (red) and 543.5 nm (green). The nature of the phase curves of the asteroids depends on the parameters like particle size, composition, porosity, roughness, etc. In the present study we analyze data which are being generated using a single scattering phase function, that is, Mie theory of treating particles as a compact sphere. The well-known Hapke formula, along with different particle phase functions such as Mie and Henyey–Greenstein, will be used to model the laboratory data obtained at the asteroid laboratory of Assam University.

scholarly journals Modification of a Solar Thermal Collector to Promote Heat Transfer inside an Evacuated Tube Solar Thermal Absorber

2021 ◽  
Vol 11 (9) ◽  
pp. 4100
Author(s):  
Rasa Supankanok ◽  
Sukanpirom Sriwong ◽  
Phisan Ponpo ◽  
Wei Wu ◽  
Walairat Chandra-ambhorn ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Solar Thermal ◽  
Heat Transfer Fluid ◽  
Small Scale ◽  
Medium Temperature ◽  
Change Behavior ◽  
Set Up ◽  
Evacuated Tube ◽  
Heating Medium

Evacuated-tube solar collector (ETSC) is developed to achieve high heating medium temperature. Heat transfer fluid contained inside a copper heat pipe directly affects the heating medium temperature. A 10 mol% of ethylene-glycol in water is the heat transfer fluid in this system. The purpose of this study is to modify inner structure of the evacuated tube for promoting heat transfer through aluminum fin to the copper heat pipe by inserting stainless-steel scrubbers in the evacuated tube to increase heat conduction surface area. The experiment is set up to measure the temperature of heat transfer fluid at a heat pipe tip which is a heat exchange area between heat transfer fluid and heating medium. The vapor/ liquid equilibrium (VLE) theory is applied to investigate phase change behavior of the heat transfer fluid. Mathematical model validated with 6 experimental results is set up to investigate the performance of ETSC system and evaluate the feasibility of applying the modified ETSC in small-scale industries. The results indicate that the average temperature of heat transfer fluid in a modified tube increased to 160.32 °C which is higher than a standard tube by approximately 22 °C leading to the increase in its efficiency by 34.96%.

Numerical Study of Methane and Air Combustion Inside Heat-Recirculating Combustors

2013 ◽  
Author(s):  
Yanxia Li ◽  
Zhongliang Liu ◽  
Yan Wang ◽  
Jiaming Liu
Keyword(s):  
Gas Flow ◽  
Numerical Study ◽  
Convection Heat Transfer ◽  
Central Area ◽  
Small Scale ◽  
Inlet Velocity ◽  
Strong Convection ◽  
Simulation Results ◽  
Lean Fuel ◽  
Set Up

A numerical model on methane/air combustion inside a small Swiss-roll combustor was set up to investigate the flame position of small-scale combustion. The simulation results show that the combustion flame could be maintained in the central area of the combustor only when the speed and equivalence ratio are all within a narrow and specific range. For high inlet velocity, the combustion could be sustained stably even with a very lean fuel and the flame always stayed at the first corner of reactant channel because of the strong convection heat transfer and preheating. For low inlet velocity, small amounts of fuel could combust stably in the central area of the combustor, because heat was appropriately transferred from the gas to the inlet mixture. Whereas, for the low premixed gas flow, only in certain conditions (Φ = 0.8 ～ 1.2 when ν0 = 1.0m/s, Φ = 1.0 when ν0 = 0.5m/s) the small-scale combustion could be maintained.

scholarly journals Modeling of Aerosol Radiation-Relevant Parameters in the Troposphere of Siberia on the Basis of Empirical Data

Atmosphere ◽  
2018 ◽  
Vol 9 (11) ◽  
pp. 414 ◽  
Author(s):  
Mikhail Panchenko ◽  
Svetlana Terpugova ◽  
Victor Pol’kin ◽  
Valerii Kozlov ◽  
Dmitry Chernov
Keyword(s):  
Complex Refractive Index ◽  
West Siberia ◽  
Single Scattering ◽  
Single Scattering Albedo ◽  
Optical Characteristics ◽  
Asymmetry Factor ◽  
Size Spectrum ◽  
Scattering Phase ◽  
Scattering Phase Function ◽  
Modal Radius

The paper presents the generalized empirical model of the aerosol optical characteristics in the lower 5-km layer of the atmosphere of West Siberia. The model is based on the data of long-term airborne sensing of the vertical profiles of the angular scattering coefficient, aerosol disperse composition, as well as the content of absorbing particles. The model provides for retrieval of the aerosol optical characteristics in visible and near IR wavelength ranges (complex refractive index, scattering and absorption coefficients, optical depth, single scattering albedo, and asymmetry factor of the scattering phase function). The main attention in the presented version of the model is given to two aspects: The study of the effect of the size spectrum of the absorbing substance in the composition of aerosol particles on radiative-relevant parameters (the single scattering albedo (SSA) and the asymmetry factor (AF)) and the consideration of different algorithms for taking into account the relative humidity of air. The ranges of uncertainty of SSA and AF at variations in the modal radius of the absorbing fraction at different altitudes in the troposphere are estimated.

