The Study of Retained Austenite by Means of Mössbauer Scattering Spectroscopy

1970 ◽  
pp. 229-239 ◽  
Author(s):  
H. K. Chow ◽  
R. L. Bogner
Keyword(s):  
Retained Austenite

The Effects of Quenching and Tempering Treatment on the Hardness and Microstructures of a Cold Work Steel

2019 ◽  
Vol 4 (1) ◽  
pp. 286-294
Author(s):  
László Tóth ◽  
Réka Fábián
Keyword(s):  
Heat Treatment ◽  
Retained Austenite ◽  
Elevated Temperatures ◽  
Cryogenic Treatment ◽  
Cold Work ◽  
Chromium Steel ◽  
Primary Carbide ◽  
Tempering Temperature ◽  
Tempering Treatment ◽  
Primary Carbides

The X153CrMoV12 ledeburitic chromium steel characteristically has high abrasive wear resistance, due to their high carbon and high chromium contents with a large volume of carbides in the microstructure. This steel quality has high compression strength, excellent deep hardenability and toughness properties, dimensional stability during heat treatment, high resistance to softening at elevated temperatures. The higher hardness of cryogenic treated samples in comparison with conventional quenched samples mean lower quantity of retained austenite as at samples quenched to room temperature and tempered in similar condition. In the microstructure of samples were observed that the primary carbide did not dissolve at 1070°C and their net structure have not been changed during to heat treatment. During to tempering at high temperature the primary carbides have become more and more rounded. After low tempering temperature in martensite were observed some small rounded carbides also, increasing the tempering temperature the quantity of finely dispersed carbides increased, which result higher hardness. The important issues in heat treatment of this steels are the reduction or elimination of retained austenite due to cryogenic treatment.

Retained austenite-induced fire-resistance of a 690 MPa high strength steel

2021 ◽  
Vol 291 ◽  
pp. 129448
Author(s):  
L.J. Wei ◽  
X.M. Ji ◽  
Y.S. Yu ◽  
R.D.K. Misra ◽  
P.C. Liu ◽  
...  
Keyword(s):  
Fire Resistance ◽  
High Strength Steel ◽  
Retained Austenite ◽  
High Strength

scholarly journals Effect of Sub-Zero Treatments and Tempering on Corrosion Behaviour of Vanadis 6 Tool Steel

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3759
Author(s):  
Peter Jurči ◽  
Aneta Bartkowska ◽  
Mária Hudáková ◽  
Mária Dománková ◽  
Mária Čaplovičová ◽  
...  
Keyword(s):  
Population Density ◽  
Corrosion Rate ◽  
Tool Steel ◽  
Retained Austenite ◽  
Corrosion Behaviour ◽  
Considerable Reduction ◽  
Treated Steel ◽  
Precipitation Behaviour ◽  
Quenched Steel

Sub-zero treatment of Vanadis 6 steel resulted in a considerable reduction of retained austenite amount, refinement of martensite, enhancement of population density of carbides, and modification of precipitation behaviour. Tempering of sub-zero-treated steel led to a decrease in population density of carbides, to a further reduction of retained austenite, and to precipitation of M3C carbides, while M7C3 carbides precipitated only in the case of conventionally quenched steel. Complementary effects of these microstructural variations resulted in more noble behaviour of sub-zero-treated steel compared to the conventionally room-quenched one, and to clear inhibition of the corrosion rate at the same time.

scholarly journals Heat Treatment Design for a QP Steel: Effect of Partitioning Temperature

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1136
Author(s):  
Marcel Carpio ◽  
Jessica Calvo ◽  
Omar García ◽  
Juan Pablo Pedraza ◽  
José María Cabrera
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Quenching Temperature ◽  
Advanced High Strength Steels ◽  
New Family ◽  
Automotive Parts ◽  
Fresh Martensite ◽  
Industry Needs

Designing a new family of advanced high-strength steels (AHSSs) to develop automotive parts that cover early industry needs is the aim of many investigations. One of the candidates in the 3rd family of AHSS are the quenching and partitioning (QP) steels. These steels display an excellent relationship between strength and formability, making them able to fulfill the requirements of safety, while reducing automobile weight to enhance the performance during service. The main attribute of QP steels is the TRIP effect that retained austenite possesses, which allows a significant energy absorption during deformation. The present study is focused on evaluating some process parameters, especially the partitioning temperature, in the microstructures and mechanical properties attained during a QP process. An experimental steel (0.2C-3.5Mn-1.5Si (wt%)) was selected and heated according to the theoretical optimum quenching temperature. For this purpose, heat treatments in a quenching dilatometry and further microstructural and mechanical characterization were carried out by SEM, XRD, EBSD, and hardness and tensile tests, respectively. The samples showed a significant increment in the retained austenite at an increasing partitioning temperature, but with strong penalization on the final ductility due to the large amount of fresh martensite obtained as well.

