An improved machine tool volumetric error compensation method based on linear and squareness error correction method

2020 ◽  
Vol 106 (11-12) ◽  
pp. 4731-4744 ◽  
Author(s):  
Weiguo Gao ◽  
Lingtao Weng ◽  
Jinyi Zhang ◽  
Wenjie Tian ◽  
Guanwei Zhang ◽  
...  
Keyword(s):  
Machine Tool ◽  
Error Correction ◽  
Error Compensation ◽  
Correction Method ◽  
Compensation Method ◽  
Volumetric Error ◽  
Error Correction Method ◽  
Squareness Error

Design of a temperature error correction method used for meteorology and climate research

2021 ◽  
Vol 263 ◽  
pp. 105817
Author(s):  
Jie Yang ◽  
Qingquan Liu ◽  
Gaoying Chen ◽  
Xuan Deng ◽  
Li Zhang
Keyword(s):  
Error Correction ◽  
Correction Method ◽  
Temperature Error ◽  
Climate Research ◽  
Error Correction Method

scholarly journals A Non-Delay Error Compensation Method for Dual-Driving Gantry-Type Machine Tool

Processes ◽  
2020 ◽  
Vol 8 (7) ◽  
pp. 748
Author(s):  
Qi Liu ◽  
Hong Lu ◽  
Xinbao Zhang ◽  
Yu Qiao ◽  
Qian Cheng ◽  
...  
Keyword(s):  
Machine Tool ◽  
Error Compensation ◽  
Prediction Method ◽  
Compensation Method ◽  
Industrial Robots ◽  
Numerical Control ◽  
Heavy Duty ◽  
Positioning Errors ◽  
Compensation Methods ◽  
Type Machine

The drive at the center of gravity (DCG) principle has been adopted in computer numerical control (CNC) machines and industrial robots that require heavy-duty and quick feeds. Using this principle requires accurate corrections of positioning errors. Conventional error compensation methods may cause vibrations and unstable control performances due to the delay between compensation and motor motion. This paper proposes a new method to reduce the positioning errors of the dual-driving gantry-type machine tool (DDGTMT), namely, a typical DCG-principle-based machine tool. An error prediction method is proposed to characterize errors online. An algorithm is proposed to quickly and accurately compensate the errors of the DDGTMT. Experiment results verify that the non-delay error compensation method proposed in this paper can effectively improve the accuracy of the DDGTMT.

scholarly journals Performance of the FMI cosine error correction method for the Brewer spectral UV measurements

2018 ◽  
Vol 11 (9) ◽  
pp. 5167-5180 ◽  
Author(s):  
Kaisa Lakkala ◽  
Antti Arola ◽  
Julian Gröbner ◽  
Sergio Fabian León-Luis ◽  
Alberto Redondas ◽  
...  
Keyword(s):  
Error Correction ◽  
Correction Method ◽  
Uv Spectra ◽  
Correction Coefficient ◽  
Finnish Meteorological Institute ◽  
Angular Response ◽  
Error Correction Method ◽  
Radiation Distribution ◽  
Rapid Changes ◽  
Relative Differences

Abstract. Non-ideal angular response of a spectroradiometer is a well-known error source of spectral UV measurements and for that reason instrument specific cosine error correction is applied. In this paper, the performance of the cosine error correction method of Brewer spectral UV measurements in use at the Finnish Meteorological Institute (FMI) is studied. Ideally, the correction depends on the actual sky radiation distribution, which can change even during one spectral scan due to rapid changes in cloudiness. The FMI method has been developed to take into account the changes in the ratio of direct to diffuse sky radiation and it derives a correction coefficient for each measured wavelength. Measurements of five Brewers were corrected for the cosine error and the results were compared to the reference travelling spectroradiometer (QASUME). Measurements were performed during the RBCC-E (Regional Brewer Calibration Center – Europe) X Campaign held at El Arenosillo, Huelva (37∘ N, 7∘ W), Spain, in 2015. In addition, results of site audits of FMI's Brewers in Sodankylä (67∘ N, 27∘ E) and Jokioinen (61∘ N, 24∘ E) during 2002–2014 were studied. The results show that the spectral cosine error correction varied between 4 and 14 %. After that the correction was applied to Brewer UV spectra the relative differences between the QASUME and the Brewer diminished even by 10 %. The study confirms that the method, originally developed for measurements at high latitudes, can be used at mid-latitudes as well. The method is applicable to other Brewers as far as the required input parameters, i.e. total ozone, aerosol information, albedo, instrument specific angular response and slit function are available.

scholarly journals Burst Error Correction Method Based on Arithmetic Weighted Checksums

Engineering ◽  
2012 ◽  
Vol 04 (11) ◽  
pp. 768-773 ◽  
Author(s):  
Saleh Al-Omar ◽  
Atef Obeidat
Keyword(s):  
Error Correction ◽  
Correction Method ◽  
Burst Error ◽  
Error Correction Method
Sign in / Sign up

Export Citation Format

Share Document