scholarly journals Peptization Control of Composite Materials Containing Water Glass for Spray Drying of Catalysts

2021 ◽  
Vol 44 (4) ◽  
pp. 732-740
Author(s):  
Andres Carrasco Saavedra ◽  
Markus Seifert ◽  
Mariella Hannß ◽  
Thomas Henle ◽  
Mai Lê-Anh ◽  
...  
Keyword(s):  
Composite Materials ◽  
Spray Drying ◽  
Water Glass

scholarly journals The effect of alkali activation solutions with different water glass/NaOH solution ratios on geopolymer composite materials

2019 ◽  
Vol 660 ◽  
pp. 012003
Author(s):  
N Doğan-Sağlamtimur ◽  
H Öznur Öz ◽  
A Bilgil ◽  
T Vural ◽  
E Süzgeç
Keyword(s):  
Composite Materials ◽  
Water Glass ◽  
Alkali Activation ◽  
Naoh Solution

Vacuum Free-Fall Method for Preparation of Randomly Oriented XRD Samples

1988 ◽  
Vol 32 ◽  
pp. 625-628
Author(s):  
Jim Ludlam ◽  
Brad Jacobs ◽  
Paul K. Predecki
Keyword(s):  
Composite Materials ◽  
Glass Fiber ◽  
Spray Drying ◽  
Phase Analysis ◽  
Free Fall ◽  
Quantitative Phase Analysis ◽  
Random Orientation ◽  
Crystallite Orientation ◽  
Air Suspension ◽  
Random Composite

Quantitative phase analysis by XRD requires the attainment of (1) random crystallite orientation and (2) homogeneous and intimate mixing of the constituent phases in the samples. These two requirements must also be met in the preparation of random composite materials, particularly those containing randomly-oriented fibers or whiskers.The two most common methods for producing random crystallite orientation are spray drying and the air suspension method. In the latter, an air suspension of the crystallites is rapidly collected onto a glass fiber filter. The crystallites then assume the random orientation of the filter fibers on which they are deposited.

Comparative Microstructures of Ion Milled and Electrochemically Thinned Composite Materials

1974 ◽  
Vol 32 ◽  
pp. 546-547
Author(s):  
R.R. Russell
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Composite Materials ◽  
Great Difficulty ◽  
Ion Milling ◽  
Transmission Electron ◽  
Ion Damage ◽  
Intermetallic Composite

Transmission electron microscopy of metallic/intermetallic composite materials is most challenging since the microscopist typically has great difficulty preparing specimens with uniform electron thin areas in adjacent phases. The application of ion milling for thinning foils from such materials has been quite effective. Although composite specimens prepared by ion milling have yielded much microstructural information, this technique has some inherent drawbacks such as the possible generation of ion damage near sample surfaces.

Transmission electron microscopy of composite materials

1988 ◽  
Vol 46 ◽  
pp. 1012-1015
Author(s):  
K.P.D. Lagerlof
Keyword(s):  
Composite Materials ◽  
Physical Properties ◽  
Structural Defects ◽  
Structural Composites ◽  
Multiphase Materials ◽  
Structural Reinforcement ◽  
Transmission Electron ◽  
Reinforced Fiber ◽  
Particulate Reinforced Composites ◽  
Definition Of

Although most materials contain more than one phase, and thus are multiphase materials, the definition of composite materials is commonly used to describe those materials containing more than one phase deliberately added to obtain certain desired physical properties. Composite materials are often classified according to their application, i.e. structural composites and electronic composites, but may also be classified according to the type of compounds making up the composite, i.e. metal/ceramic, ceramic/ceramie and metal/semiconductor composites. For structural composites it is also common to refer to the type of structural reinforcement; whisker-reinforced, fiber-reinforced, or particulate reinforced composites [1-4].For all types of composite materials, it is of fundamental importance to understand the relationship between the microstructure and the observed physical properties, and it is therefore vital to properly characterize the microstructure. The interfaces separating the different phases comprising the composite are of particular interest to understand. In structural composites the interface is often the weakest part, where fracture will nucleate, and in electronic composites structural defects at or near the interface will affect the critical electronic properties.

Sign in / Sign up

Export Citation Format

Share Document