Small Scale Supercritical CO2 Radial Inflow Turbine Meanline Design Considerations

2018 ◽  
Author(s):  
Tina Unglaube ◽  
Hsiao-Wei D. Chiang
Keyword(s):  
High Velocity ◽  
Gas Turbines ◽  
Velocity Ratio ◽  
Maximum Efficiency ◽  
Design Parameters ◽  
Working Fluid ◽  
Small Scale ◽  
Optimum Velocity ◽  
Set Up ◽  
Very High

In recent years closed loop supercritical carbon dioxide Brayton cycles have drawn the attention of many researchers as they are characterized by a higher theoretic efficiency and smaller turbomachinery size compared to the conventional steam Rankine cycle for power generation. Currently, first prototypes of this emerging technology are under development and thus small scale sCO2 turbomachinery needs to be developed. However, the design of sCO2 turbines faces several new challenges, such as the very high rotational speed and the high power density. Thus, the eligibility of well-established radial inflow gas turbine design principles has to be reviewed regarding their suitability for sCO2 turbines. Therefore, this work reviews different suggestion for optimum velocity ratios for gas turbines and aims to re-establish it for sCO2 turbines. A mean line design procedure is developed to obtain the geometric dimensions for small scale sCO2 radial inflow turbines. By varying the specific speed and the velocity ratio, different turbine configurations are set up. They are compared numerically by means of CFD analysis to conclude on optimum design parameters with regard to maximum total-to-static efficiency. Six sets of simulations with different specific speeds between 0.15 and 0.52 are set up. Higher specific speeds could not be analyzed, as they require very high rotational speeds (more than 140k RPM) for small scale sCO2 turbines (up to 150kWe). For each set of simulations, the velocity ratio that effectuates maximum efficiency is identified and compared to the optimum parameters recommended for radial inflow turbines using subcritical air as the working fluid. It is found that the values for optimum velocity ratios suggested by Rohlik (1968) are rather far away from the optimum values indicated by the conducted simulations. However, the optimum values suggested by Aungier (2005), although also established for subcritical gas turbines, show an approximate agreement with the simulation results for sCO2 turbines. Though, this agreement should be studied for a wider range of specific speeds and a finer resolution of velocity ratios. Furthermore, for high specific speeds in combination with high velocity ratios, the pressure drop of the designed turbines is too high, so that the outlet pressure is beyond the critical point. For low specific speeds in combination with low velocity ratios, the power output of the designed turbines becomes very small. Geometrically, turbines with low specific speeds and high velocity ratios are characterized by very small blade heights, turbines with high specific speeds and small velocity ratios by very small diameters.

LO.CO.MO.DIA: Low Cost Monitoring for Diagnostic Purposes of a Small Scale CHP Plant

2000 ◽  
Author(s):  
Francesco Fantozzi ◽  
Umberto Desideri
Keyword(s):  
Data Acquisition ◽  
Internal Combustion Engines ◽  
Low Cost ◽  
Small Scale ◽  
Combustion Engines ◽  
Performance Indexes ◽  
Data Acquisition Board ◽  
Set Up ◽  
The University ◽  
Maintenance Personnel

Abstract Small scale Internal Combustion Engines (ICE) powered Combined Heat and Power (CHP) plants are economically convenient when availability and efficiencies are above specified limits. Nevertheless these plants are often run without a monitoring device capable of data storing and trending and of performance evaluation. This paper describes the setting up of a powerful low-cost monitoring system for the CHP plant that powers the School of Engineering of the University of Perugia. Data acquisition is performed by interfacing a Personal Computer (PC) to existing control panels via, serial port, and to a data acquisition board for those variables that are not measured by existing devices. Performance indexes are then calculated via software. Alarms and controls are stored as well to set up a database for diagnostic purposes. The monitoring itself has already shown its troubleshooting capability in interface to maintenance personnel: history trending of variables speeds up the phase of failure identification because it eliminates those possibilities that are negated by cross referencing values of different variables.

Sign in / Sign up

Export Citation Format

Share Document