Quasi-static tensile test - introduction

2014 ◽  
pp. 83-87
Author(s):  
C. Bierögel ◽  
W. Grellmann
Keyword(s):  
Tensile Test ◽  
Static Tensile Test ◽  
Static Tensile

Static Tensile Test of rGO-PDMS Composite

2018 ◽  
pp. 46-51
Author(s):  
Barbara NASIŁOWSKA ◽  
Piotr WAWRZYNIAK ◽  
Zdzisław BOGDANOWICZ ◽  
Paweł BOGUSZ ◽  
Aneta BOMBALSKA ◽  
...  
Keyword(s):  
Tensile Test ◽  
Static Tensile Test ◽  
Static Tensile

Influence of Technological Options on the Material Reliability of AlSi17Cu5 Cast Alloy

2015 ◽  
Vol 229 ◽  
pp. 17-24
Author(s):  
Jaroslaw Piątkowski
Keyword(s):  
Tensile Strength ◽  
Yield Strength ◽  
Tensile Test ◽  
Material Property ◽  
Cast Alloy ◽  
Static Tensile Test ◽  
Static Tensile ◽  
Technological Options

In the dissertation the influence of overheating of around 250oC above Tliq on the material reliability of AlSi17Cu5 cast alloy has been shown. On the basis of static tensile test, the following had been determined: HB hardness, tensile strength and yield strength for four, chosen technological variants. The results were the base to verify the thesis of compliance between tested feature arrangement and normal arrangement, and on this ground also material reliability determined with Weibull’s statistic arrangement had been defined. This parameter grasp the interdependence between lasting probability and chosen material property of the alloy.

High-speed imaging on static tensile test for unidirectional CFRP

2008 ◽  
Author(s):  
Hideaki Kusano ◽  
Yuichiro Aoki ◽  
Yoshiyasu Hirano ◽  
Yasushi Kondo ◽  
Yosuke Nagao
Keyword(s):  
Tensile Test ◽  
High Speed ◽  
High Speed Imaging ◽  
Static Tensile Test ◽  
Static Tensile

Simulation of Metal Material Quasi-Static Tensile Test Based on ABAQUS

2013 ◽  
Vol 328 ◽  
pp. 985-989 ◽  
Author(s):  
Duo Nian Yu ◽  
Yuan Wang ◽  
Jun Wei She
Keyword(s):  
Tensile Test ◽  
Rapid Development ◽  
Simulation Data ◽  
Metal Material ◽  
Static Tensile Test ◽  
Fitting Method ◽  
Numerical Fitting ◽  
Static Tensile ◽  
Metal Materials ◽  
Tensile Test Data

As the rapid development of metal material science, various kinds of metal materials have emerged. The strain and stress characteristics of materials are prerequisites of its application in the actual production. So it has to take many experiments which will cost a lot of manpower, materials, time and equipments to get the characteristics. In this paper, we simulate the process of a metal material quasi-static tensile test based on ABAQUS to discuss the accuracy of simulation data with experimental data. The simulation data is compared with the quasi-static tensile test data of a new kind of aluminum and the verification of accuracy is based on numerical fitting method.

Influence of Forming on the Properties of Alloy Based on the Matrix of FeAl Intermetallic Phase

2013 ◽  
Vol 212 ◽  
pp. 49-52 ◽  
Author(s):  
Janusz Cebulski ◽  
Katarzyna Basa ◽  
Dorota Pasek
Keyword(s):  
Tensile Test ◽  
Crack Surface ◽  
Intermetallic Phase ◽  
Optical Microscope ◽  
Forming Process ◽  
Process Measures ◽  
Matrix Microstructure ◽  
Static Tensile Test ◽  
The Matrix ◽  
Static Tensile

Presented article describes results of studies concerning on influence of forming processes on alloy characteristics based on the FeAl intermetallic phase matrix. Microstructure of the alloy was evaluated with optical microscope after crystallization and forming process. Measures of hardness were taken using Vickers method. Static tensile test was used to set limitation of malleability and ultimate tensile strength. Crack surface after static tensile test was observed using scanning electron microscope.

scholarly journals Advanced Configuration Parameters of Post Processor Influencing Tensile Testing PLA and Add-Mixtures in Polymer Matrix in the Process of FDM Technology

2021 ◽  
Vol 11 (13) ◽  
pp. 6212
Author(s):  
Jozef Török ◽  
Monika Törökova ◽  
Darina Duplakova ◽  
Zuzana Murcinkova ◽  
Jan Duplak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Reference Sample ◽  
Test Sample ◽  
Original Material ◽  
Surface Layers ◽  
Standard Type ◽  
Static Tensile Test ◽  
Static Tensile ◽  
The Individual

The present paper focuses on the configuration possibilities of post -processor influencing mechanical properties of a given test sample produced by the FDM printer from different materials. The research consists of assessing the composite material configurations through a static tensile test conducted on 80 samples produced. The samples were produced based on ISO 527-2 standard, type 1A, with a horizontal position and a layer height of 0.2 mm. The individual samples consisted of four basic groups of materials—the pure Polylactic acid (PLA) plastic (reference sample), and three composite samples with admixtures—PLA matrix with a copper admixture, PLA matrix with an iron admixture, and PLA matrix with a steel admixture. The static tensile test was conducted at a test speed of 5 mm/min. During the research, reference samples (pure PLA) were assessed in five orientations. Samples made of the PLA composite materials with admixtures were manufactured, tested, and evaluated only in the 0° orientation. The paper concludes by comparing the results of measurement with the original material, free from additives, and with the researched influence of the orientation of the prints on the resulting mechanical properties of shear samples and their surface structure. In the conducted experiments, the lowest tensile strength has been demonstrated in test samples the orbital transitions and the upper surface layers of which were parallel to the infill.

scholarly journals Numerical Analysis of Static Tensile Test of the Sample Made of Polyethylene Reinforced by Halloysite Nanoparticles

2019 ◽  
Vol 136 (6) ◽  
pp. 996-1000
Author(s):  
A. Śliwa ◽  
W. Kwaśny ◽  
M. Nabia k ◽  
R. Dziwis
Keyword(s):  
Numerical Analysis ◽  
Tensile Test ◽  
Static Tensile Test ◽  
Static Tensile
Sign in / Sign up

Export Citation Format

Share Document