The influence of retained austenite in high chromium cast iron on impact-abrasive wear

Wear ◽  
1990 ◽  
Vol 135 (2) ◽  
pp. 217-226 ◽  
Author(s):  
Tong Jian-Min ◽  
Zhou Yi-Zhong ◽  
Shen Tian-Yi ◽  
Deng Hai-Jin
Keyword(s):  
Cast Iron ◽  
Abrasive Wear ◽  
Retained Austenite ◽  
High Chromium ◽  
High Chromium Cast Iron ◽  
Chromium Cast Iron

scholarly journals The Effect of Different Annealing Strategies on the Microstructure Development and Mechanical Response of Austempered Steels

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1041
Author(s):  
Eliseo Hernandez-Duran ◽  
Luca Corallo ◽  
Tanya Ros-Yanez ◽  
Felipe Castro-Cerda ◽  
Roumen H. Petrov
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Mechanical Response ◽  
Steel Grade ◽  
The Other ◽  
Microstructure Development ◽  
Microstructural Refinement ◽  
Heterogeneous Distribution ◽  
Parent Austenite ◽  
Conventional Annealing

This study focuses on the effect of non-conventional annealing strategies on the microstructure and related mechanical properties of austempered steels. Multistep thermo-cycling (TC) and ultrafast heating (UFH) annealing were carried out and compared with the outcome obtained from a conventionally annealed (CA) 0.3C-2Mn-1.5Si steel. After the annealing path, steel samples were fast cooled and isothermally treated at 400 °C employing the same parameters. It was found that TC and UFH strategies produce an equivalent level of microstructural refinement. Nevertheless, the obtained microstructure via TC has not led to an improvement in the mechanical properties in comparison with the CA steel. On the other hand, the steel grade produced via a combination of ultrafast heating annealing and austempering exhibits enhanced ductility without decreasing the strength level with respect to TC and CA, giving the best strength–ductility balance among the studied steels. The outstanding mechanical response exhibited by the UFH steel is related to the formation of heterogeneous distribution of ferrite, bainite and retained austenite in proportions 0.09–0.78–0.14. The microstructural formation after UFH is discussed in terms of chemical heterogeneities in the parent austenite.

scholarly journals The Hybrid Process of Low-Pressure Carburizing and Metallization (Cr + LPC, Al + LPC) of 17CrNiMo7-6 and 10NiCrMo13-5 Steels

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 567
Author(s):  
Paulina Kowalczyk ◽  
Konrad Dybowski ◽  
Bartłomiej Januszewicz ◽  
Radomir Atraszkiewicz ◽  
Marcin Makówka
Keyword(s):  
Corrosion Resistance ◽  
Surface Layer ◽  
Physicochemical Properties ◽  
Surface Treatment ◽  
Retained Austenite ◽  
Treatment Process ◽  
Active Surface ◽  
Low Pressure ◽  
Low Alloy Steel ◽  
Chromium Plating

This paper presents the concept of modification of physicochemical properties of steels by simultaneous diffusion saturation with carbon and chromium or aluminum. The application of a hybrid surface treatment process consisting of a combination of aluminizing and low-pressure carburizing (Al + LPC) resulted in a reduction in the amount of retained austenite in the surface layer of the steel. While the use of chromium plating and low-pressure carburizing (Cr + LPC) induced an improvement in the corrosion resistance of the carburized steels. It is of particular importance in case of vacuum processes after the application of which the active surface corrodes easily, as well as in case of carburizing of low-alloy steel with nickel, where an increased content of retained austenite in the surface layer is found after carburizing.

scholarly journals Mechanical and thermal stability of retained austenite in plastically deformed bainite-based TRIP-aided medium-Mn steels

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Aleksandra Kozłowska ◽  
Adam Grajcar ◽  
Aleksandra Janik ◽  
Krzysztof Radwański ◽  
Ulrich Krupp ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Retained Austenite ◽  
Elevated Temperatures ◽  
Mechanical Performance ◽  
Mechanical Stability ◽  
Electron Backscatter Diffraction ◽  
Cost Effective ◽  
Tensile Tests ◽  
Thermal Stability Of

AbstractAdvanced medium-Mn sheet steels show an opportunity for the development of cost-effective and light-weight automotive parts with improved safety and optimized environmental performance. These steels utilize the strain-induced martensitic transformation of metastable retained austenite to improve the strength–ductility balance. The improvement of mechanical performance is related to the tailored thermal and mechanical stabilities of retained austenite. The mechanical stability of retained austenite was estimated in static tensile tests over a wide temperature range from 20 °C to 200 °C. The thermal stability of retained austenite during heating at elevated temperatures was assessed by means of dilatometry. The phase composition and microstructure evolution were investigated by means of scanning electron microscopy, electron backscatter diffraction, X-ray diffraction and transmission electron microscopy techniques. It was shown that the retained austenite stability shows a pronounced temperature dependence and is also stimulated by the manganese addition in a 3–5% range.

Sign in / Sign up

Export Citation Format

Share Document