Investigation of Fused Deposition Modeling (FDM) Process Parameters Influencing the Additively Manufactured Part Characteristics: A Review Paper

Author(s):  
Mohit Bhayana ◽  
Jaswinder Singh ◽  
Bineetpal Singh ◽  
Jaspreet Singh
2021 ◽  
pp. 251659842110311
Author(s):  
Shrikrishna Pawar ◽  
Dhananjay Dolas1

Fused deposition modeling (FDM) is one of the most commonly used additive manufacturing (AM) technologies, which has found application in industries to meet the challenges of design modifications without significant cost increase and time delays. Process parameters largely affect the quality characteristics of AM parts, such as mechanical strength and surface finish. This article aims to optimize the parameters for enhancing flexural strength and surface finish of FDM parts. A total of 18 test specimens of polycarbonate (PC)-ABS (acrylonitrile–butadiene–styrene) material are printed to analyze the effect of process parameters, viz. layer thickness, build orientation, and infill density on flexural strength and surface finish. Empirical models relating process parameters with responses have been developed by using response surface regression and further analyzed by analysis of variance. Main effect plots and interaction plots are drawn to study the individual and combined effect of process parameters on output variables. Response surface methodology was employed to predict the results of flexural strength 48.2910 MPa and surface roughness 3.5826 µm with an optimal setting of parameters of 0.14-mm layer thickness and 100% infill density along with horizontal build orientation. Experimental results confirm infill density and build orientation as highly significant parameters for impacting flexural strength and surface roughness, respectively.


2021 ◽  
pp. 026248932110409
Author(s):  
G Radhakrishna ◽  
Rupesh Dugad ◽  
Abhishek Gandhi

In this article, the development of microcellular structure foams has developed by integrating the two successful and existing technologies, namely CO2 gas batch foaming and Fused Deposition Modeling (FDM) 3D printing technique. It is a novel approach to manufacture complex design porous products for customized applications. The eventual cell morphologies of the extruded 3D printing filament depends on the process parameters pertaining to both microcellular foaming and 3D printing processes. Further, morphological study has been conducted to evaluate the cell morphologies of the 3D printing filament developed through customized FDM setup. During this process, the significance of various process parameters including saturation pressure, saturation time, desorption time, feed rate and extrusion temperature were thoroughly studied. To pursue this study base material used was acrylonitrile butadiene styrene (ABS). The 3D printed filaments consisted of cells with an average cell size in the range of 2.3–276 µm and the average cell density in the range of 4.7 × 104 to 4.3 × 109 cells/cm3. Finally, it has found that by controlling the process parameters different cell morphologies can be developed as per the end application.


Author(s):  
Jagadish ◽  
Sumit Bhowmik

Fused deposition modeling (FDM) is one of the emerging rapid prototyping (RP) processes in additive manufacturing. FDM fabricates the quality prototype directly from the CAD data and is dependent on the various process parameters, hence optimization is essential. In the present chapter, process parameters of FDM process are analyzed using an integrated MCDM approach. The integrated MCDM approach consists of modified fuzzy with ANP methods. Experimentation is performed considering three process parameters, namely layer height, shell thickness, and fill density, and corresponding response parameters, namely ultimate tensile strength, dimensional accuracy, and manufacturing time are determined. Thereafter, optimization of FDM process parameters is done using proposed method. The result shows that exp.no-4 yields the optimal process parameters for FDM and provides optimal parameters as layer height of 0.08 mm, shell thickness of 2.0 mm and fill density of 100%. Also, optimal setting provides higher ultimate TS, good DA, and lesser MT as well as improving the performance and efficiency of FDM.


Sign in / Sign up

Export Citation Format

Share Document